Manual Sygonix TX 2 (page 3 of 8) (English, German, Dutch, French)

565040

Zoom out

Zoom in

1/8

The home technology brand for the entire house. More information at www.sygonix.com

Operating instructions

Thermostat “tx.2“, AP

Intended use

The product is used for the temperature control in living areas and ofﬁ ces.

Depending on the device connected, you can switch between the heating or cooling

function using a sliding switch.

The other sliding switch is used to select the overnight temperature reduction (night

setback) or to turn it on or off (2 °C or 5 °C can be selected).

An LC display indicates the room temperature and the operating mode.

Always observe the safety instructions and all other information included in these op-

erating instructions!

Any other use than that described above may damage the product. Moreover, this

may give rise to hazards such as short-circuiting, ﬁ re, electric shock, etc. No part of the

product may be modiﬁ ed or converted!

This Product Meets Legal, National and European Requirements. All names of com-

Package Contents

• Thermostat

• Operating Instructions

Explanation of the Symbols

The lightning symbol indicates a health hazard, e.g. electric shock.

This symbol indicates speciﬁ c risks associated with handling, function and

use.

Safety Instructions

Read the complete operating manual carefully before using the product,

as it contains important information about the correct installation and

operation.

The warranty will be void in the event of damage caused by failure to ob-

serve these safety instructions! We do not assume any liability for any

consequential damage!

We do not assume any liability for material and personal damage caused

by improper use or non-compliance with the safety instructions! The

warranty will be void in such cases!

Caution!

This device should be installed only by people with relevant electrotech-

nical knowledge and experience!

With an improper installation, you risk:

- Your own life;

- The life of the user of the electrical system.

With an improper installation, you risk severe material damage, e.g. through

ﬁ re. Yo u face the risk of personal liability for damage to people and material.

Contact an electrician!

• The unauthorised conversion and/or modiﬁ cation of the product is not al-

lowed for safety and approval reasons (CE).

• The product is not a toy and must be kept out of the reach of children! There

is a risk of a lethal electric shock!

• The product may only be operated on the mains voltage (see section “Tech-

nical Data”). Never try to operate the product at another voltage as this will

cause its destruction.

• This product is only to be installed and used in dry conditions indoors. The

product must not get damp or wet as this may damage it; danger of a fatal

electric shock!

• Do not use this product in rooms or under adverse ambient conditions

where combustible gases, vapours or dust are or may be present! There is a

risk of explosion!

• The product must not be exposed to extreme temperatures, strong vibra-

tions or heavy mechanical stress.

• If you have reason to assume that safe operation is no longer possible, dis-

connect the product immediately and secure it against inadvertent opera-

tion. After this, let an expert check the product.

It can be assumed that safe operation is no longer possible if:

- the product shows visible signs of damage,

- the product does not work at all or works poorly (ﬂ ickering light, leaking

smoke or a smell of burning, the light ﬂ ickers, audible cracking noises,

discolouration to the product or the adjacent surfaces.)

- the product was stored under unfavourable conditions

- it was exposed to heavy loads during transport

• Do not leave packaging material carelessly lying around since it could be-

come a dangerous plaything for children.

• In commercial institutions, the accident prevention regulations of the Em-

ployer’s Liability Insurance Association for Electrical Systems and Operating

Facilities are to be observed!

• If you have any questions that are not answered in this manual, please con-

tact our technical service or another specialist.

Preparations for connection and installation

• The device must be voltage-free during installation and connection.

Turn the power off and ensure that none of the poles is carrying a current by remov-

ing the electric circuit's fuse, or switching off at the circuit breaker. Secure it against

unauthorised reconnection, e.g., with a danger sign. In addition, switch off the as-

sociated ground fault circuit interrupter (breaker).

• Check that the mains cable is free of current e.g. with an appropriate tester.

• Choose a suitable place for installation. In order to ensure a correct functioning of

the thermostat, it must be mounted so that it is not located near to heating appli-

ances, windows, doors etc. Keep the thermostat away from draught too.

Don't mount the thermostat behind furniture or curtains.

Since the exterior walls of buildings are usually colder than the interior ones (de-

pending on the insulation of the building), the thermostat should not be mounted

there either.

Wall heaters function with air convection. In the process, the warm air rises from the

heater, cools down slowly and decreases on the other side of the room. Thus, the

ideal location for the installation of the thermostat would be the wall opposite to the

heater. The ideal mounting height is approx. 1.5 m.

Installation and Connection

Observe the chapter “Safety instructions” and the chapter “Prepara-

tions for connection and installation”.

• First switch off the mains voltage to all poles.

• Remove the wall mounting plate on the back of the device by unscrewing the two

fastening screws at the bottom edge.

• You will ﬁ nd the temperature sensor on the rear of the

room temperature regulator, which is attached by two

spring clips (see picture right).

If desired, you can replace these internal sensors with

an external sensor (this is not included in the room

temperature regulator package; it can be ordered se-

parately).

Pull the two-poled spring clips from the contact pin, to

attach easily, and then loosen the two screws, which

attach the sensor and take out the sensor. Keep this

for later use.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sygonix TX 2 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,3 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sygonix TX 2 Manual

Product: