549834

Suntec Wellness Transform 10500 Manual

7
Zoom out
Zoom in
Previous page
1/13
Next page
7
COOLING
We recommend starting TRANSFORM early in the morning on warm days to get a cool room..
This TRANSFORM unit has a self-evaporation function for condensation water, so that it is normally not
necessary to empty the water tank in cooling mode. The drainage hose need not be connected. Please
make sure that the outlet is closed with the rubber cap during operation.
(This does not apply in the case of high air humidity. If the TRANSFORM unit operates in cooling mode for a longer period and
especially at a time of year with high air humidity, the condensation tank may be full. The control lamp will remind you to empty the
water. Refer to error message E4. In such a case, empty the water tank via the condensation water outlet. If continuous high air
humidity is likely, it is recommended to drain the condensation continuously via the drainage hose.)
COOLING IN INDOOR OPERATION
The TRANSFORM unit stands in the room to be cooled.
Connect the air hose and the air outlet grid to the TRANSFORM unit as displayed in the illustration; the air
hose connection piece and air outlet grid need to be exchanged.
The warm extract air must be emitted from the room via the air hose. This can be executed e.g. via a tilted
window, a door or wall aperture. Make sure that no warm outside air can enter the room. For effective
cooling, we recommend our selection of various accessories which reduce or prevent entry of warm air into
the room.
Set the function to „COOLING“. Set the target temperature using the temperature control. The settable
temperature range is between 17°C and 30°C target temperature. The TRANSFORM unit must only be
used in an ambient temperature of maximum 32°C.
Note: After switching on, or over, the ventilator operates, but the compressor only starts after the control lamp has flashed for 3
minutes. Cooling effect may require a further 10 minutes. Further information is available under the item, „Troubleshooting“.
COOLING IN OUTDOOR OPERATION
The TRANSFORM unit is outside the room to be cooled.
Connect the air hose and the air outlet grid to the TRANSFORM unit as displayed in the illustration; the air
hose connection piece and air outlet grid need to be exchanged.
Place the TRANSFORM unit in the shade if possible and in a cool place in order to increase efficiency and
to avoid overheating. At an ambient temperature of over 32°C, the TRANSFORM unit may deactivate. If th is
occurs continuously, we recommend you temporarily use the INDOOR OPERATION of the TRANSFORM
unit. We recommend that a drainage hose for condensation water be connected.
Set the function to „COOLING“. The settable temperature range is between 17°C and 30°C. This can be se t
using the temperature control.
The air with high oxygen content cooled by the TRANSFORM unit is led into the room via the air hose. This
can be executed e.g. via a tilted window, a door or wall aperture. Make sure that no warm outside air can
enter the room. We recommend that a drainage hose for condensation water be connected. For effective
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Suntec Wellness Transform 10500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Suntec Wellness Transform 10500 in the language / languages: English as an attachment in your email.

The manual is 1,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info