517417
6
Zoom out
Zoom in
Previous page
1/26
Next page
GBGB
TROUBLESHOOTING
If the following problems occur …then…
A wrong weight format appears followed by kg, lb, or st-lb
Refer to “Switching the Weight Mode” on p.5.
”Lo” appears on the display, or all the data appears and immediately
disappears.
Batteries are low. When this message appears, be sure to replace the batteries immediately, since weak batteries will
affect the accuracy of your measurements. Change all the batteries at the same time with new AA-size batteries.
Note: Your settings will not be erased from the memory when you remove the batteries.
”Error” appears while measuring.
Please stand on the platform keeping movement to a minimum.
The unit cannot accurately measure your weight if it detects movement.
The Body Fat Percentage measurement does not appear or ”-----” appears
after the weight is measured.
Your personal data has not been programmed. Follow the steps on p.6.
Make sure socks or stockings are removed, and the soles of your feet are clean and properly aligned with the guides
on the measuring platform.
”OL” appears while measuring.
Reading cannot be obtained if the weight capacity is exceeded.
”Error %” appears while measuring.
The Body Fat Percentage is more than 75%, readings cannot be obtained from the unit.
87
TAKING WEIGHT AND BODY FAT READINGS
PROGRAMMING THE GUEST MODE
After programming your personal data you are ready to take a reading.
1. Select Personal Data Number
Press the Up button turn on. Use the Up/Down buttons to select your
Personal data number. Press the Set button to confirm.
(Release the key within 3 seconds or the display will show “Error”.)
The unit will beep and the display will show the programmed data.
The unit will beep again and the display will show “0.0”.
Now step onto the platform.
Note:
•If you step onto the platform before “0.0” appears the display will show “Error” and you will
not obtain a reading. Furthermore, if you do not step onto the measuring platform within
about 30 seconds after “0.0” appears, the power is shut-off automatically.
•When using the “Up” button to turn the unit on, the personal data number last used will
appear first.
•Numbers that are not pre-programmed are automatically skipped.
2. Get Your Readings
Your weight will be shown first.
Continue to stand on the platform.
“00000” will appear on the display and disappear one by one from left to
right.
The display will then flash your %TBW, weight and %FAT alternately 3 times.
Note: Do not step off until Body Fat % is shown.
To obtain previous readings, press the SET button while the current readings are being
displayed.
Press the SET button again to go back to the current Weight and Body Fat % result display.
The Guest mode allows you to use the monitor without losing the
information already assigned to a Personal Data Number.
To program the Guest mode, use the Down button marked with a “G” to turn
on the power. Then follow steps 3 through 5 in “
Setting and Storing Data in
Memory
” (p.6.) The unit will beep twice and the display will show “0.0”.
Step onto the platform. Next follow the directions for “Get Your Reading”
(p.7).
Note: If you step onto the platform before “0.0” appears the display will show “Error” and
you will not obtain a reading.
TAKING WEIGHT MEASUREMENT ONLY
Select Weight-Only Mode
Using your toe, tap the Weight-only key. After 2 or 3 seconds, “0.0” will
appear in the display and the unit will beep. When “0.0” appears in the
display, step onto the platform. The body weight value will appear.
If you
remain on the platform, the display will flash for about 30 seconds, and then the power
will automatically turn off. If you step off the platform, the weight will continue to show for
about 5 seconds, then “0.0” will appear and the unit will shut off automatically.
UNDERSTANDING YOUR READING
Healthy Range Indicator
Your body fat monitor/scale automatically compares your body fat reading to the
Healthy Body Fat Range chart.
Following your body fat percentage reading, a black bar will flash along the bottom
of the display, identifying where you fall within the Body Fat Ranges for your age
and gender. For example, if the squares appear above (0) area your range is within
the Healthy Range – if they appear over (-) area, your reading is below the Healthy
Range. For more about the Healthy Range, see page 2.
Under Healthy Over Obese
(-) : Underfat; below the healthy body fat range. Increased risk for health problems.
(0) : Healthy; within the healthy body fat percentage range for your age/gender.
(+) : Overfat; above the healthy range. Increased risk for health problems.
(++) : Obese; high above the healthy body fat range. Greatly increased risk of obesity-related health problems.
Note:Range of user age is between 18-99
UM050/取説 06.2.22 6:09 PM ページ11
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tanita UM-050 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tanita UM-050 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info