53171

Sweex IEEE 802.11g Wireless Router Manual

22
Zoom out
Zoom in
Previous page
1/42
Next page
802.11g Wireless Router User’s Manual
21
Enable Wireless. If you disable the wireless, wireless devices cannot connect to the wireless router.
Mode. This field determines which data communication protocol will be used. You can keep the
default setting “MIXED” if you have 802.11g and 802.11b devices in the network. “G_ONLY”
dedicates the wireless router to communicating with the 802.11g wireless devices exclusively.
“B_ONLY” dedicates the wireless router to communicating with the 802.11b wireless devices
exclusively.
ESSID. The Extended Service Set Identifier (ESSID) is the network name shared among all devices in
a wireless network. The ESSID must be identical for all devices in the wireless network. It is
case-sensitive and must not exceed 32 alphanumeric characters, which may be any keyboard character.
Make sure this setting is the same for all devices in your wireless network.
Channel. This field determines which operating frequency will be used. It should not be necessary to
change the wireless channel unless you notice interference problems with another nearby access point
or wireless router.
Beacon Interval. The default value is 100. Enter a value between 1 and 65,535 milliseconds. The
Beacon Interval value indicates the frequency interval of the beacon. A beacon is a packet broadcast by
the Router to synchronize the wireless network.
RTS Threshold. This value should remain at its default setting of 2432. The range is 256 ~ 2432 bytes.
Should you encounter inconsistent data flow, only minor modifications are recommended. If a network
packet is smaller than the present RTS threshold size, the RTS/CTS mechanism will not be enabled.
The Router sends Request to Send (RTS) frames to a particular receiving station and negotiates the
sending of a data frame. After receiving an RTS, the wireless station responds with a Clear to Send
(CTS) frame to acknowledge the right to begin transmission.
Fragmentation Threshold. This value should remain at its default setting of 2346. The range is 256 ~
2346 bytes. It specifies the maximum size for a packet before data is fragmented into multiple packets.
If you experience a high packet error rate, you may slightly increase the Fragmentation Threshold.
Setting the Fragmentation Threshold too many may result in poor network performance. Only minor
… 22 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sweex IEEE 802.11g Wireless Router at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sweex IEEE 802.11g Wireless Router in the language / languages: English as an attachment in your email.

The manual is 2,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info