660406
19
Zoom out
Zoom in
Previous page
1/24
Next page
19
§CHECKING AND CHANGING FUSES §
Turn off ignition switch, and check fuses if they are intact. Replace the blown fuse with a new one having the
same specified amperage rating (10A&15A). Using a fuse of more than (10A or 15A) amperes, a brass or iron
wire to replace a blown fuse is strictly prohibited to avoid damaging the electrical system and the circuit.
Remove the storage box, and you’ll find the fuse holder near battery.
Open the fuse box cover, and pull out the fuse. Check it for damage or broken.
Fuses must be firmly secured with wire connectors when replacing. Loose connections will result in
overhead and damage.
Use only parts having the specified specification to replace electrical components such as light bulbs.
Using parts not having the specified specifications for replacement may cause the fuse to blow and
over-discharge the battery.
Avoid spraying water directly on or around fuse box when washing the scooter.
If the new fuse burn out quickly again, please check the faulty reason before replace it again. Take your
scooter to your dealer for an inspection if a fuse is blown by unknown causes.
§CHECKING THE TURN SIGNAL LIGHTS AND HORN §
Turn the ignition switch key to the “ON” position.
Turn on the turn signal light switch, and make sure that the front & rear and left & right signal lights flashes
and also check if the warning buzzer sounds.
Check turn signal light covers if they are dirty, crack, or loosen.
Press horn button to check if it works.
§CHECKING THE FRONT AND REAR LIGHTS §
Start engine and turn on the head lamp switch. Check if head lamp and rear lamp come on.
Check the brightness and direction of front light by wall to see if it is correct.
Check the head lamp cover if it is dirty, crack, or loosen.
§CHECKING THE BRAKE LIGHT §
Turn the ignition switch key to the “ON” position, hold the hand-braking levers for front and rear wheels.
Check if the brake lights come on.
Check the brake light cover if it is dirty, crack, or loosen.
CAUTION:
Specified specification bulbs should be used for turn signal lights. Otherwise, the normal operation of
turn signal lights will be affected.
Turn on the turn signal light before turning or switching lane to warn driver of vehicles behind.
Turn off the turn signal light immediately by pressing its button down after using. Otherwise, the
flashing of twin signal lights may confuse the drivers of vehicles behind.
CAUTION:
Use only specified specification bulbs, do not use bulbs with different specifications to avoid damaging
electrical system, burning out bulbs, and discharging the battery.
Do not modify or add other electrical components to prevent over load or short circuit which may result
in a fire and burn down the motorcycle in serious cases.
INSTALLATION
Press in from above
REMOVE
Wire
Fuse connectors
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sym SYMPHONY SR 50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sym SYMPHONY SR 50 in the language / languages: English as an attachment in your email.

The manual is 1,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info