673291
8
Zoom out
Zoom in
Previous page
1/28
Next page
7
7. Use of Each Component
Speedometer
Indicates riding speed there are two type of unit (Km/h) or (mph).
LCD monitor (Including Odometer)
Press “MODE” to switch showing the total mileage/ short mileage/ oil use.
Press “SET” to switch showing the battery voltage/ time.
High Beam Indicator
This indicator comes on with high beam headlight is turned on.
Turn Signal Indicator
The left or right Indicator will be flashing according to the operated directions of turn signal light switch
when it is turned on.
Fuel Gauge
The pointer in this gauge shows how much fuel remains in the tank.
If the pointer stays in “E” position when key switch is turned to “ON”, please fill up with gasoline (over 92
Unleaded gasoline)
EFi trouble warning indicator
When turn the main switch to “ON”, this warning indicator will come on and then go off after the
engine is running. It displays the condition of the EFi system is working correctly. If there is any
problem on the EFi system, the warning indicator will remain on all the time or does not come on.
Please contact with a SYM dealer to check the self-diagnosis system or electrical connections.
Engine Oil Change Indicator
This indicator shows when to change engine oil by light. Usually, the scooter has been ride
approximately 1,000 km, the indicator will show its light. Then, it means you should change or add the
engine oil, and turn the mileage to “0” in the OIL mode. After replacing it, please turn to KEY ON. Press
the “SET” 2 times in the “OIL” mode, let the indicator’s light be off, and turn the mileage to “0” in the OIL
mode.
Notice: 1. Please change oil when the initial 300 km, then change every 1,000 km.
2. If your motor’s mileage has already been exceeded the kilometers, but the light does not show,
please go to the SBC/ dealer store for check.
Display mode switch:
1. When the key switch is turned to “ON” in “TOTAL” mode, Press “MODE” button within 1 second to
change between “TOTAL” , “OIL” and ”TRIP” modes.
2. The “TOTAL” means the total mileage of the motor, cannot be reset. But in “TRIP” mode, and press the
SET“ over 2 seconds, then the mileage can be erased and newly calculated.
3. Under “CLOCK” mode, press “SET” 1 second, will switch to “VOLTAGE” showing.
Time setting
1. Showing the 24 hour mode time (
0:00~23:59). Time allows ±2 seconds tolerance.
2. When the key switch is turned to “ON,” the clock will show the 24 hour mode hour/ minute .
3. Under the “CLOCK” mode, press “ MODE” button (over 2 seconds) to enter “TIME” setup mode,
Then press MODE” 1 second, then you could switch setup mode (as below):
HOUR MIN(10min) MIN(1min)
2. Under time setting mode, press “SET” button shortly to increase the readings. The number will
increase 1 at one time, it will automatically leave the setup mode if you do not take action within
30 seconds.
TOTAL
CLOCK
TRIP
CLOCK
OIL
CLOCK
OIL
VOLTAGE
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sym Mio 115 - FS11W1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sym Mio 115 - FS11W1 in the language / languages: English as an attachment in your email.

The manual is 9,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info