556672

Suunto X6M Manual

21
Zoom out
Zoom in
Previous page
1/63
Next page
EN
1
Suunto X6/X6m
USER’S GUIDE
EN
2
TABLE OF CONTENTS
1. GENERAL INFORMATION ......................................................................................5
1.1. Care and Maintenance ..........................................................................5
1.2. Water Resistance ..................................................................................6
1.3. Battery Replacement .............................................................................6
1.4. After sales service .................................................................................8
2. HOW TO USE YOUR SUUNTO X6/X6M ................................................................9
2.1. Display .................................................................................................9
2.1.1. Mode Symbols ..........................................................................9
2.1.2. Function Symbols ...................................................................10
2.2. Buttons ...............................................................................................11
2.2.1. Short and Long Press ............................................................. 11
2.2.2. Start Button ............................................................................11
2.2.3. Stop/CL Button .......................................................................11
2.2.4. Suunto Button .........................................................................12
2.2.5. Arrow Buttons .........................................................................12
2.2.6. Button Lock ............................................................................13
2.3. Menus ...............................................................................................13
2.3.1. Basic Menu Structure .............................................................13
2.3.2. Navigating in Menus ...............................................................14
3. MODES ...............................................................................................15
3.1. General Information ............................................................................15
3.2. Time Mode ..........................................................................................16
3.2.1. Main Display ...........................................................................16
3.2.2. Alarm ......................................................................................16
3.2.3. Time ........................................................................................18
3
3.2.4. Date ........................................................................................19
3.2.5. General ...................................................................................20
3.2.6. Units .......................................................................................22
3.3. Compass Mode ...................................................................................25
3.3.1. Main Display ...........................................................................25
3.3.2. Use .........................................................................................26
3.3.3. Altitude/Sealevel .....................................................................27
3.3.4. Compass ................................................................................28
3.4. Weather Mode .....................................................................................30
3.4.1. Main Display ...........................................................................30
3.4.2. Use .........................................................................................31
3.4.3. Sealevel ..................................................................................31
3.4.4. Alarm ......................................................................................32
3.4.5. Memory ..................................................................................32
3.5. Hiking Mode ........................................................................................33
3.5.1. Main Display ...........................................................................33
3.5.2. Logbook ..................................................................................34
3.5.3. Use .........................................................................................38
3.5.4. Altitude ...................................................................................38
3.5.5. Alarms ....................................................................................38
3.6. Hiking Chrono .....................................................................................40
3.6.1. Main Display ...........................................................................40
3.6.2 Memory ..................................................................................41
3.6.3. Altitude ...................................................................................44
3.6.4. Use .........................................................................................44
3.6.5. Reminder ................................................................................44
4
3.6.6. Effect of air temperature on altitude measurement ................46
4. ADDITIONAL FEATURES .....................................................................................50
4.1. PC Interface ........................................................................................50
4.1.1. Transferring Data ....................................................................50
4.1.2. Suunto Activity Manager Features .........................................51
4.2. SuuntoSports.com ...............................................................................53
4.2.1. System Requirements ............................................................54
4.2.2. SuuntoSports.com Sections ...................................................54
4.2.3. Getting Started .......................................................................56
5. TECHNICAL DATA ...............................................................................................57
6. COPYRIGHT AND TRADEMARK NOTICE ..........................................................58
7. CE ...............................................................................................58
8. LIMITS OF LIABILITY AND ISO 9001 COMPLIANCE ..........................................59
9. DISPOSAL OF THE DEVICE ................................................................................59
5
1. GENERAL INFORMATION
The Suunto X6/X6M Wristop Computer is a reliable high-precision electronic instrument
that is intended for recreational use. Outdoor enthusiasts who enjoy sports such as
mountain climbing, hiking and biking can rely on the Suunto X6/X6M’s accuracy.
NOTE: The Suunto X6/X6M should not be substituted for obtaining measurements
that require professional or industrial precision and should not be used to obtain
measurements when skydiving, hang gliding, paragliding, gyrocopter riding and flying
a small aircraft.
1.1. CARE AND MAINTENANCE
Only perform the procedures described in this manual. Never attempt to disassemble
or service your Suunto X6/X6M. Protect your Suunto X6/X6M from shocks, extreme
heat and prolonged exposure to direct sunlight. If not in use, store your Suunto X6/X6M
in a clean, dry environment at room temperature.
The Suunto X6/X6M can be wiped clean with a lightly moistened (warm water) cloth.
If there are stubborn stains or marks, you can apply mild soap to the area. Do not
expose the Suunto X6/X6M to strong chemicals such as gasoline, cleaning solvents,
acetone, alcohol, insect repellents, adhesives and paint, as they will damage the unit’s
seals, case and finish. Keep the PC interface contacts clean with e.g. a toothbrush.
Make sure the area around the sensors is kept free of dirt and sand. Never insert any
objects into the sensor openings.
6
1.2. WATER RESISTANCE
Suunto X6/X6M is water-resistant. Its water resistance is tested to 100m/330ft according
to ISO 2281 standard (www.iso.ch). This means that you can use your Suunto X6/X6M
for swimming and other water sports activities but it must not be used for scuba diving
or freediving.
To maintain water resistance and to ensure that the warranty remains valid, it is strongly
recommended to have all service, except for battery change, done by authorized Suunto
service personnel.
NOTE: Never push the buttons while swimming or in contact with water. Deliberate
or unintentional pressing of the buttons while the unit is submerged could cause the
unit to malfunction.
1.3. BATTERY REPLACEMENT
The Suunto X6/X6M operates on a 3-Volt lithium cell, type: CR 2032. The life expectancy
is approximately 12 months in Time/Weather modes.
A low-battery warning indicator is activated on the display when approximately 5–15
percent of the battery capacity is still available. When this occurs, you should replace
the battery. However, extremely cold weather may activate the low battery warning
indicator, even though the battery is still fully operational. If the battery warning indicator
is activated in temperatures above 10°C (50°F), replace the battery.
NOTE: Heavy use of the backlight, altimeter and compass will significantly reduce
battery life.
7
REPLACING THE BATTERY
Make sure that you have purchased an original Suunto battery kit (including battery
and battery lid with installed O-ring) before you start replacing the battery.
1. Insert a coin into the slot or a Suunto battery-opening coin into the slot or holes
located in the battery compartment cover on the backside of your device.
2. Turn the coin counterclockwise until it is aligned with the open position marker. Then,
turn and lift the cover with the coin simultaneously, until the cover opens.
3. Remove the battery compartment cover and the old battery carefully. Avoid damaging
the contact plate.
8
4. Carefully clean the inside sealing surface of the battery compartment before placing
your new battery in the compartment.
5. Place the new battery into the battery compartment with the positive side facing up.
Gently slide the battery underneath the contact plate, ensuring that the contact plate
does not break or bend out of place.
6. Place the new battery compartment cover on top of the battery compartment, aligning
the position marker on the cover with the open position marker on the backside of
your device.
7. Using the coin, gently press and turn the cover clockwise, until the position marker
on the cover is aligned with the close position marker on the back.
NOTE: When the battery has been replaced, ensure that the battery compartment is
correctly closed. This helps your Suunto device remain water-resistant. Careless battery
replacement may void the warranty.
NOTE: Heavy use of the backlight, especially in the Night Use setting, will significantly
reduce battery life.
1.4. AFTER SALES SERVICE
If a claim under warranty appears to be necessary, return the product, freight prepaid,
to your Suunto dealer who is responsible for having your product repaired. Include your
name and address, proof of purchase and/or service registration card, as required in
your country. The claim will be honored and the product repaired or replaced at no
charge and returned in what your Suunto dealer determines a reasonable amount of
time, provided all necessary parts are in stock. All repairs made, not covered under
the terms of this warranty, will be made at the owner’s expense. This warranty is non-
transferable from the original owner.
9
If it is not possible to contact your Suunto dealer, contact your local Suunto distributor
for further information. You can locate your local Suunto distributor from www.suunto.
com.
2. HOW TO USE YOUR SUUNTO X6/X6M
2.1. DISPLAY
When your Suunto X6/X6M leaves the factory, it is in sleep mode, with the display
empty. Press any button to activate the Suunto X6/X6M. The text “
defrag of memory”
is displayed and after a few seconds the Time mode is activated. Later on, you can
select which mode is displayed. For information about setting the correct time, refer
to chapter 3.2.3.
In addition to mode-specific information, the Suunto
X6/X6M display includes several symbols.
2.1.1. Mode Symbols
The mode symbols on the left of the display indicate
the active mode:
Time
Hiking
Compass
Hiking chrono
Weather
10
2.1.2. Function Symbols
The function symbols indicate that either a function has been activated (such as Alarm)
or something needs to be done (battery symbol). The function symbols are:
Alarm
Active, when at least one of the alarms is on.
Weather/Altitude alarm
Active, when weather alarm, altitude alarm or asc/dsc alarm is on.
Logbook
Active, when the logbook is recording data.
Chrono
Active, when the chrono is on and recording data to a file.
Use alti/baro
Indicates that the air pressure sensor is used as a barometer and the altitude reading
is fixed.
Active when you select the air pressure to be displayed as weather information. In this
case the altitude reading in Hiking, Chrono and Compass modes is fixed. For more
information refer to chapter 3.3.2.
Battery
Active, when 5–15 percent of the battery capacity is left and the battery should be
replaced.
Button Lock
Active, when the button lock has been activated.
11
2.2. BUTTONS
2.2.1. Short and Long Press
The buttons may have different functions depending on how long you press them.
The ordinary
press or short press means that the button is pressed quickly.
The long press means that the button is pressed for more than 2 seconds.
2.2.2. Start Button
Short press
• In Chrono mode, it starts timing and records
and displays the intermediate times.
• In Hiking mode, it records the mark points
(altitude and time).
Long press
• Activates the backlight when the backlight
is not set to the off position. The backlight
stays on as long as a selection is active and
5 seconds after the last selection. For more
information about backlight settings, refer to
chapter 3.2.5.
2.2.3. Stop/CL Button
Short press
• Returns to the previous menu level or to
the previous selection without accepting the
selection.
12
• In the Chrono mode, it stops timing.
• In the main displays, it acts as a shortcut button, that toggles the lowest field of the
main display between three different alternatives. The selection stays active even if
the mode or menu level is changed.
Long press
• Returns to the main display of the current mode without accepting the last selection.
In the Chrono mode, it resets the stopwatch.
2.2.4. Suunto Button
Short press
• Scrolls to a lower menu level.
• Accepts the selections made with arrows and moves to the next phase.
• After the last selection, it returns to the Set menu.
• With two possible selections (e.g. light On/Off), it activates the selection and accepts
the selections made with arrows.
Long press
• Returns to the main display of the current mode and accepts the selection.
• With two possible selections (e.g. light On/Off), it accepts the selection and returns
directly to the main display of the current mode.
2.2.5. Arrow Buttons
Short press
• Scrolls from one mode to another.
• Scrolls the menus up and down, and logbook and memory forward and back.
• Changes the values. The
up arrow increases the value and the down arrow decreases
13
the value.
• With two possible selections (e.g. light On/Off), both arrows change the value.
2.2.6. Button Lock
The button lock prevents you from pushing the buttons. If the button lock is activated
and you try to press a button, the message “unlock press suunto” is displayed.
Activating the button lock
To activate the button lock:
1. Press Suunto. The Suunto X6/X6M switches to the Function menu.
2. Press
Start within 2 seconds. The buttons are locked and the Suunto X6/X6M switches
to the main display of the current mode.
Deactivating the button lock
To deactivate the button lock:
1. Press Suunto. The following text is displayed: “now press start”.
2. Press
Start within 2 seconds.
2.3. MENUS
2.3.1. Basic Menu Structure
The menus are organized hierarchically under the modes. When you select a mode,
its main display appears. When you press Suunto in the mode’s main display, the
mode’s Function menu is displayed. The Function menu includes several functions
and all the functions include sub-functions or settings. This is called the hierarchical
menu structure.
14
2.3.2. Navigating in Menus
You can scroll the menu items with the up and down arrow buttons on the right side of
the Suunto X6/X6M. Three menu items are displayed at the same time. The menu item
that is currently active and can thus be selected is displayed in reversed color. On the
right side of the display is an indicator bar showing the total number of menu items. The
number of the active menu item is displayed next to the indicator bar.
To move deeper into the hierarchy, select a menu item and press Suunto. To return one
step up in the hierarchy, press Stop/CL. Remember that if you just press Stop/CL the
changes are not saved—first you have accepted them with the Suunto button.
If you want to return directly to the main display of the active mode, press for more than
2 seconds either Suunto (saves the changes) or Stop/CL (discards the last change).
Suunto X6/X6M has been designed to guide you as much as possible when you
navigate in the menus. When you perform a function, the Suunto X6/X6M often returns
automatically to the menu that you are likely to use next. Also, for example, if you try
to do something that is impossible, the Suunto X6/X6M first displays a message and
then automatically recommends a function in reversed color to help you to use the
functions.
15
3. MODES
3.1. GENERAL INFORMATION
Suunto X6/X6M has five modes: Time, Compass, Weather, Hiking and Hiking Chrono.
The symbols for each mode are displayed on the left of the Suunto X6/X6M display.
When you select a mode, the active mode indicator appears on the display next to the
symbol of the selected mode. If the icons are set to on, they also display the active
mode.
To select a mode, press either the up or down arrow while in the main display of any
mode and scroll the modes. During scrolling, the icon of the selected mode and its
name appear on the display. When you stop scrolling, the icon stays for a little while
and then the main display of that mode opens automatically.
NOTE: In addition to the active mode indicator, the Use indicator can also be displayed
next to the Compass or Weather mode symbols. If the Use is set to Alti, the indicator
is next to the Compass mode symbol and if the Use is set to Baro, the indicator is next
to the Weather mode symbol. For more information about the Alti or Baro Use, refer to
chapter 3.3.2.
16
3.2. TIME MODE
3.2.1. Main Display
When you select the Time mode, the main display opens. The main display has three
rows:
Date
The first row displays the date in the selected format. For more information about
changing the date format, refer to chapter 3.2.6.
Time
The second row displays the time in the selected format. For more information about
changing between 12- and 24-hour display, refer to chapter 3.2.6.
Shortcuts
The third row displays alternatively the weekday, seconds or dual time. To change the
displayed information, press Stop/CL.
• Weekday: Displays the current weekday.
•
Seconds: Displays seconds.
•
Dual time: Displays the dual time.
3.2.2. Alarm
You can set altogether three independent alarms. In addition to the time, you can define
a date when the alarm sounds. If you do not define the date, the alarm will sound daily,
as long as it is set to on.
When the alarm is set, the alarm symbol appears on the Suunto X6/X6M display.
17
Activating alarms
To activate an alarm:
1. In the Function menu, Alarm is already as the first menu item. Select it by pressing
Suunto. The alarm menu displays the status of the alarms. When you open the menu
for the first time the alarm indicators are set to off as default.
2. Scroll to the alarm you want to set and press
Suunto. The alarm information is
displayed and the On/Off indicator is activated. When you open the alarm information
for the first time, the time is 00:00 or 12:00 am.
3. Press either the
up or down arrow to change the alarm status to on.
4. Press
Suunto. The alarm indicator changes to on and the hour selection is
activated.
5. Set the correct
hour with the arrow buttons and press Suunto. The minute selection
is activated.
6. Set the correct
minutes with the arrow buttons and press Suunto.
7. If you want the alarm to sound
every day, accept the dd.mm format by pressing
Suunto. (A long press takes you back to the main display. Two short presses first
activate the mm field and then take you to the Function menu.) The alarm is set to
sound every day and you return to the Function menu.
8. If you want to set the alarm for a specific date, set the day and month in the
dd and
mm fields with the arrow buttons and accept the date by pressing Suunto. The alarm
is set to sound only once on the selected date and you return to the Function menu.
To set the alarm back to daily function, activate the mm field and set its value back
to mm with the arrow buttons and accept the setting with Suunto.
18
Deactivating alarms
To deactivate the alarm:
1. In the Function menu, scroll to
Alarm and press Suunto.
2. Scroll to the alarm you want to set off and press
Suunto. The alarm information is
displayed and the On/Off indicator is activated.
3. Press either the
up or down button to change the alarm status to off and press Suunto.
The alarm symbol disappears from the display.
Acknowledging alarms
When you hear the alarm, you can acknowledge it by pressing any of the Suunto
X6/X6M buttons. The alarm stops automatically after 30 seconds.
3.2.3. Time
The current time is visible on the second row of the Time mode´s main display.
Dual time allows you to keep track of another time, for example, another time zone
when you are traveling. The dual time is displayed on the third row of the Time mode
main display as a shortcut. To scroll to the dual time shortcut, press Stop/CL in the
main display.
Setting the time and the dual time
To set the time and the dual time:
1. In the Function menu, scroll to Time and press Suunto. The menu with the options
Time and Dual time is displayed.
2. Scroll to either
Time or Dual time and press Suunto. The hour selection is
activated.
3. Change the
hour with the arrow buttons and press Suunto. The minute selection is
activated.
19
NOTE: If the time is displayed as a 12-hour clock, the symbol AM or PM is displayed on
the last row. For more information about the 12/24-hour clock, refer to chapter 3.2.6.
4. Change the
minutes with the arrow buttons and press Suunto. The second selection
is activated.
5. When you press the arrow down button, the seconds are zeroed. If you want to set
specific seconds, press the arrow up button and the seconds start to increase. When
the seconds setting is correct, press Suunto. You automatically return to the Function
menu.
NOTE: When you set the seconds for time, they are automatically updated in the dual
time as well.
NOTE: When you are setting the dual time, you can only set hours and minutes, the
seconds are retrieved from the Time option.
3.2.4. Date
The date has three different formats: dd.mm, mm.dd or day. For more information about
changing the format, refer to chapter 3.2.6.
Changing the date
To change the date:
1. In the Function menu, scroll to Date and press Suunto.
2. Change the value of the first active field (either day or month, depending on the
format) with the arrow buttons and press Suunto. The second field is activated.
3. Change the value of the second field with the arrow buttons and press
Suunto. The
year selection is activated.
4. Change the year with the arrow buttons and press
Suunto. (All the years mean the
21st century.) You automatically return to the Function menu.
20
NOTE: The weekday is updated automatically on the last row according to the set
date.
3.2.5. General
The General function includes the general settings for using your Suunto X6/X6M.
Setting the tones
Tones are the sounds that indicate that you have successfully pressed the buttons.
The tones can be set on or off.
To set the tones:
1. In the Function menu, scroll to General and press Suunto. The General menu is
displayed.
2. Scroll to
Tones and press Suunto. The On/Off field is activated.
3. Change the value of the field to either
on or off with the arrow buttons and press
Suunto. The tones are now set.
Setting the icons
Icons are the symbols that appear for a moment when you change the mode. You can
either show or hide them.
To set the icons:
1. In the Function menu, scroll to General and press Suunto. The General menu is
displayed.
2. Scroll to
Icons and press Suunto. The On/Off field is activated.
3. Change the value of the field to either on or off with the arrow buttons and press
Suunto. The icons are now set.
21
Setting the backlight
Light is the backlight of the Suunto X6/X6M display. Light has three possible settings:
• Normal: The light goes on when you press Start for more than 2 seconds in any
other mode than the Chrono mode. The light is on for 5 seconds after the last press
of any button.
NOTE: If the backlight setting is normal and you press Start in Chrono mode, the
Chrono is activated. If you want to use the light in the Chrono mode, you have to set
the backlight to Night Use.
•
Off: The light does not go on from any button or during an alarm.
•
Night Use: The light goes on when you press any of the buttons and stays on for
5 seconds after the last press of a button.
NOTE: The backlight goes on when an alarm sounds in Normal and Night Use.
To change the light setting:
1. In the Function menu, scroll to
General and press Suunto. The General menu is
displayed.
2. Scroll to
Light and press Suunto. The current light setting is activated.
3. Select the light setting with the arrow buttons and press
Suunto. The light setting is
set and you return to the Function menu.
Calibrating the air pressure sensor
The pressure sensor of the Suunto X6/X6M is accurately calibrated when the product
leaves the factory. However, the calibration can slightly shift over time. You can adjust
the calibration offset but you should only do it if you notice that the current air pressure
shown on the bottom row in the Weather mode differs from a reference value of the
barometric pressure measured with a certificated high-accuracy barometer. You can
22
set the value by 0,1 hPa or 0,01 inHg steps. The reference value should be measured
with at least the same accuracy. If you are uncertain, contact the Suunto technical
service before changing the calibration.
To change the pressure sensor calibration:
1. In the Function menu, scroll to General and press Suunto. The General menu is
displayed.
2. Scroll to
Sensor and press Suunto. The text sensor calibration appears and the
current measured absolute air pressure is displayed as active.
3. With the arrow buttons, set the absolute air pressure value to match the measured
reference value and press Suunto. You return to the Function menu.
NOTE: You can return the original calibration by scrolling the sensor calibration value
until text DEFAULT is displayed in the middle row.
3.2.6. Units
The units menu includes the units that are used with all the Suunto X6/X6M functions
and settings. The unit settings affect the way information is displayed in all the Suunto
X6/X6M modes.
Setting the time format
The time setting defines whether the 12- or 24-hour clock is used.
To change the 12/24-hour display:
1. In the Function menu, scroll to
Units and press Suunto. The Units menu is
displayed.
2. Scroll to
Time and press Suunto. The 12/24 h field is activated.
3. Select the correct setting with the arrow buttons and press
Suunto. The time display
is set.
23
Setting the date format
The Date setting defines the format in which the date is displayed. The possible formats
are:
• DD.MM: Day before the month, e.g. 27.11.
• MM.DD: Month before the day, e.g. 11.27.
•
Day: Only the day is displayed, e.g. 27.
To change the date format:
1. In the Function menu, scroll to
Units and press Suunto. The Units menu is
displayed.
2. Scroll to
Date and press Suunto.
3. Select the correct date format with the arrow buttons and press
Suunto. The format
is set and you return to the Function menu.
Setting the temperature unit
The Temp setting defines the unit in which the temperature is displayed. The options
are Celsius (°C) and Fahrenheit (°F).
To change the temperature unit:
1. In the Function menu, scroll to Units and press Suunto. The Units menu is
displayed.
2. Scroll to
Temp and press Suunto. The temperature unit field is activated.
3. Select the unit with the arrow buttons and press
Suunto. The temperature unit is
set.
Setting the air pressure unit
The Pres setting defines the unit in which the air pressure is displayed. The options
are hPa and inHg.
24
To change the air pressure unit:
1. In the Function menu, scroll to
Units and press Suunto. The Units menu is
displayed.
2. Scroll to
Pres and press Suunto. The air pressure unit field is activated.
3. Select the correct unit with the arrow buttons and press
Suunto. The unit of the air
pressure is set.
Setting the elevation unit
The Elev setting defines the unit in which the elevation is displayed. The options are
meters (m) and feet (ft).
To change the elevation unit:
1. In the Function menu, scroll to Units and press Suunto. The Units menu is
displayed.
2. Scroll to
Elev and press Suunto. The elevation unit field is activated.
3. Select the correct unit with the arrow buttons and press
Suunto. The unit of the
elevation is set.
Setting the ascent/descent rate unit
The Asc/Dsc setting defines the way the ascent or descent rate is displayed. The
possible formats are:
• m/s
• m/min
• m/h
• ft/s
• ft/min
• ft/h
25
To change the Asc/Dsc format:
1. In the Function menu, scroll to Units and press Suunto. The Units menu is
displayed.
2. Scroll to
Asc/Dsc and press Suunto.
3. Select the correct format with the arrow buttons and press
Suunto. The format is set
and you return to the Units menu.
3.3. COMPASS MODE
3.3.1. Main Display
When you select the Compass mode, the main display opens. The main display has
three rows.
Bearing
First row displays the bearing pointed with the sighting marks of Suunto X6/X6M. The
bearing is displayed in bold when the compass is level.
Compass
The second row displays the heading of the Suunto X6/X6M as a graphical presentation
of a compass rose. The rose displays the cardinal and half-cardinal points.
The magnetic sensor of the compass functions for 40 seconds at a time. After this
period the compass moves into power-saving mode and the message “start compass”
is displayed. Press Start, to activate the compass again.
26
Shortcuts
The third row contains shortcuts to three functions. To change the function, press
Stop/CL.
• Altitude: In Alti use, it displays the current altitude, and in Baro use, it displays the
reference altitude. For more information about the Alti and Baro uses, see section
3.3.2.
•
Bearing tracking: Bearing tracking helps you to follow a certain bearing in terrain.
When you scroll to bearing tracking for the first time, it is 0°. To activate the search for
bearing, move your Suunto X6/X6M horizontally until the chosen bearing is displayed
on the first row and press Start. The selected bearing is displayed on the third row
until you select a new bearing with the Start button. When you have selected the
bearing tracking, the compass rose in the middle row displays a dotted vertical line
indicating the bearing tracking set.
NOTE: The tracking always remembers the last direction selected, when you next
scroll to it.
•
Time: Displays the current time.
NOTE: The shortcuts will also function normally in the power-saving mode. When you
select the bearing shortcut, the compass will automatically be activated.
3.3.2. Use
With the Use function you can define whether the air pressure measurement is used
to measure the altitude or to represent the weather conditions.
If you select Alti (altimeter), the measured air pressure is displayed as altitude and all
changes of atmospheric pressure are interpreted as changes in altitude.
27
When the Alti use is selected, the altitude reading of Compass, Hiking and Hiking
Chrono modes changes, but the atmospheric pressure (sea level) in the second row
of the Weather mode remains constant. The absolute pressure changes if it is selected
as a shortcut on the third row of the Weather mode.
If you select Baro (barometer), the measured air pressure is displayed as weather
information and all changes in atmospheric pressure are interpreted as being due to
a change in the weather.
When the Baro is selected, the altitude reading in the Compass, Hiking and Hiking
Chrono modes remains constant. The atmospheric pressure (sea level and absolute)
in the Weather mode changes.
Select the correct use according to what you want to measure. For example, on a hiking
trip, you can select Alti for the day to see how high you have climbed. When you camp
for the night, you can change the use to Baro to make sure that the weather changes
do not catch you by surprise.
To select either Altimeter or Barometer use:
1. In the Function menu, scroll to Use with the arrow buttons and press Suunto. The
Alti/Baro field is activated.
2. Change the content of the field with the arrow buttons and press
Suunto. You then
return to the Function menu.
3.3.3. Altitude/Sealevel
In order for the altimeter to function correctly you need to set the reference altitude.
This means that you set an altitude reading that is equal to the real altitude. Set the
reference altitude in a place where you know the altitude, for example, with the help
of a topographical map. The Suunto X6/X6M has a factory set reference altitude that
28
corresponds to the standard barometric pressure (1013hPa/29.90inHg) at sea level. If
you do not know your current altitude or the correct sea level pressure, you can have an
estimate of your altitude by setting the sea level pressure to 1013 hPa/29.90 inHg.
In the Weather mode, Altitude is replaced with Sealevel, this functions and is set in the
same way as Altitude.
To set the reference altitude:
1. In the Function menu, scroll to Altitude with the arrow buttons and press Suunto.
2. With the arrow buttons, set the reference altitude in the field to match the altitude of
you current location and press Suunto. You return to the Function menu.
If you do not know your altitude, you can use the air pressure to help determine the
altitude. To do this, select the Weather mode and set the current sea level air pressure.
You can find out the sea level air pressure, for example, from the airport, weather station
or Internet weather pages.
3.3.4. Compass
The compass menu includes functions for either calibrating the compass or setting
its declination.
Calibrating the compass
You should calibrate the compass if it does not seem to work well, for example, when
it displays the wrong compass heading or the heading changes too slowly. You should
also calibrate the compass after replacing the battery.
Strong electromagnetic fields, such as electric lines, loudspeakers and magnets, can
affect the compass calibration. Therefore calibrate the compass if your Suunto X6/X6M
has been exposed to these fields.
29
You should also calibrate the compass before a long trip.
NOTE: Calibrate the compass before using it for the first time.
NOTE: Remember to hold the Suunto X6/X6M level during the calibration.
To calibrate the compass:
1. In the Function menu, scroll to
Compass with the arrow buttons and press Suunto.
2. In the compass menu, move to
Calib with the arrow buttons and press Suunto.
3. The screen displays the text “
rotate 360°” and a countdown from 5 to 0. When the
countdown reaches 0, the calibration starts. Hold the Suunto X6/X6M level and slowly
rotate the device in a full clockwise or counterclockwise circle.
• The level symbol indicates the ongoing calibration. The animation represents the
progress of the calibration.
• If the calibration succeeds, the message “
complete” is displayed and the Suunto
X6/X6M returns to the Function menu.
• If the calibration fails, the message “
try again” is displayed and the process starts
again from the countdown.
• If the calibration fails five times, the message “
failed, refer manual” is displayed
and the Suunto X6/X6M returns to the compass menu.
If the calibration fails five times in a row, it may be possible that you are in an area that
has sources of magnetism, such as large metal object, power lines, loudspeakers and
electric motors. Move to another location and try to calibrate the compass again.
You can also remove the battery and then insert it again. Also make sure, that the
compass remains level during the calibration—calibration may fail if the level is un-
stable.
If the calibration continues to fail, contact the authorized Suunto service.
30
Setting the compass declination
You can compensate for the difference between true north and magnetic north by
adjusting the compass declination. The declination can be found, for example, from
the topographic maps of your local area.
To set the compass declination:
1. In the Function menu, scroll to Compass with the arrow buttons and press Suunto.
2. In the compass menu, move to
Declin with the arrow buttons and press Suunto.
The first row of the next window is activated.
3. Select the correct option (Off/East/West) with the arrow buttons and press
Suunto.
The degrees field is activated.
4. Set the degree with the arrow buttons. The initial value is either 0.0° or the value
accepted when last setting the declination.
5. Press
Suunto. You return to the compass menu.
3.4. WEATHER MODE
3.4.1. Main Display
When you select the Weather mode, the main display opens. The main display has
three rows.
Temperature
The first row displays the temperature in the selected unit. For more information about
defining the temperature unit, refer to chapter 3.2.6.
NOTE: Because the sensor is close to your wrist, you have to keep the Suunto X6/X6M
away from the body’s temperature at least for 15 minutes to measure the correct air
temperature.
31
Air pressure
The second row displays the air pressure at sea level. For more information about
defining the air pressure unit, refer to chapter 3.2.6.
Shortcuts
The third row contains shortcuts to three functions. To change the function, press
Stop/CL.
• Trend: A graphical presentation of the air pressure development (sea level) during
the last 6 hours in 15-minute intervals. One step on the vertical axis represents one
hPa and one step on the horizontal axis represents 15 minutes.
•
Absolute air pressure: The absolute air pressure is the actual pressure in the current
location.
•
Time: Displays the current time.
3.4.2. Use
With the Use function you can define whether the air pressure measurement is used
to define the altitude or to represent the weather conditions. For more information,
refer to chapter 3.3.2.
NOTE: For most Weather mode functions the correct Use setting is Baro.
3.4.3. Sealevel
With this function you can set the sea level barometric pressure. This is the barometric
pressure at your current location reduced to sea level. For more information about sea
level pressure, refer to chapter 3.3.3.
To set the sea level pressure:
1. In the Function menu, scroll to Sealevel with the arrow buttons and press Suunto.
32
2. With the arrow buttons, set the sea level pressure in the field to match the current
sea level barometric pressure of you current location and press Suunto. You return
to the Function menu.
3.4.4. Alarm
When active, the weather alarm informs you if the air pressure drops more than 4
hPa/0,118 inHg in 3 hours.
NOTE: The weather alarm activates only when the Use function is set to Baro.
To activate or deactivate the weather alarm:
1. In the Function menu, scroll to
Alarm with the Arrow buttons. The current status of
the alarm can be seen from the Function menu.
2. Press
Suunto. The On/Off field is activated.
3. Change the field to either on or off with the arrow buttons and press
Suunto.
When the weather alarm goes on, the alarm symbol flashes and the backlight goes
on. To acknowledge the weather alarm, press any button.
3.4.5. Memory
The memory stores weather-related information from the last 48 hours. When you scroll
through the stored information, it is presented in the following order:
• Maximum sea level air pressure during the period measured, date and time.
• Minimum sea level air pressure during the period measured, date and time.
• Maximum temperature during the period measured, date and time.
• Minimum temperature during the period measured, date and time.
• Sea level air pressure and temperature in relation to the time and date starting from
the current moment. The first 6 hours are displayed in 1-hour intervals, the next 42
hours in 3-hour intervals.
33
NOTE: If the Use function has been set to Alti (altimeter), the barometric value stored
in memory is always the same.
To view the weather information stored in the memory:
1. In the Function menu, scroll to
Memory with the arrow buttons and press Suunto.
The first information page is displayed.
2. Scroll the information with the arrow buttons—the
up arrow scrolls forward and the
down arrow backward.
3. To stop
viewing the memory content, press either Suunto or Stop/CL at any time.
3.5. HIKING MODE
3.5.1. Main Display
When you select the Hiking mode, the main display opens. The main display has
three rows.
Ascent/descent rate
First row displays the ascent/descent rate in the selected unit. For more information
about defining the ascent/descent rate unit, refer to chapter 3.2.6.
Altitude
The second row displays the altitude. For more information about defining the altitude
unit, refer to chapter 3.2.6.
Shortcuts
The third row contains shortcuts to three functions. To change the function, press
Stop/CL.
34
• Asc: The cumulative ascent since the logbook was started. If the logbook is not
running, the display shows text “asc 0”.
•
Differ: When you select the Differ function, it displays the difference in altitude and
time since the last reset of the function. To reset and start a new measurement, press
Start. Differ is always in the measuring mode, i.e. it measures the time and altitude
difference constantly but displays them only when you select the function.
During the first 10 hours both hours and minutes are displayed. After that, during the
next 89 hours, only hours are displayed and, finally, the display shows only a dash
and letter ‘h’.
•
Time: Displays the current time.
3.5.2. Logbook
The logbook allows you to save information regarding, for example, a hiking trip. When
you start the logbook, it starts gathering information about the cumulative ascents and
descents, average ascent and descent rates, highest and lowest points and specific
marks you can set during the trip. When you stop the logbook, the information gathered
thus far is recorded as a logbook file that can be viewed later. The maximum duration
of one logbook is 168 hours (one week). After this the logbook stops automatically. The
Suunto X6/X6M can store 20 logbook files at one time. More logbooks can be saved on
your PC with the help of the PC Interface. For more information, refer to chapter 4.1.
NOTE: To record a complete graph of the activity, use the stopwatch in the Chrono
mode.
Starting the logbook
To start the logbook:
1. Press Suunto in the main display.
35
2. In the Function menu, scroll to Logbook with the arrow buttons and press Suunto.
3. Scroll to
Start and press Suunto.
If the logbook is not running and there is enough memory left, recording begins. The
message “logbook started” is displayed and you return to the Function menu.
If the logbook is already activated, the message “logbook already running” is displayed
and you return to the Function menu, where the Stop field is displayed in reversed
color.
If there is not enough memory left, the message “memory full” is displayed and the
Suunto X6/X6M moves to a display that asks you to erase a logbook file.
Select the logbook file to be deleted with the arrow buttons and press Suunto. The file
is deleted from the memory and you return to the logbook menu.
Stopping the logbook
To stop the logbook:
1. In the Function menu, scroll to Logbook with the arrow buttons and press Suunto.
2. Scroll to Stop and press
Suunto. The recording stops and the message “logbook
stopped” is displayed. You automatically return to the Function menu.
If the logbook was not running when you tried to stop it, you return to the Function
menu.
Viewing logbook les
The logbook list includes the logs recorded in the Suunto X6/X6M memory. With the
list function you can either view the logs or erase them from the memory. You can
scroll the list forward from the first item and either forward or backward from all the
other items.
36
To view the log files:
1. In the Function menu, scroll to Logbook with the arrow buttons and press Suunto.
2. Scroll to
View and press Suunto. A list of all the saved logbook files is displayed.
3. Scroll the list with the arrow buttons until the logbook file you want to view is active
and press Suunto. The first display of the logbook file is shown.
4. Press the
up arrow to move to the next display. The displays are shown in the following
content:
• Starting date and time, total time of the file and the number of runs. An ascent and
consecutive descent of at least 50 meters is considered a run.
• Total ascent and the average ascent rate
• Total descent and the average descent rate
• The highest point, date and time
• The lowest point, date and time
• The marks the user has added to the logbook file include the altitude, date and
time of the mark. The maximum number of marks is 10.
Total ascent and total descent are updated in 10 s intervals. To return to the main
display, press Suunto for more than 2 seconds.
NOTE: If you try to view the list but there are no recorded logbook files, the message
“no logbook files” is displayed and you return to the logbook menu.
Erasing logbook les
To erase the log files:
1. In the Function menu, scroll to Logbook with the arrow buttons and press Suunto.
2. Scroll to
Erase and press Suunto. A list of all the recorded logbook files is
displayed.
37
3. Scroll the list with the arrow buttons until the logbook file you want to erase is active
and press Suunto. The Suunto X6/X6M displays the file and the text “erase?”.
4. If you want to accept the deletion, press
Suunto. You return to the list of logbook
files.
5. If you want to cancel the deletion, press
Stop/CL. You return to the previous menu.
Viewing logbook history
The logbook history contains the cumulative values of ascents and descents and the
highest point of all logbooks (Hiking and Chrono Modes) recorded during the Suunto
X6/X6M lifetime.
To view the history:
1. In the Function menu, press Suunto to enter Logbook.
2. Scroll to
History and press Suunto.
3. Press the
up arrow to scroll the history information. The information is displayed in
the following order:
• Cumulative ascent.
• Cumulative descent.
• Highest point, date and time.
Resetting the logbook history
To reset the logbook history:
1. Connect your Suunto X6/X6M to Suunto Activity Manager.
2. Click Wristop
History Reset History. This will transfer the current history
data to SAM database and set the history values in the Wristop computer memory
to zero.
38
Logbook marks
You can add marks to the logbook file and record the information about the altitude of
a specific point and time. This can only be done in Hiking mode. The maximum number
of marks in each file is 10.
To add a mark, short press Start when the logbook is running. A long press activates
the backlight and no logbook mark is made. The marks are added in the logbook file
and they can be viewed through the file list (refer to chapter 3.5.2.). When you have
added the marks, the message “mark point saved” is displayed.
When you have saved the marks, the PC can create a profile that connects them with
a line. With this feature you can, for example, create a simplified altitude profile of your
trip. You can also use marks to compare the difference in time and altitude between two
points of the trip. (Compare with the Differ function on chapter 3.5.1.)
3.5.3. Use
With the Use function you can define whether the air pressure measurement is used
to set the altitude or to represent the weather conditions. For more information, refer
to chapter 3.3.2.
3.5.4. Altitude
With this function you can set the reference altitude. For more information about the
reference altitude, refer to chapter 3.3.3.
3.5.5. Alarms
The altitude alarm is intended to warn you if you pass the preset altitude limit. The
ascent/descent alarm, in its turn, warns you if your ascent/descent rate is faster than the
preset rate. When the alarm sounds, you can acknowledge it by pressing any button.
39
NOTE: The alarms are functional only when the Use function is set to Alti.
Setting altitude alarm
To set the altitude alarm:
1. In the Function menu, scroll to Alarms with the arrow buttons and press Suunto. The
alarm menu is displayed.
2. Scroll to
Altitude and press Suunto. The On/Off field is activated.
3. Change the status of the alarm to either on or off with the arrow buttons and press
Suunto. The altitude field is activated.
4. Change the altitude with the arrow buttons and press Suunto. You return to the
Function menu.
Setting the ascent/descent alarm
To set the ascent/descent alarm:
1. In the Function menu, scroll to Alarms with the arrow buttons and press Suunto. The
alarm menu is displayed.
2. Scroll to
Asc/Dsc and press Suunto. The On/Off field of the next display is
activated.
3. Change the status of the alarm to either on or off with the arrow buttons and press
Suunto. The rate field is activated.
4. Change the asc/dsc rate with the arrow buttons and press
Suunto. You return to the
main display.
NOTE: The ascent is indicated by positive values, the descent by negative values.
40
3.6. HIKING CHRONO
3.6.1. Main Display
When you select the Hiking Chrono mode, the main display opens. The main display
has three rows.
Altitude
The first row displays the altitude in the selected unit. For more information about
defining the altitude unit, refer to chapter 3.2.6.
Stopwatch
The second row displays the total time or the split time. The
split time is the time from
the start of the timing to this moment. When you navigate to the main display, the time
on the second row is either 0.00,0, the time of the previous timing, or, if the stopwatch
has already started, a running time. The time starts running when you press Start.
If you want to view a split and lap time (on the third row), press Start again. The time
on the middle row stops for 3 seconds to display the split time and then starts running
again.
When you want to stop the timing, press Stop/CL while in the Chrono mode. The stop
time is then displayed on the second row. You can zero the display by long pressing
Stop/CL.
NOTE: If you want to continue the same timing after viewing the lap and split times,
press Start instead of zeroing the display.
NOTE: You must have free space in the memory to be able to start the timing. If the
memory is full, the message “memory full” is displayed and the Suunto X6/X6M suggests
the oldest memory file to be erased. Erase the suggested file by pressing Suunto or
select and erase another file. After the deletion, you can start the chrono. For more
41
information about erasing memory files, refer to chapter 3.6.2.
Lap time
The
lap time means the time from the last press of Start, i.e. from the last intermediate
time to the current time. The lap time runs on the third row.
When you press Start, the lap time stops for 3 seconds to display the lap time and starts
running from zero again (for the next lap).
When you stop the timing by pressing Stop/CL, the last lap time is displayed on the
third row.
3.6.2. Memory
The memory records data continuously when the chrono is active, that is, when the
timing is running.
Viewing memory les
The memory file can be viewed in relation to the time and altitude data.
To view a memory file:
1. In the Function menu, scroll to
Memory with the arrow buttons and press Suunto.
The memory menu is displayed.
2. Scroll to
View alti and press Suunto. The list of memory files is displayed. In the file
list the files are organized so that the latest file is the first.
3. Scroll to the file you want to view with the arrow buttons and press
Suunto. The first
information screen is displayed.
4. Scroll the information with the arrow buttons. The information is displayed in the
following order:
• Total ascent and the average ascent rate.
42
• Total descent and the average descent rate.
• Highest point, time and date.
• Lowest point, time and date.
• Total duration of the file and the amount of laps in the file.
• More specific information about that file including altitude and ascent and
descent rates on individual points according to recording interval, and graphical
presentations about the altitude. These are displayed in the following way:
First row:
• Total elapsed time
Second row:
• The left side displays a graphical presentation about the altitude in relation to
time. The scale of the graphical presentation depends on the set recording
interval and the recorded altitude differences.
• The right side displays ascent and descent rates in the point of time displayed
in the first row. For saved lap times, the right side displays lap and split
numbers.
Third row:
• Altitude displayed with the set recording interval (10 or 60 seconds).
NOTE: If you try to view a file when the file list is empty, the message “no files in memory”
is displayed and you return to the Function menu.
NOTE: When you start the Chrono, it starts recording the altitude profile. If the memory
becomes full while the recording is on, Suunto X6/X6M stops recording the profile.
However, the stopwatch remains running and the summary values are updated.
43
Erasing memory les
If the memory is full, you cannot start the timing until you have erased at least one
memory file.
To erase a memory file:
1. In the Function menu, scroll to Memory with the arrow buttons and press Suunto.
The memory menu is displayed.
2. Scroll to
Erase and press Suunto. The list of memory files is displayed. In the file list
the files are organized so that the latest file is the first.
3. Scroll to the file you want to erase with the arrow buttons and press
Suunto.
4. Accept the erase by pressing
Suunto in the field, that displays the text “erase?” and
the time and date of the file. If you want to cancel the deletion, press Stop/CL. In
both cases you return to the file list.
NOTE: If you try to erase a file when the file list is empty, the message “no files in
memory” is displayed and you return to the Function menu.
Setting the recording interval
The recording interval defines how often the information is saved to the memory
when the timing is running. The recording interval can be either 10 or 60 seconds.
If you change the interval while the stopwatch is running, the change does not affect
the current recording. The change applies to the next stopwatch recording.
To set the interval:
1. In the Function menu, scroll to
Memory with the arrow buttons and press Suunto.
The memory menu is displayed.
2. Scroll to
Interval and press Suunto.
3. Select the interval with the arrow buttons and press
Suunto.
44
The memory capacity is 33 h with 10 s recording interval and 200 h with 60 s interval.
Free memory capacity in % is displayed in the Interval menu below the intervals with
the text “free…%”.
3.6.3. Altitude
With this function you can set the reference altitude. For more information about the
reference altitude, refer to chapter 3.3.3.
3.6.4. Use Alti/Baro
With the Use function you can define whether the air pressure measurement is used
to represent the altitude or the weather conditions. For more information, refer to
chapter 3.3.2.
3.6.5. Reminder
You can activate a reminder to sound a signal after set periods. This feature is helpful,
for example, when you are hiking and want to remember to drink at regular intervals.
It can also be used for interval training.
NOTE: You do not have to acknowledge the reminder in any way when you hear it.
Starting the reminder
To activate the reminder:
1. In the Function menu, scroll to Reminder with the arrow buttons and press Suunto.
The Reminder menu is displayed.
2. Scroll to
Start and press Suunto. If the interval is set, the message “reminder started”
is displayed and you return to the Function menu.
45
Stopping the reminder
To stop the reminder:
1. In the Function menu, scroll to Reminder with the arrow buttons and press Suunto.
The Reminder menu is displayed, and if the reminder is active, the Stop field is
displayed in reversed color.
2. Scroll to
Stop and press Suunto. The message “reminder stopped” is displayed and
you return to the Function menu.
NOTE: If the reminder is not active and you try to stop it, you return to the Function
menu without any message.
Reminder interval
When you navigate to the Reminder menu for the first time, the interval is 1.00. After
this, the interval displayed in the Reminder menu is the interval that was set the last
time the reminder was used.
To change the interval:
1. In the Function menu, scroll to Reminder with the arrow buttons and press Suunto.
The Reminder menu is displayed.
2. Scroll to
Int and press Suunto. The minutes field is activated.
3. Set the minutes with the arrow buttons and press
Suunto. The seconds field is
activated.
4. Set the seconds with the arrow buttons and press
Suunto. You return to the Reminder
menu and the Start field is activated.
NOTE: The reminder interval can not be shorter than 5 seconds.
46
3.6.6. Effect of air temperature on altitude measurement
The atmospheric pressure means the weight of air mass above the observer: at a
higher altitude there is less air than at a lower altitude. The principle of an altimeter is
to measure the different air pressure between different altitudes.
47
Table 1. Normal temperatures corresponding to different altitudes
Altitude (m) Altitude (ft) Temperature (ºC) Temperature (ºF)
above sea level above sea level
0 0 15.0 59.0
200 656 13.7 56.7
400 1312 12.4 54.3
600 1969 11.1 52.0
800 2625 9.8 49.6
1000 3281 8.5 47.3
1200 3937 7.2 45.0
1400 4593 5.9 42.6
1600 5250 4.6 40.3
1800 5906 3.3 37.9
2000 6562 2.0 35.6
2400 7874 -0.6 30.9
2800 9187 -3.2 26.2
3000 9843 -4.5 23.9
3400 11155 -7.1 19.2
3800 12468 -9.7 14.5
4000 13124 -11.0 12.2
4500 14765 -14.3 6.4
5000 16405 -17.5 0.5
5500 18046 -20.8 -5.4
6000 19686 -24.0 -11.2
48
The outside temperature affects the air weight. Consequently the air pressure difference
between two altitudes is also dependant on temperature.
The altitude calculation of Suunto X6/X6M is based on the air pressure at certain
normal temperatures. Each altitude has a definitive normal temperature. The normal
temperatures at each altitude are presented in Table 1.
The altitude measurement error caused by an abnormal temperature gradient can be
approximated as follows. If the sum of the temperature offsets from the normal
temperatures determined at two different altitudes is 1 ºC, the altitude difference
calculated by the Suunto X6/X6M is 0.2% off the real altitude difference (When using
imperial units the offset factor is 0.11% / 1 ºF). This is because the real temperatures
are not always the same as the normal temperatures. A higher than normal temperature
causes the calculated altitude difference to be smaller than the real altitude difference
(your mountain ascent was actually higher). Consequently, a lower than normal
temperature causes the calculated altitude difference to be larger than the real altitude
difference (you did not ascend quite as high as displayed).
Table 2 shows an example in which the temperature offsets are positive. In this example,
the reference altitude is set at 1000 m. At 3000 m the altitude difference is 2000 m and
the Suunto X6/X6M shows 80 m too little (20 ºC * 2000 m * 0.002/ºC = 80 m). Your
actual altitude is thus 3080 m.
All Suunto products with an altimeter are temperature-calibrated. This means that at
constant pressure, the pressure sensor reading is always the same independent of
the unit’s own temperature. However, the air temperature can still affect the altitude
readings as described above.
49
Table 2. Example using meters and Celsius
Lower point Higher point
Set reference altitude (real altitude) 1000 m
Displayed altitude 3000 m
Real outside temperature +17.5 ºC +6.5 ºC
Normal (table) temperature +8.5 ºC -4.5 ºC
Temperature offset (= real - normal) +9 ºC +11 ºC
Sum of temperature offsets +9 ºC + +11 ºC = 20 ºC
Table 3 shows an example in which the temperature offsets are negative. This time
imperial units are used. The reference altitude is set at 3280 feet. At 9840 feet the
altitude difference is 6560 feet and the Suunto X6/X6M shows 100 feet too much (-14
ºF * 6560 ft * 0.0011/ºF = -100 ft). Your actual altitude is thus 9740 ft.
Table 3. Example using feet and Fahrenheit.
Lower point Higher point
Set reference altitude (real altitude) 3280 ft
Displayed altitude 9840 ft
Real outside temperature +36.3 ºF +18.9 ºF
Normal (table) temperature +47.3 ºF +23.9 ºF
Temperature difference (= real - normal) -9 ºF -5 ºF
Sum of temperature offsets -9 ºF + -5 ºF = -14 ºF
50
➦
4. ADDITIONAL FEATURES
4.1. PC INTERFACE
With the PC Interface you can transfer and store
the logs you have gathered with your Suunto
X6/X6M to your PC. The logs can be either hiking
logs stored in the Suunto X6/X6M logbook files,
weather logs stored in the weather memory or
chrono logs stored in the chrono memory. When
the data has been transferred, you can organize,
view and add related information to it easily with
the Suunto Activity Manager software.
The PC Interface cable and Suunto Activity
Manager are delivered in the same package with
your Suunto X6/X6M. The installation instructions
for the software can be found on the cover of the
Suunto Activity Manager CD-ROM.
4.1.1. Transferring data
Make sure your computer has a free serial port and
is not used by other processes. Start transferring
the data by attaching the cable to the computer
serial port and plugging the other end to your
Suunto X6/X6M. You can also use USB port with
serial/USB adapter.
The wristop goes automatically to the data transfer
mode.
51
When the cable is connected, open the Suunto Activity Manager (SAM). Click on the
“Wristop” icon in the upper left corner of the SAM to open the data transfer window.
Press the “Connect” button in the lower part of the window to transfer the list of the log
files from the wristop computer to the SAM window. When you drag and drop the logs
into appropriate folders, they are saved to the hard disk of your PC. The folders are
located on the left side of the SAM data transfer window. If the Suunto Activity Manager
is already open before you have connected the cable, click on the “Connect” button to
display the log list. When you have uploaded the logs, you can delete them from the
Suunto X6/X6M memory by dragging them to the Recycle bin in the lower left corner
of the Suunto Activity Manager to create more space for new logs.
For further information, see the Suunto Activity Manager Help. To access the help, click
the help icon on the upper right corner of the display. You can also refer to the Suunto
Activity Manager Tutorial for step-by-step instructions. To access the tutorial, click on
the Tutorial link in the Help Contents window in the SAM Help.
4.1.2. Suunto Activity Manager Features
Users
You can create a user profile and add information about yourself and your Suunto
X6/X6M. Creating user information is useful if you have several wristop computers
you want to use with the same computer, or when many people use the same wristop
computer—with the user information you can always find the correct data, such as
logs.
Logs
When you have uploaded the logs from the Suunto X6/X6M, you can organize them
with the Suunto Activity Manager. You can, for example, create folders where you can
52
store the logs—the hiking logs can be arranged in a different folder than the skiing logs.
You can also sort the logs, move them between folders and delete them or search the
log information. It is even possible to upload them to the SuuntoSports.com site.
Charts and Data
You can examine the log information by creating charts from it. The charts show the
development of altitude or temperature. Open the folders and select the logs you want
to see. Click on the “Open Logs” button to view the file as a chart. If you have opened
several logs, they are listed in the window below the chart. There you can select which
profiles you want to view simultaneously. You can also add bookmarks to a chart. The
bookmark can either be a text or an image —for example a photograph of the highest
peak of your trek.
You can also view the log information as a data list where the altitude, and temperature
values are listed in chronological order. To view a data list, click on the “Data” button on
the upper part of the chart window. Both charts and the list can be printed.
Analyzing Data
You can analyze the data in the logs according to your activities and possible time
periods. Select the files you want from the folder and click on “Open Logs”. Then press
“Analyze”. The analysis can display information about altitude zones and durations. The
analysis results are displayed as 3-D bar diagrams that you can rotate on the screen.
53
Changing Suunto X6/X6M Settings
You can change some Suunto X6/X6M settings with the Wristop Computer section of
the Suunto Activity Manager. You can change the following settings:
• Asc/Dsc—select the used ascent/descent unit (m/s, m/min, m/h, ft/s, ft/min, ft/h).
• Altitude—change the used altitude unit (m or ft).
• Pressure —select the used pressure unit (hPa or inHg).
• Temperature—select the used temperature unit (°F or °C).
• Time—select between 12- or 24-hour display.
• Date—select the date format (day/month, month/day, day).
• Light—select the light setting (Normal, NightUse, Off).
• Tones—set the button tones on or off.
• Icons—set the icons on or off.
For more detailed information and step-by-step instructions for the above features,
refer to the Suunto Activity Manager Help or Tutorial.
4.2. SUUNTOSPORTS.COM
SuuntoSports.com is an international free web community where you can refine and
share the data that you have measured with your personal Suunto instrument and
analyzed with the sport-specific PC interface. SuuntoSports.com offers you a number
of features that help you get the most out of your sport and your Suunto X6/X6M.
If you already own a personal Suunto sports instrument you can access all sport-
specific functions through registration. If you do not yet have an instrument you
may either log on as a guest or register yourself. As a guest you can view and read,
but registration gives you the right to use other functions and participate in
discussions.
54
4.2.1. System Requirements
SuuntoSports.com has the following system requirements:
• Internet Connection
• Modem: recommended 56k or faster
• Browser: IE 4.0 or better, Netscape 4.7x or newer
• Resolution: minimum 800 x 600, best viewed with 1024 x 768
4.2.2. SuuntoSports.com Sections
SuuntoSports.com includes three sections all of which have several functions. The
following paragraphs describe only the basic functions of SuuntoSports.com. You
can find detailed descriptions of all the site functions and activities and step-by-step
instructions for using them in the site Help. The Help is available on each page and its
icon is located on the right side of the bar that divides the screen. The Help is frequently
updated as the site develops.
SuuntoSports.com offers several possibilities for searching the information on site. In
addition to the free search, you can search, for example, for groups, users, resorts,
logs and sports.
The information published on the SuuntoSports.com contains internal links so that
you do not always have to search for the information from the very beginning. For
example, if you view a description of a resort, you can follow the links and view the
resort information sender’s personal information, logs related to the resort and charts
created from the logs if the sender has made this information public.
55
My Suunto
This section is meant for your personal information. You can store information about
yourself, your wristop computer, your sporting and training activities, etc. When you
upload your personal logs to SuuntoSports.com with the Suunto Activity Manager, they
are displayed in your personal information. Here you can also manage them and decide
whether they can be presented to all community users or just to limited groups.
When you have uploaded logs to SuuntoSports.com, you can create charts from the
altitude data in the logs and attach them to your training locations and activities. You can
also publish your logs and compare them with other users’ logs. You can also publish
travel reports, which can include text, images and log files.
The My Suunto section also contains a personal calendar that you can use to mark
personal events or practice information. The training diary can be filled with facts about
your training and development, training locations and other useful information.
Communities
In the Communities section, SuuntoSports.com users can form or search groups and
manage their own groups. For example, you can create a group for all your hiker
friends, and share information about each other’s results, give advice and discuss,
where and when you could go for a hiking trip together. Groups can be either open or
closed—closed groups mean that you have to apply for a membership and be accepted,
before you can participate in group activities.
All groups have a home page that displays information about group events and includes
news, noticeboard and other information. Group members can also use group-specific
bulletin boards, chat rooms and group calendars, and add links and create group
activities.
56
Sport Forums
SuuntoSports.com has its own Sports Forum with pages for each Suunto sport. The
basic features and functions are the same for all sports pages—sport-specific news,
bulletin boards and chat rooms. Users can also suggest links to sports-related sites
and tips regarding the sport and equipment to be published on the site, or publish their
own travel reports.
Sport forums include presentations of sports-related locations. Users can rank the
locations an comment on them, and the results are published next to the resort
information. You can also create ranking lists for other things—for example, what group
has most members, who has uploaded most logs or has collected the biggest verticals,
visited the highest places, and so on.
4.2.3. Getting Started
To join the SuuntoSports.com community, connect to the Internet, open your web
browser and go to www.suuntosports.com. When the opening page appears, click the
Register icon and register yourself and your Suunto sports instrument. You can change
and update your personal and equipment profiles in My Suunto section afterwards.
After the registration you will automatically enter the SuuntoSports.com home page
that introduces the site structure and functional principles.
NOTE: SuuntoSports.com is continuously developed further and its content is subject
to change.
57
5. TECHNICAL DATA
General
• Operating temperature -15 °C to +50 °C/+5°F to +120°F.
• Storage temperature -30 °C to +60 °C/-22°F to +140°F.
• Weight 54 g
• Water-resistant 100 m/330 ft (according to ISO 2281)
• Mineral crystal glass
• User-replaceable battery CR2032
• PC interface with serial connector
• Extension strap (accessory)
Altimeter
• Display range –500 m to 9000 m / -1600 ft to 29500 ft
• Resolution 1 m / 3 ft
Barometer
• Display range 300 to 1100 hPa / 8.90 to 32.40 inHg
• Resolution 1 hPa / 0.05 inHg
Thermometer
• Display range -20°C to 60°C / -5°F to 140°F
• Resolution 1°C / 1°F
Compass
• Resolution 1°
58
6. COPYRIGHT AND TRADEMARK NOTICE
This publication and its contents are proprietary to Suunto Oy and are intended solely
for the use of its clients to obtain knowledge and key information regarding the operation
of Suunto X6/X6M products.
Its contents shall not be used or distributed for any other purpose and/or otherwise
communicated, disclosed or reproduced without the prior written consent of
Suunto Oy.
Suunto, Suunto X6/X6Ms and their logos are all registered or unregistered trademarks
of Suunto Oy. All rights are reserved.
While we have taken great care to ensure that information contained in this
documentation is both comprehensive and accurate, no warranty of accuracy is
expressed or implied. Its content is subject to change at any time without notice.
The newest version of this documentation can always be downloaded in www.
suunto.com.
7. CE
The CE mark is used to mark conformity with the European Union EMC directive
89/336/EEC.
59
8. LIMITS OF LIABILITY AND ISO 9001 COMPLIANCE
If this product should fail due to defects in materials or workmanship, Suunto Oy will,
at its sole option, repair or replace it with new or rebuilt parts, free of charge, for two
(2) years from the date of its purchase. This warranty is extended only to the original
purchaser and only covers failures due to defects in materials and workmanship that
occur during normal use while in the period of the warranty.
It does not cover battery replacement, damage or failures resulting in accident, misuse,
neglect, mishandling, alteration or modifications of the product, or any failure caused
by operation of the product outside the scope of its published specifications, or any
causes not covered by this warranty.
There are no express warranties except as listed above. The client can exercise the right
to repair under the warranty by contacting Suunto Oy’s Customer Service department
to obtain a repair authorization.
Suunto Oy and its subsidiaries shall in no event be liable for any incidental or
consequential damages arising from the use of or inability to use the product. Suunto
Oy and its subsidiaries do not assume any responsibility for losses or claims by third
parties that may arise through the use of this device.
Suunto’s Quality Assurance System is certified by Det Norske Veritas to be ISO 9001
compliant in all SUUNTO Oy’s operations (Quality Certificate No. 96-HEL-AQ-220).
9. DISPOSAL OF THE DEVICE
Please dispose of the device in an appropriate way, treating it as
electronic waste. Do not throw it in the garbage. If you wish, you may
return the device to your nearest Suunto representative.
COPYRIGHT
This publication and its contents are proprietary to Suunto Oy.
Suunto, Wristop Computer, Suunto X6, Suunto X6M and their logos are registered
or unregistered trademarks of Suunto Oy. All rights reserved.
While we have taken great care to ensure that information contained in this
documentation is both comprehensive and accurate, no warranty of accuracy is
expressed or implied. Its content is subject to change at any time without notice.
CUSTOMER SERVICE CONTACTS
Global Help Desk +358 2 284 11 60
Suunto USA Phone +1 (800) 543-9124
Canada Phone +1 (800) 776-7770
Suunto website
www.suunto.com
Suunto Oy 2/2002, 5/2006, 3/2007
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Suunto X6M at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Suunto X6M in the language / languages: English as an attachment in your email.

The manual is 0,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Suunto X6M

Suunto X6M User Manual - German - 68 pages

Suunto X6M User Manual - Dutch - 67 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info