517153
17
Zoom out
Zoom in
Previous page
1/24
Next page
17
10. INSPECTION AND MAINTENANCE BEFORE RIDING
§THROTTLE VALVE HANDLE CLEARANCE ADJUSTMENT §
y Correct clearance allows throttle vale handle to rotate
2~6mm.
y Loosen the lock nut first, then turn the adjust nut to adjust.
Tighten the lock nut securely when finished.
§INSPECTION AND MAINTENANCE OF BATTERY §
y The motorcycle is equipped with a maintenance-free type battery, so it is unnecessary to check and
add electrolyte. Have your motorcycle checked by SYM Authorized Dealer or Franchised Dealer should
any abnormality is found.
Cleaning of battery terminals
y Remove the battery terminals and clean if there are
dirt and corrosion on them.
y Battery removal procedures are as follows:
Turn ignition switch to the “OFF” position, then
remove negative cable screw firstly and disconnect
the negative cable. Then, remove positive cable
screw and positive cable.
CAUTION:
y Clean the battery posts with warm water if the posts are eroded and have some white powders
on them.
y If there is an obvious erosion on the terminals, disconnect the cables, and then clean the erosion
off with a steel brush or a piece of sandpaper.
y Install battery cable after cleaning and apply a thin coat of grease on the terminals.
y Install battery in reverse order of removal.
y The motorcycle is equipped with a maintenance-free type battery, so it is unnecessary to check and
add electrolyte. Have your motorcycle checked by SYM Authorized Dealer or Franchised Dealer should
any abnormality is found.
CAUTION:
y This is a closed type battery. Never remove the caps.
y In order to prevent electric leakage and self-discharge when the battery sits idle for long periods.
Remove battery from motorcycle, store it in well-ventilated and dimly lighted place after the battery
has been fully charged. Disconnect battery’s negative cable if the battery is still kept on the
motorcycle.
y If the battery needs to be replaced, replace with a same closed-type battery (Maintenance-Free).
Check Items:
1. Check throttle valve cable to see if it can be moved
smoothly from a closed position to a wide open position.
2. Rotate steering handle from side to side to check if the
throttle valve cable is interfered.
3. Check to see if the throttle valve cable is obstructed by
other cables preventing it from being operated
2~6 mm
Lock nut
Adjust nut
Negative
Positive
17


Need help? Post your question in this forum.

Forumrules
1

Forum

sym-symply-50

Reset search

  • can anyone show me how to put together the side stand? I bought one from a breaker Submitted on 21-5-2020 at 13:08

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sym SYMPLY 50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sym SYMPLY 50 in the language / languages: English as an attachment in your email.

The manual is 0,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info