11965
18
Zoom out
Zoom in
Previous page
1/56
Next page
- 18 - EN
1C29
CHANNEL SET UP
Make sure ...
Press the POWER button to turn on the TV/VCR/DVD.
1 Select “CHANNEL SET UP”
Press the SETUP button on the
remote control.
Press the Arrow button
K or L to
point to “CHANNEL SET UP”.
Then, press the ENTER button.
2 Begin auto ch programming
Press the Arrow button K or L to
point to “AUTO CH PROGRAM-
MING”.
Then, press the ENTER button.
The tuner scans and memorizes all
the active channels in your area.
3 After scanning
The tuner stops on the lowest memorized channel.
When AUTO CH PROGRAMMING is activated
where there is no TV signal input, “NO TV SIG-
NALS” will appear on the display after the com-
pletion of the channel scanning.
The TV/VCR/DVD may recognize TV channels to
be CATV channels by the receiving conditions. In
this case, try auto ch programming again in the fine
receiving conditions.
– M E N U –
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
B CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
– CHANNEL SET UP –
ADD / DELETE CH (CATV)
B AUTO CH PROGRAMMING
The channels you no longer receive or seldom watch
can be deleted from the memory. (Of course, you
can add the deleted channel into the memory again.)
1 Select “CHANNEL SET UP”
Press the SETUP button on the
remote control.
Press the Arrow button
K or L to
point to “CHANNEL SET UP”.
Then, press the ENTER button.
2 Select “ADD/DELETE CH”
Press the Arrow button K or L to
point to “ADD/DELETE CH”.
Press the ENTER button.
3 Enter the desired channel number
Press the Arrow button K or L
until your desired channel number
appears. (You can also use the
number buttons or the CHANNEL
K or L button to enter it)
(Example: CH8)
When selecting cable channels which are higher
than 99, press the +100 button first, then, press the
last two digits. (Example: to select channel 125,
first press the +100 button then press “2” and “5”).
You must proceed single-digit channel numbers
with a zero (Example: 02 ... 09).
4 Delete (or add) it from (into) memory
Press the ENTER button. The channel number
changes to light red. The channel is deleted from
memory.
To delete another channel, repeat steps [3] and [4].
If you press the ENTER button again, the channel
is memorized again.
5 Exit the channel setup mode
Press the SETUP button on the remote control to
returns to TV mode.
NOTE: To confirm that channel(s) has been deleted
or added, press the CHANNEL
K or L button.
DELETING (OR ADDING)
CHANNEL
Added channel: Light blue.
Deleted channel: Light red.
– M E N U –
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
B CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
– CHANNEL SET UP –
B ADD / DELETE CH (CATV)
AUTO CH PROGRAMMING
08
ADD / DELETE
You can program the tuner to scan all the channels
you receive in your area.
NOTE: Channel memory programming is NOT
needed when connected to a cable box or satellite
box. Just select the TV/VCR/DVD channel selector
to the output channel of the cable box or satellite box
(Ex CH3). Then select the channel to be viewed on
the Cable Box or Satellite Box.
TV/VCR
TV/VCR
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sylvania 6720FDE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sylvania 6720FDE in the language / languages: English as an attachment in your email.

The manual is 1,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info