577252
5
Zoom out
Zoom in
Previous page
1/32
Next page
1
1. Contents
Content/ Sub
j
ect
1. Contents ........................................................................................................................ 1
2. Control location ............................................................................................................. 3
3. Before riding .................................................................................................................. 8
4. Safety riding .................................................................................................................. 8
5. Driving............................................................................................................................. 9
6. Use genuine spare parts ............................................................................................... 9
7. Use of each component .............................................................................................. 10
Gauges ....................................................................................................................... 10
Operation of ignition switch ......................................................................................... 13
Use of buttons ............................................................................................................. 14
Saddle lock .................................................................................................................. 15
Safety helmet hook .......................................................................................................15
Storage box.....................................................................................................................16
Fuel tank cap ............................................................................................................... 16
Brake ........................................................................................................................... 16
Parking method ........................................................................................................... 17
8. Important points and cautions for starting engine ........................................................ 18
9. The best way to drive off ............................................................................................. 19
The control of throttle valve handle ............................................................................. 19
10. Inspection and maintenance before riding .................................................................. 19
Routine inspection ....................................................................................................... 19
Inspection and replenishment of engine oil ................................................................. 20
Inspection of fuel level ................................................................................................. 20
Transmission oil inspection and change ..................................................................... 21
Inspection and adjustment of brake free play .............................................................. 21
Disc brake inspection [Depending on models] ............................................................ 22
Throttle valve handle clearance adjustment.................................................................. 23
Inspection and maintenance of battery ....................................................................... 23
Tire inspection ............................................................................................................. 24
Steering handle front shock absorbers inspection ....................................................... 25
Checking and changing fuses ..................................................................................... 25
Checking the turn signal lights and horn ..................................................................... 26
Checking the front and rear lights ............................................................................... 26
1. Contents
2
Checking the brake light .............................................................................................. 26
Checking for fuel leakage ............................................................................................ 26
Checking the lubrication of body’s various mechanisms ............................................. 26
Checking the spark plug .............................................................................................. 27
Checking the air cleaner ............................................................................................. 27
11. When there is an abnormal condition or a trouble ....................................................... 28
Diagnosis when engine does not start ........................................................................ 28
12. Periodical Maintenance Schedule ............................................................................... 29
13. Specification ................................................................................................................ 30
14. Postscript .................................................................................................................... 32
3
2. Control location
MODEJET 50/100 SERIES (BL05WA-6)
Head light
Front brake lever Rear brake lever
Tail light
Helmet hook
Fuel tank cap
Engine number
Storage box
Muffler
Fuses / C.D.I. /
Eng. Oil tank cap
Light / Starter switch
High & Low beam /
Turn signal / Horn switch
Air cleaner
Frame number
Front turn signal
Ignition switch
Rear turn signal
Seat lock
Rear turn signal
4
2. Control location
MODE BL05W6-A SERIES
Fuel tank cap
Light / Starter switch
Rear turn signal
Head light
Tail light
Engine number
Storage box
Fuses / C.D.I. /
Eng. Oil tank cap
High & Low beam /
Turn signal / Horn switch
Helmet hook
Air cleaner
Front turn signal
Ignition switch
Muffler
Rear brake lever
Front brake lever
Seat lock
Frame number
5
2. Control location
MODEMASK SERIES (BF05W)
Head light
Front brake lever Rear brake lever
Tail light
Rear turn signal
Helmet hook
Fuel tank cap
Engine number
Storage box
Muffler
Fuses / C.D.I. /
Eng. Oil tank cap
Light / Starter switch
High & Low beam /
Turn signal / Horn switch
Air cleaner
Front turn signal
Ignition switch
Rear turn signal
Seat lock
Frame number
6
2. Control location
MODEBS05W SERIES
Head light
Front brake lever
Rear brake lever
Tail light
Helmet hook
Fuel tank cap
Engine number
Storage box
Muffler
Fuses / C.D.I. /
Eng. Oil tank cap
Light / Starter switch
High & Low beam /
Turn signal / Horn switch
Air cleaner
Front turn signal
Ignition switch
Rear turn signal
Seat lock
Frame number
7
2. Control location
MODEJet SportX 50 SERIES (BK05W)
Head light
Front brake lever
Rear brake lever
Tail light
Fuel tank cap
Engine number
Storage box
Muffler
Fuses / C.D.I. /
Eng. Oil tank cap
High & Low beam /
Turn signal / Horn switch
Air cleaner
Ignition switch
Rear turn signal
Seat lock
Frame number
ENG. Stop / Starter switch
8
3. Before riding 4. Safe riding
This manual describes the correct usage of this scooter including safety riding, simple inspection methods
and so on.
For a more comfortable and safety riding, please read this manual carefully.
Thank you very much for your patronage
In order to maximize your scooter’s performance, a periodical inspection and maintenance should be
completely carried out. We recommend that after riding your new scooter for the first 300 kilometers,
you should take your scooter to the original dealer for an initial inspection, and to have your scooter
inspected periodically every 1,000 kilometers thereafter.
In case the scooter’s specifications and construction are modified and different from the photos and
diagrams on the owner’s manual/catalogues, the specifications and construction of the actual scooter
shall prevail.
4. SAFE RIDING
It is very important to be relax and clothe properly when driving, observe traffic regulations, do not rush,
always drive carefully and relaxed.
Usually, most people would ride their newly bought scooter very carefully, but after they became familiar
with their scooters, they tended to become reckless which may result in an accident.
To remind you:
Please wear a safety helmet, and properly tighten the chin belt when riding a scooter.
Clothes with open or loose cuffs may be blown by wind and cause the cuffs to get caught on the
steering handle and thus affects riding safety. So, put on clothes with tight sleeves.
Hold the steering handle by both hands when riding. Never ride with only one hand.
Observe the speed limit.
Perform periodical maintenance and inspection in accordance with the schedule.
WARNING!!
To avoid getting burned by exhaust pipe when taking a passenger. Make sure your passenger has
put his/her feet on the pedals.
After running, the exhaust pipe is very hot, be careful not to get burned when conducting an
inspection or maintenance.
After running, the exhaust pipe is very hot, select a suitable location to park your scooter to avoid
others getting burned by the exhaust pipe.
CAUTION:
Modified scooter will affect its structure or performance, and cause poor engine operation or exhaust
noise, which will result in shortening the scooter’s service life. Besides, modification is illegal and
does not conform to the original design and specifications. A modified scooter will not be covered
by warranty, therefore, do not modify your scooter at will.
9
5. Driving 6. Use genuine spare parts
Keep the related parts of your body such as arms, palms, lumbar, and toes relax and ride with the
most comfortable posture in order to be able to react quickly whenever it is necessary.
Rider’s posture will great influent riding safety. As for the riding position, please always keep your
body’s gravity on the center of seat. If your body’s gravity is placed on the rear of seat, the front
wheel load will be reduced, this can cause steering handles shaking. Riding in this way is
dangerous.
It will be much easier to make a turn if rider inclines his body inward when turning. On the other
hand, the rider will feel unstable if his body and the scooter do not incline.
On bumpy, unleveled and slope road, the road condition may change often, driving on these roads
may become very unstable. To drive safely and smoothly, know your road condition before hand,
slow down, and hold the handle firmly with aid of your shoulder.
Suggestion: Do not load objects on the front pedals unnecessarily, to avoid affecting the riding safety
and the operation of steering handle.
CAUTION:
Feeling on the handle is different when the vehicle is with load or without load. Over-load will make
steering handle swing and then influent riding safety. Thus, please be ware of load weight.
CAUTION:
Please do not load cargo or luggage on places where are not designed for loading to prevent danger
and damage.
Do not place rags or similar objects between the storage compartment and engine to avoid engine
seizure because of inadequate engine oil supply.
SUGGESTION
To maximize the scooter’s performance and prolong its service life:
The first month or first 1000km is the wear- in period for the engine and components. Avoid
rapid acceleration, and keep the speed below 60km/hr.
6. USE GENUINE SPARE PARTS
In order to maintain the scooter’s best performance, each part’s quality, material, and machined precision
must conform with the design requirements. “SYM Genuine Spare Parts” were made from the same
high quality materials used for the original scooter. No parts would be sold to the market until they could
meet the designed specifications through sophisticated engineering and stringent quality control.
Therefore, it is necessary to purchase “SYM Genuine Spare Parts” from “SYM Authorized Dealers or
Franchised Dealers” when replacing spare parts. If you buy cheap, or fake substitute parts from the
market, no guarantee can be provided either for the quality or durability. Also, it may result in unexpected
troubles and lower the scooter’s performance.
Always use SYM Genuine Spare Parts to keep your scooters pure blood and to ensure its long
service life.
10
7. Use of each component
Gauges
Model : JET SERIES
Model : MASK SERIES
Fuel Gauge
Turn Signal Indicator
High Bean Indicator
Engine Oil Warning Light
Speedometer
Odometer
Fuel Gauge
Turn Signal Indicator
High Bean Indicator
Engine Oil Warning Light
Speedometer
Odometer
Turn Signal Indicator
7. Use of each component
Model : BS05W SERIES
Model : BL05W6-A / G100P2 SERIES
Model : BK05W-6 SERIES
Fuel Gauge
Turn Signal Indicator
High Bean Indicator
Engine Oil Warning Light
Speedometer
Odometer
Fuel Gauge
Turn Signal Indicator
High Bean Indicator
Engine Oil Warning Light
Speedometer
Odometer
Clock
Turn Signal Indicator
High Bean Indicator
Engine Oil Warning Light
Turn Signal Indicator
Speedometer
Odometer/ Clock
Fuel Gauge
Fuel Warning Indicator
Tachometer
“MODE” Button
“SET” Button
Brightness Button
12
7. Use of each component
CAUTION:
Do not wipe plastic components, e.g. instrument panel, headlight, with organic solvents such as
gasoline…etc to avoid damaging these components.
1. Fuel Gauge
The pointer in this gauge shows how much fuel remains in the tank.
The pointer stays in “E” position when key switch is turned to “OFF.”
When key switch is turned to “ON”, and the “pointer” also in “E” position (red area). Refuel
immediately.
2. Turn Signal Indicator
The left or right Indicator will be flashing according to the operated directions of turn signal light switch
when it is turned on.
3. High Beam Indicator
This indicator comes on with high beam headlight is turned on.
4. Engine Oil Warning Light
Turn the main switch to the “ON” position, if the oil warning light comes on continuously, this indicates
the engine oil level is too low, add oil as required.
WARNING:
To continue drive the vehicle under low oil level condition will result in an engine seizure due to lack
of lubrication of engine parts. It is therefore very important to bring your vehicle to your dealer for an
oil replenishment immediately whenever the warning light comes on continuously.
Use only 2-cycle engine oil meeting Japanese Automobile Standard Organization FC specifications.
Otherwise, this company will not assume any responsibility for damages resulted from using
substandard engine oil.
Recommended oil: SYM EXTRA 2X oil.
5. Speedometer
This shows your speed in kilometers per hour
(km/h) and in mileage per hour (mph).
6. Odometer
This odometer shows the total kilometers this
motor has been driven.
CAUTION:
Observe the speed limit to ensure drive safety.
7-1. Clock
Set time in 24 hour mode.
M” – mode bottom: Press the “M’ bottom, the clock order shows “Time mode”, “Hour setting mode”,
“Minute setting mode”, ”Second setting mode”. Final back to the “time mode”.
S” – set bottom: At “Hour setting mode” or “Minute setting mode” or ”Second setting mode”. Press
the “S” bottom once, numerical can be increase. If keeping on pressing for 2
seconds can accelerate the adjustment. Until to set free the bottom. (At “Second
setting mode”, the colon ”:” in the center will be flash for 1 seconds.
7-2. Clock
Please check the appendix for BK05W-6 series speedometer.P32
13
7. Use of each component
OPERATION OF IGNITION SWITCH
“ON” position
Engine can be started in this position.
Ignition switch key can not be removed.
“OFF” position
Engine is shut off and can not be started in this
position.
Ignition switch key can be removed.
“LOCK” position
Turn the handle all the way to left, then press
down the key and turn the key to the “LOCK”
position on the left.
In this position, the handle is locked and the
key
can be removed.
To unlock, simply turn the key from “LOCK” to
“OFF”.
CAUTION:
Never operate the ignition switch key when the scooter is running. To turn the ignition switch to
“OFF” and “LOCK,” will shut off the electrical system and that may result in a dangerous accident.
Therefore, the ignition switch can only be turned off after the scooter has been completely stopped.
Always remove the key and be sure to take the key away with you after locking the steering handle
before leaving your scooter.
If ignition switch remains in the “ON” position for a prolonged period after the engine has been
stopped, the battery’s capacity will be reduced and this may affect the engine’s start ability.
IGNITION SWITCH
14
7. Use of each component
USE OF BUTTONS
Light Switches
OR
When the switch is turned to this position,
headlight, rear light, instrument panel light,
and position light will go on.
When the switch is turned to this position,
rear light, instrument panel light, and position
light will go on.
When the switch is turned to this position, all
lights will go off. (Depending on Models)
Electrical Starter Button
This is the electrical starter button, it is used
for starting the engine.
When the ignition switch key turns to “ON”
and brake lever hold, and then press this
button down to start engine.
This mechanism is designed for safety.
Thus, the front or rear brake lever must be
hold before using this button so that engine
can be started.
CAUTION:
Release this button immediately after engine
has been started, and never press the button
again to avoid damaging the engine.
Do not use light system. Turn headlight and
turn signal lights to the “OFF” position when
the engine is being started.
Horn Switch
Head light switch
High / Lo
w
Beam Switch
Turn Signal Switch
Electrical Starter Button
Warning signal
switch
Head light switch
Electrical Starter Button
High/Low Beam
Switch
Passing switch
Engine Stop
Switch
15
7. Use of each component
High/Low Beam Switch
This is the high and low beam of headlight switching switch. Press this switch to switch between high
and low beams.
This is for high beam.
This is for low beam. (Please turn to low beam when riding in city)
Turn Signal Switch
Turn signal lights are used when turning left/right or changing lane.
Turn ignition switch to “ON”, and slide the turn signal switch to left or right. Then, the turn signal lights
will flash.
Right-side turn signal light flashing means you intend to make a right turn.
Left-side turn signal light flashing means you intend to make a left turn.
Horn Switch
Press this button down when ignition switch is in the “ON” position, the horn will sound.
CAUTION:
Do not press this button when you are in the no horn area.
SADDLE LOCK
Unlock:
Insert your ignition switch key into the lock on the lower left of the saddle, and turn the key to the right.
Then, the saddle can be lifted up.
Lock:
Press the saddle down and push it locks automatically.
CAUTION:
Please do not put the key into the storage compartment after saddle is unlocked to prevent the key
from being locked inside and can not be removed when the saddle is locked.
Be sure to remove the key after the saddle has been locked
SAFETY HELMET HOOK
Open the saddle, and hook the safety helmet chin belt onto the hook, and then lock the saddle.
CAUTION:
Please do not hang your safety helmet as usual on the hook when driving, to prevent it from
damaging the vehicle and affecting your driving safety.
Engine Stop Switch
Switch to this position to turn off the engine when a state of emergency.
Switch to this position and the engine can be started.
Passing Switch
Turn ignition switch “ON” and press this button down. Then, the high beam of headlight will come on
immediately to warn the driver of the vehicle ahead that you intend to overtake him/her. (For overtaking, high
beam indicator will come on at this time) This button will return to original position after releasing
16
7. Use of each component
STORAGE BOX
This box is located under the saddle.
Maximum load capacity: 10kg.
Do not store valuables in the box.
Please make sure that seat cushion had been locked completely after it was down. Take out valuables
before washing to avoid wetting these objects.
Do not place thermal sensitive objects in the box because of engine’s heat and high temperature.
FUEL TANK CAP
1. Insert ignition switch key into the lock on the fuel tank cap, and turn the key to the right, then the cap
can be removed.
2. Do not fill above the fuel upper limit when refueling.
3. Align the “” mark
4. on the cap with the “” mark on the body, and press down the cap in parallel until a “click” sound is
heard. That means the cap is locked (the ignition key now turns back to the left slightly). To remove
the ignition key, simply turn the key to the left and then remove it.
WARNING:
Main stand should be put down on the ground, engine should be shut off and flames should be
strictly prohibited to ensure safety when refueling.
Do not fill above fuel upper limit when refueling. Otherwise, fuel will flow out through a hole on the
cap that may damage the body’s painting, in serious cases, it may cause a fire to burn down the
scooter.
Make sure the cap has been tighten properly.
BRAKE
Use front and rear wheel brakes simultaneously when braking.
Avoid unnecessary sudden braking.
Using only the front brake or the rear brake increases the risk of falling because the scooter is tend to
pulled to one side.
Avoid brake continuously for a long period of time because that may overheat the brakes and reduce
its braking efficiency.
Slow down and brake early when riding in rainy days on slippery roads. Never apply the brakes
suddenly to prevent skidding and falling.
For Rear Wheel For Front Wheel
17
7. Use of each component
PARKING METHOD
When approaching the parking lot:
1. Turn on the turn signal light early, and pay attention to the vehicles in front, from rear, left and right, then
take the inner lane and approach slowly.
2. Return the throttle valve handle back to its original position, and apply brakes in advance. (Brake light
comes on when braking to warn drivers of vehicles behind.)
When stop completely:
1. Press the turn signal switch back to its original position, and turn the ignition switch key to “OFF”
position to shut off the engine.
2. Get off the scooter from left side after the engine has been stopped, and select a parking place where
the scooter will not interfere with traffic and the ground is level, then put down scooter’s main parking
stand.
3. Hold the steering handle with your left hand, and hold down the front end of saddle or hold the parking
handle on the lower-left side of saddle with your right hand.
4. Press the main parking stand with your right foot, put down the main parking stand firmly on the ground.
To remind you: Lock the steering handle and remove the key after parking to prevent the scooter
from being stolen.
CAUTION:
Park your scooter at a safe place where it will not interfere with traffic.
18
8. Important points and cautions for starting engine
CAUTION:
Please check the engine oil and fuel volume are adequate or not before starting engine.
To start engine the main parking stand must be firmly on the ground and the brake is applied on the
rear wheel to prevent the scooter from moving forward suddenly.
1. Turn ignition switch key to the “ON” position.
2. Apply hand (foot) rear wheel brake.
3. Do not accelerate, press starter button when the
brake is applied.
[We care for you! Before drive off, keep the hand (foot) brake applied on the rear wheel.]
CAUTION:
If engine can not be started after starter motor running for 3~5 seconds, turn the throttle valve handle
1/8~1/4 turns, and then press starter button again for an ease start.
In order to avoid damaging the starter motor, please do not press the starter button continuously over
15 seconds.
It is harder to get the engine started after the scooter has been left idle for a long time or after
refueling only after the fuel has been depleted. Then, it is necessary to press starting lever or starter
button several times, and keep the throttle valve handle at the close position to start the engine.
It may need several minutes to warm up engine if it is a cold start.
Exhaust contains harmful gases (CO), therefore please start the engine at a well ventilated place.
When starting engine with starting lever
Turn the main switch to ON, press the starting lever forcefully by foot with the throttle valve handle at
the close position.
If engine is difficult to start with the starting lever when the engine is cold, rotating the throttle valve
1/8~1/4 turns will make the start easier.
Put the starting lever back to its original position after the engine has been started.
CAUTION:
Firmly support the scooter with the main parking stand before starting the engine with the starting
lever.
Start engine with the starting lever occasionally to prevent it from loosing its function because of
unused for a long time.
1/4
1/8
19
9. The best way to drive off 10.Inspection and maintenance before riding
THE CONTROL OF THROTTLE VALVE HANDLE
Turn on the turn signal light before moving, and make sure no vehicle is coming from behind. Then,
drive off.
During driving, attention should be paid to vehicles ahead and behind and keep highly alert at all
times.
10.INSPECTION AND MAINTENANCE BEFORE RIDING
ROUTINE INSPECTION
Check Items Check Key Points
Engine oil Is there enough engine oil?
Fuel Is it enough? Is it Octane 90 or above
Brake Front Braking condition? [Brake lever free play: 10~20mm]
Rear Braking condition? [Brake lever free play: 10~20mm]
Tires Front Is tire pressure normal? [Standard: 1.75g/cm
2
]
Rear Is tire pressure normal? [Standard: 2kg/cm
2
]
Steering handle Does the handle vibrate abnormally or is difficult to turn?
Speedometer, lights,
and rearview mirror
Is it operated properly? Do lights come on? Can it be seen clearly
from behind?
Tightness of main
components
Are screws, nuts loosen?
Abnormal points Do the previous troubles still exist?
CAUTION:
If any problem founded during routine inspection, correct the problem before using the scooter again,
have your scooter checked and repaired by the “SYM dealer or authorized service personnel” if
necessary.
Deceleration
Acceleration
20
10.Inspection and maintenance before riding
INSPECTION AND REPLENISHMENT OF ENGINE OIL
Inspection:
Turn the main switch to the “ON” position, if the oil warning light comes on continuously, this indicates
the engine oil level is too low, add oil as required.
Check oil tank and oil lines for leakage.
WARNING:
To continue drive the vehicle under low oil level condition will result in an engine seizure due to lack
of lubrication of engine parts. It is therefore very important to bring your vehicle to your dealer for an
oil replenishment immediately whenever the warning light comes on continuously.
Use only 2-cycle engine oil meeting Japanese Automobile Standard Organization FC specifications.
Otherwise, this company will not assume any responsibility for damages resulted from using
substandard engine oil.
Recommended oil: SYM EXTRA 2X oil.
Replenishment:
1. Using the main stand to support the vehicle on a level ground, lift up the saddle, and remove the oil tank
cover.
2. Turn the oil tank cap to the left to remove. Add oil until reaches to the standard level.
3. Screw in the oil tank cap until properly tightened, then reinstall the tank cover and lower the saddle and
press it down until locked.
Add oil note:
Use only 2-cycle engine oil meeting Japanese Automobile Standard Organization FC specifications.
Otherwise, this company will not assume any responsibility for damages resulted from using
substandard engine oil.
When adding oil, do not let foreign materials, dust, dirt enter into the oil system, do not use different
brands mixed oil, because this will affect the engine’s performance.
Do not add oil above the standard level. Clean spilled oil around the oil tank cap.
Be sure to tighten the oil tank cap properly after adding oil.
INSPECTION OF FUEL LEVEL
Firmly support the scooter with its main stand on a leveled ground, turn the main switch to “ON”
position, check if the fuel meter needle moves.
Fuel gauge may be defective or electric circuit disconnected if there is some fuel in the tank, but the
needle does not move. Please drive slowly to an authorized service station to have your scooter
checked.
Note: It is not necessary to start engine to check the fuel level.
21
10.Inspection and maintenance before riding
TRANSMISSION OIL INSPECTION AND CHANGE
INSPECTION:
Use the main stand to support the scooter on a level ground, after the engine stops, wait for 3~5
minutes. Remove the transmission oil infusion bolt, put a measuring glass under the drain bolt, and
remove the drain bolt. Let the oil flows into measuring glass and check for decreased or not. (at
disassembly: 120 c.c. / at change: 100~110 c.c.).
OIL REPLACEMENT:
Stop the engine and use the main stand to support your scooter on a level ground. Remove the
infusion bolt and drain bolt, drain out the oil.
Install the drain bolt and tighten it. Fill new transmission oil (100~110 c.c.), and install the infusion
bolt and tighten it. (make sure that bolts are tightened and check that there’s no leakage.)
Recommend Oil: Genuine SYM HYPOID GEAR OIL (SAE 85W-140).
Use SAE85-90 when outside temperature is below 0.
INSPECTION AND ADJUSTMENT OF BRAKE FREE PLAY
INSPECTION: (Brake lever free play must be checked with the engine shut off.)
Brake lever free play for front and rear wheels
When checking the hand-braking lever for front
and rear wheels, its free play (the stroke of
hand-braking lever from no braking to initial
braking) should be 10~20mm.
It is abnormal if the feel is spongy when holding
the hand-braking lever forcefully.
Adjustment:
The indentation of brake adjustment nut must
be aligned with the pin. (see right figure)
CAUTION:
When free play is between 10~20 mm, check
brake indicators of front and rear wheels. If
the arrow on the brake arm aligned with the
” marked on the brake disk, that means
the brake lining has been excessively worn,
and must be replaced immediately.
Turn the adjustment nut on brake arm of front and rear wheels to adjust the free play of hand-brake
lever.
Hold the hand-brake levers after adjusting with both hands until there is effective brake feeling.
Measure the free play with a rule.
10~20 mm
Pin
Adjustment nut
22
10.Inspection and maintenance before riding
DISK BRAKE INSPECTION [Applicable for model equipped with disc brake.]
Visual Inspection for leakage or damage. If
there is any, take your scooter to SYM
Authorized Dealer or Franchised Dealer for a
check or repair.
Park the scooter on a level ground, and check
if fluid level is under the “LOWER” mark.
Recommended Brake Fluid: WELL RUN
BRAKE OIL (DOT 3).
Check the brake from behind the brake caliper. The brake pad must be replaced with new lining when
the brake pad wear limit reaches the brake disk.
Viewing window
Lower limit
Front wheel drum type
Rear wheel drum type
Adjustment nut
To increase
free play
To decrease free play
To increase
free play
To decrease
free play
Hose connection
Brake pad wear limit grooves
ADDING BRAKE FLUID
Screw
Master
cylinder
Brake caliper
Brake disk
Upper
Diaphragm
Brake fluid
23
10.Inspection and maintenance before riding
CAUTION:
Do not fill above the upper limit when adding brake fluid and avoid dropping on painting or plastic
components to prevent damage.
1. Loosen the screws and remove the master cylinder cover.
2. Wipe clean foreign materials, dirt around the reservoir, being careful not to let foreign materials fall
into the reservoir.
3. Remove the diaphragm plate and the diaphragm.
4. Add brake fluid to upper level.
5. Install the diaphragm plate and the diaphragm, and install the master cylinder cover.
6. Please note the diaphragm direction, and do not let foreign materials fall into the reservoir. And
tighten the master cylinder cover securely.
THROTTLE VALVE HANDLE CLEARANCE ADJUSTMENT
Correct clearance allows throttle vale handle to
rotate 2~6mm.
To adjust, first loosen the fixing nut, then turn
the adjusting nut to the proper position and
securely tighten the fixing nut.
Check Items:
1. Check throttle valve cable to see if it can be
moved smoothly from a closed position to a
wide open position.
2. Rotate steering handle from side to side to
check if the throttle valve cable is interfered.
3. Check to see if the throttle valve cable is
obstructed by other cables preventing it from
being operated smoothly.
INSPECTION AND MAINTENANCE OF BATTERY
This scooter is equipped with a maintenance-free type battery, so it is unnecessary to check and add
electrolyte. Have your scooter checked by SYM Authorized Dealer or Franchised Dealer should any
abnormality is found.
Remove the battery terminals and clean if there
are dirt and corrosion on them.
Battery removal procedures are as follows:
Turn ignition switch “OFF,” and remove negative
cable screw firstly and disconnect the negative
cable. Then, remove positive cable screw and
positive cable.
CAUTION:
Clean the battery posts with warm water if the posts are eroded and have some white powders on
them.
If there is an obvious erosion on the terminals, disconnect the cables, then clean the erosion off with
a steel brush or a piece of sandpaper.
Install battery cable after cleaning and apply a thin coat of grease on the terminals.
Install battery in reverse order of removal.
Negative
Positive
Adjust nut
Lock nut
2~6 mm
24
10.Inspection and maintenance before riding
CAUTION:
This is a closed type battery. Never remove the caps.
In order to prevent electric leakage and self-discharge when the battery sits idle for long periods.
Remove battery from scooter, store it in a well- ventilated and dimly lighted place after the battery has
been fully charged. Disconnect battery’s negative cable if the battery is still kept on the scooter.
If the battery needs to be replaced, replace with a same closed-type battery (Maintenance-Free).
TIRE INSPECTION
Tires should be checked and inflated with the engine shut off.
If a tire’s ground contacting curve is abnormal, check it with an air pressure gauge and inflate it to the
specified pressure.
Tires pressure must be checked with an air pressure gauge when cold.
PLEASE REFER TO SPECIFICATIONS FOR STANDARD TIRE PRESSURE
Visual check tires for frontal and lateral side walls for crack or damage.
Visual check tires for any nails or small stones wedged in the tread.
Check the “tread wear indicator” condition to see if tread groove depth is insufficient.
A tire with a wear bar showing is worn out and should be replaced immediately.
CAUTION:
Abnormal tire pressure, wear, or crack is the most important cause that results in the loss control of the
steering handle and a punctured tire(s).
Tread wear indicator
Crack and damage
Foreign materials (nails or small stones)
25
10.Inspection and maintenance before riding
STEERING HANDLE FRONT SHOCK ABSORBERS INSPECTION
Perform this check with engine shut off and ignition switch key removed.
Visual check front shock absorbers for damage.
Operate steering handle up and down, and check front shock absorbers for noises due to bends.
Check the bolts and nuts of front shock absorbers with wrenches for tightness.
Shake steering handle up & down, left & right, and front & rear to check if it is loosen, has too much
resistance and pulls to one side.
Check steering handle if it is being pulled too tight by the brake cables.
Take your scooter to SYM Authorized Dealer or Franchised Dealer for a check or adjustment if any
abnormal conditions are found.
Figures on the right are for operation checks only
CHECKING AND CHANGING FUSES
Turn off ignition switch, and check fuses if they are intact. Replace the blown fuse with a new one having
the same specified amperage rating (7A). Using a fuse of more than 7 amperes, a brass or iron wire to
replace a blown fuse is strictly prohibited to avoid damaging the electrical system and the circuit.
Remove the battery cover screws, and open the battery cover. Fuses are installed in the fuse box
located by the battery.
Fuses must be firmly secured with wire connectors when replacing.
Use only parts having the specified specification to replace electrical components such as light bulbs.
Using parts not having the specified specifications for replacement may cause the fuse to blow and
over-discharge the battery.
Avoid spraying water directly on or around fuse box when washing the scooter.
Take your scooter to your dealer for an inspection if a fuse is blown by unknown causes.
REMOVE INSTALLATION
Wire
Fuse connectors
Fuse
Press in from above
26
10.Inspection and maintenance before riding
CHECKING THE TURN SIGNAL LIGHTS AND HORN
Turn the ignition switch key to “ON” position.
Turn on the turn signal light switch, and make sure that the front & rear and left & right signal lights
flashes and also check if the warning buzzer sounds.
Check turn signal light covers if they are dirty, crack, or loosen.
Press horn button to check if it works.
CAUTION:
Specified specification bulbs should be used for turn signal lights. Otherwise, the normal operation
of turn signal lights will be affected.
Turn on the turn signal light before turning or switching lane to warn driver of vehicles behind.
Turn off the turn signal light immediately by pressing its button down after using. Otherwise, the
flashing of twin signal lights may confuse the drivers of vehicles behind.
CHECKING THE FRONT AND REAR LIGHTS
Turn the ignition switch key to “ON” position, start the engine and then turn on the front light switch.
Check if front and rear lights come on.
Check the brightness and direction of front light by projecting the light on the wall to see if it is correct.
Check the front light cover if it is dirty, crack, or loosen.
CHECKING THE BRAKE LIGHT
Turn the ignition switch key to “ON” position, hold the hand-braking levers for front and rear wheels.
Check if the brake lights come on.
Check the brake light cover if it is dirty, crack, or loosen.
CAUTION:
Use only specified specification bulbs, do not use bulbs with different specifications to avoid
damaging electrical system, burning out bulbs, and discharging the battery.
Do not modify or add other electrical components to prevent over load or short circuit which may
result in a fire and burn down the scooter in serious cases.
CHECKING FOR FUEL LEAKAGE
Check fuel tank, fuel hoses, and carburetor…etc. for leakage.
CHECING THE LUBRICATION OF BODY’S VARIOUS MECHANISMS
Check the body’s pivot points if they have enough lubrication.
(For example, the pivot points on the main stand, the side stand, and the brake lever…etc.)
27
10.Inspection and maintenance before riding
CHECKING THE SPARK PLUG
Remove the cap of high tension cable. (Use a plug wrench in tool
box to remove the spark plug by turning it counterclockwise.)
Check the electrode if it is dirty or fouled by carbon deposits.
Remove the carbon deposits on the electrode with steel wire, and
clean the spark plug with gasoline, then, wipe dry with a rag.
Check the electrode, and adjust its gap to 0.6~0.7mm. (Check it
with a feeler gauge)
Hand tight the spark plug as far as it can go and then tighten it
another 1/2~3/4 turns with a wrench.
WARNING: The engine is very hot after running. Pay attention
not to get burned.
Use only spark plugs suitable for the engine specifications of
this scooter recommended by the manufacturer. (Refer to
specifications.)
CHECKING THE AIR CLEANER
DISASSEMBLE PRCEDURE
1. Remove the screw of air cleaner cover.
2. Remove the air cleaner cover and then the
cleaner’s element.
3. Clean or replace the element.
(For checking interval please refer to
maintenance schedule.)
4. Refer to figures shown on the right for air
cleaner element cleaning steps.
Procedures for cleaning air cleaner element:
1.cleam. 2.squeeze dry.
3.soak in engine oil. 4.squeeze dry
ASSEMBLE PRCEDURE
Assemble the air cleaner in reverse order of disassemble.
CAUTION:
Dust deposit is one of the major causes of reducing output horsepower and increasing fuel
consumption.
Change the air cleaner element more frequently to prolong the engine’s service life if the scooter is
driven on dusty roads very often.
If air cleaner is installed improperly, dust will be absorbed into cylinders, which may cause a
premature wear and reducing output power and engine life.
Be careful not to soak the air cleaner when washing the scooter. Otherwise, it will cause engine
hard to start.
0.6~0.7mm
28
11.when there is an abnormal condition or a trouble
DIAGNOSIS WHEN ENGINE DOES NOT START
1.Does the ignition switch key turn to “ON” position? 2. Is there fuel in the fuel tank?
3. Is the rear or front wheel brakes being hold when
pressing starting button?
4.Turn the ignition switch key “ON”, and press horn
button. The fuse may blow if horn not sounding.
Please go to SYM authorized dealer or franchised dealer immediately if there are no problems on
above conditions and engine still can not be started.
For Front WheelFor Rear Wheel
The turn signal light switch
Horn button
12.periodical maintenance schedule
29
Maintenance
kilometer
300KM
Every
1,000KM
Every
3,000KM
Every
6,000KM
Every
12,000KM
Item
Check Items
Maintenance
Interval
NEW 1 Month 3 Months 6 Months 1 Year
Remarks
1 Air cleaner element(Remark) I C C R
2 Fuel filter I I R
3 Tire, pressure I I
4 Battery I I
5
Brake and brake clearance
checking
I I I I I
6 Spark plug I I R
7 Carburetor(idle speed) I I
8 Ignition timing I I I I I
9 Steering bearing and handles I I
10 Check Transmission for leakage I I
11 Check crankcase for leakage I I
12 Transmission Oil R Replacement for every 5,000KM(5 Months)
13 Drive Belt/roller I R
14 Light / electrical / meters I I I I I
15 Fuel tank switch and lines I I
16 Throttle valve operation and cable I I
17 Engine bolts and nuts I I
18 Cylinder head, cylinder, and piston I
19 Exhaust system/cleaning carbon I
20 Greasing on chassis L L
21 Front/rear suspension I I
22 Main/side stands I I/L
23 Clutch disk I
24 Operation of oil pump rod I I
25 Brake mechanism/brake lining (pad) I I
26 Bolts/nuts for each components I I
The above maintenance schedule is established by taking the monthly 1,000 kilometers as a
reference which ever comes first.
Have your scooter checked and adjusted periodically by your SYM Authorized Dealer or Franchised
Dealer to maintain the scooter at the optimum condition.
Code: I ~ Inspection, cleaning, and adjustment R ~ Replacement
C ~ Cleaning (replaced if necessary) L ~ Lubrication
Remark: 1. Clean or replace the air cleaner element more often when the scooter is operated on dusty
roads or in the Heavily- polluted environment.
2. Maintenance should be performed more often if the scooter is frequently operated in high
speed and after the scooter has accumulated a higher mileage.
13.Specificatione
30
Model
Item Specification
JET Euro50
BL05W6
JET 50α RED DEVIL50 BL05WA
Length ( mm) 1,785
Width ( mm) 680
Height ( mm) 1,125 1,115
Wheel base ( mm) 1,275
Net Weight 94 kg
Type 2- stroke single cylinders engine
Fuel Unleaded gasoline (octane 90 or higher)
Cooling type Air-cooled
Bore
Ø 39 mm
Stroke
41.4 mm
Displacement
49.4 cc.
Compression ratio 7.2:1
Max. HP
3.2 kW / 7,000 rpm 2.6 kW/6,000rpm
Max. torque
4.6 Nm / 6,500 rpm
4.2Nm/5,500rpm
Starting methods Electrical & kick type
shock absorber Front :Telescope / Rear : Unit swing
Clutch Dry/auto centrifugal clutch
Transmission C.V.T., auto speed change
Front tire 120/70–12
Rear tire 130/70-12
Tire pressure Front: STD 1.75kg/cm
2
/ Rear: STD 2.0 kg/cm
2
Front brake (Disc type) (Ø 190 mm)
Rear brake (drum type) (Ø 110 mm)
Front light bulb(high, low) 12V15W X 2 12V35W/35W X 1
12V35W X 2
Brake light bulb(tail light) 12V5W / 21W X 2
Turn signal light bulb 12V 10W
Engine oil tank capacity 1.2 L
Transmission oil capacity 120 cc. (100~110 cc. for change)
Fuel tank capacity 6.3 L
Fuse 7A
Spark plug BR 8HSA
Battery capacity(MF battery) 12V 4Ah
Air cleaner Sponge type
31
13.Specificatione
Model
Item Specification
JET Sport X 50
BK05W
MASK 50
BF05W
RS 50
BS05W
G100-P2
Len
g
th
(
mm
)
1,840 1,835 1,870 1,785
Width
(
mm
)
690 650 700 630
Hei
g
ht
(
mm
)
1,120 1,110 1,130 1,125
Wheel base
(
mm
)
1,275 1,280 1,335 1,275
Net Wei
g
ht
98 kg 94 kg 108 kg 97 kg
T
y
pe
2- stroke single cylinders engine
Fuel
Unleaded gasoline (octane 90 or higher)
Coolin
g
t
y
pe
Air-cooled
Bore
Ø 39 mm Ø 51 mm
Stroke
41.4 mm 49.6 mm
Displacement
49.4 cc. 101.3 cc.
Compression ratio
7.2:1 6.3:1
Max. HP
2.6 kW/6,000rpm 3.2 kW/6,500rpm 2.8 kW/6,000rpm 6.21 ps/6,250rpm
Max. torque
4.2 Nm/5,500rpm 5.1 Nm /6,000rpm
4.58 Nm/5,000rpm 0.76 kg-m/5,500rpm
Startin
g
methods
Electrical & kick type
shock absorbe
r
Front :Telescope / Rear : Unit swing
Clutch
Dry/auto centrifugal clutch
Transmission
C.V.T., auto speed change
Front tire 120/70–12 100/90-12(59J) 120/70-12
Rear tire 130/70-12 130/70-12(59J) 130/70-12
Tire pressure
Front: STD 1.75kg/cm
2
/ Rear: STD 2.0 kg/cm
2
Front brake
(
Disc t
y
pe
)
(Ø 190 mm) (Ø 273 mm) (Ø 190 mm)
Drum (Ø 110 mm)
Rear brake
Disc (Ø 160 mm)
Drum (Ø 110 mm)
Front light bulb(high, low)
12V35W/35W X 1 12V25W/25W X 2
Brake light bulb(tail light)
LED 12V5W / 21W X 1 12V5W/21W X 2
Turn signal light bulb
12V 10W
Engine oil tank capacity
1.2 L
Transmission oil capacity
120 cc. (100~110 cc. for change)
[ winter :SAE 85W-90 ; summer : SAE85W-140]
Fuel tank capacity
6.3 L 7.5 L 6.3 L
Fuse
15A 7A
Spark plug
BR 8HSA BR 6HSA
Battery capacity(
MF
battery)
TTZ 7SL 12V 4Ah 12V 3Ah 12V 4Ah
Air cleaner
Sponge type
SYM 2006/04
14. Postscript
32
FUNCTION Set time in 12 hour mode
There are three buttons on the speedometer, explanation as below :
1. SET button “S”:
a. Under TRIP mode, press “S” button continuously to reset the TRIP kilometer readings.
b. Under ODO mode and the vehicle is standing still, press SET for above 2 seconds to enter CLOCK
mode. Press “S” button shortly to enter time setting mode.
CLOCK + HOUR CLOCK + MIM (10 MIN.) CLOCK + MIN ( 1 MIN.)
(flashing) (flashing) (flashing)
c. Under CLOCK mode, press “M” button shortly to increase the readings, once per one time.
d. Under time setting mode, press “S” button continuously to exit this setting mode.
2. MODE button “M”:
a. Press “M” button to change between “TOTAL””TRIP””CLOCK” modes.
TOTAL TRIP CLOCK
b. When the engine oil lamp lights on, press “M” button continuously to put it out.
c. The readings will remain there after main switch is turn off.
3. Brightness button”
BRIGHTEST BRIGHTER BRIGHT DIM
a. Press
” button to adjust the brightness.
b. The setting will remain there after main switch is turn off.
Under TOTAL mode, press “S” button continuously to change between “kilometer” & ”mileage”
readings.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sym JET EVO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sym JET EVO in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info