540608
4
Zoom out
Zoom in
Previous page
1/27
Next page
6 7
1
2
3
1
2
3
EN
NL
DE
JP
IT
ES
FR
CH
The accuracy of the Flow's power display depends on factors such as the pressure of the cylinder
against the tyre, the tyre pressure, fluctuating magnetic forces and the difference in mains voltage.
To guarantee a good power measurement, the brake must be calibrated. For optimal calibration
we recommend cycling at least 3 minutes beforehand to warm-up the brake. Make sure the tyre
pressureisbetween7and8bar.
Brake calibration
The calibration value 0 appears at the bottom. You start the brake calibration with the Up arrow,
whichcausesthreedashestoappearatthebottomofthedisplay.Cycleataspeedabove30km/h
(or19mi/h)untilthewordSTOPappears.Themomentyoustop,theFlowcomputermeasuresthe
deceleration of the rear wheel and the new calibration value appears on the display.
If the calibration fails (e.g. because you began pedalling during the measurement), ERROR appears on the display.
You can start the calibration again with the Up arrow. You can set the calibration value to 0 with the Down arrow.
Use MODE to confirm the settings and switch to the training display.
Settings before you begin
The Flow registers four training parameters: speed, power, cadence and heart rate.
Two training parameters are shown at any time, on the 2nd and 3rd lines of the display. With the
Up arrow you can switch the 2nd line from speed to cadence, power and heart rate. With the
Down arrow you can switch the training parameters on the 3rd line.
MODE functions for SPEED (km/h or mi/h)
The MODE functions on the 1st line of the display correspond to the training parameter on the 2nd
line. When the 2nd line is set to speed, the MODE key switches between ETM (elapsed time), TRP
(trip time), ODO (odometer), MAX (maximum speed) and AVS (average speed).
The values only reflect the actual time spend cycling since the computer was reset or switched on. If you take a
break, the data will be retained. Once you resume cycling, the computer begins calculating again, using all the data.
MODE functions for CADENCE (Cad)
When the 2nd line is set to cadence (Cad), TRP means the total number of pedal revolutions during
thetrip,MAXmeansthemaximumpedallingfrequencyandAVStheaveragepedallingfrequency.
Training with the Flow
ETM TRP ODO MAX AVS
MODE
ETM TRP MAX AVS
MODE
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tacx Flow computer at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tacx Flow computer in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 5,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info