468139

Synq SMX-1 Manual

8
Zoom out
Zoom in
Previous page
1/43
Next page
ENGLISH USER MANUAL
SYNQ 11/82 SMX-1 DJ-MIxer
41.INPUT SOURCE SELECTOR: Used to select the correct input on each channel:
Phono, line, aux or mic. On some channels there are additional input selectors on
the back, near the input connectors!
Hint: Line, Aux, CD, Tuner, etc…are differentnames for inputs with almost the same signallevels.
42.GAIN LEVEL: Adjusts the input level on each channel, range goes from zero to
maximum. Use this control to adjust the level on the VU-meter at about 0dB.
CONNECTIONS
When connecting or changing connections, always turn off the units before.
This connection diagram is just an example of what is possible. Many other connections
are possible. Just keep the following remarks in mind:
Always connect cinch cables in the same way:
o white or black cinch connector left channel
o red cinch connector right channel
ENGLISH USER MANUAL
SYNQ 12/82 SMX-1 DJ-MIxer
When you connect a CD-player, Cassette deck, MD-player, tuner, video recorder etc. to
one of the inputs, don’t forget to put the source selector of that channel to “LINE” or
“AUX”.
When connecting a microphone to channel 4, switch the source selector to “MIC”.
When you connect a turntable to one of the inputs, don’t forget to put the source
selector of that channel to “PHONO”. (attention: newer turntables may have a line
output, read the user manual of your turntable to be sure)
Many Turntables have a GND-connection. It is preferable to connect this signal ground
to the SMX-1. Use the GND-connections, close to the signal input connectors.
The Record input of an analog recording device can be connected to the record output
of the SMX-1 to make analog recordings.
If you have a digital recorder, connect it to the coaxial digital output of the mixer. You
can obtain outstanding digital recordings.
To ensure the best possible sound quality, short-circuit pins are installed on all unused
phono inputs. When connecting a turntable to the SMX-1, first remove the short-circuit
pins of the input you want to use. Keep these short-circuit pins in a safe place for
eventual later use.
CHANGING THE FADERS
One of the big advantages of this mixer is the possibility to change the channel faders,
even while the mixer is in use.
This is what you must do to change a channel fader:
Remove the fader knobs from the faders.
Remove the 4 screws that hold the small
front panel around the faders.
Remove the 3 screws of the fader you want
to change.
Gently remove the fader from its position.
Put the new fader gently in place. Be sure
to fit the contacts into the connector on the
mixer PCB-board.
Put the 3 screws from the fader back in
place
Put the small front plate back in place with
the 4 screws.
Done!
This is what you must do to change the cross fader:
Remove the fader knob from the cross fader.
Remove the 2 screws that keep the cross fader in place.
Gently remove the fader and the cover plate from their position.
Unplug the cross fader from the cable (unplug the cable by pulling the connector, NOT
the cable!)
Press the new cross fader on the cable.
Put the cross fader back in place with the small cover plate and the 2 screws.
Done!
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Synq SMX-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Synq SMX-1 in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 1,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info