664813
18
Zoom out
Zoom in
Previous page
1/172
Next page
18
As soon as the water tank is full, the “WF” blinks on the display, the standby mode automatically turns
on, it will sound the warning alarm and all the buttons will be locked until the tank is emptied.
To empty of the water tank you need to remove the rubber stopper on the bottom of the unit and let the
water leak into a container.
Turn off the power and unplug the power cord. Once you reboot the device, it will work normally.
Cleaning
Before starting cleaning or maintenance, turn the power off by pressing the POWER button, wait a few minutes
and then unplug the power cord from the outlet.
Surface cleaning
Clean the unit using a damp cloth, and then wipe it using a dry cloth. Do not use chemical solvents (such as
gasoline, alcohol). The surface and the entire housing could be damaged.
Air filter cleaning
Clean the air filter regularly. If the air filter is clogged with dust, the efficiency of the device could be
reduced.
1) Open the air outlet and remove the filter.
2) Wash the air filter by submersion into warm water (about 40° C) with neutral detergent, rinse it under
running water and dry it with a soft cloth.
3) Install air filter carefully after cleaning and drying.
Storage
1. Pull the power plug and empty the water tank. Then set the device into the operating mode. Press the fan
button and hold it for a. 5 seconds until the device switches to low fan speed. Let the unit run in this mode for half
a day until the inner construction has dried. Thus, it will not become mouldy.
2. Turn off the unit and unplug the power cord.
3. Coil the cord and attach it to the holder.
4. Disconnect the exhaust tubing from the device and keep it safe.
5. Put the unit into a box and bring it to a dry place.
6. Remove the batteries from the remote control and keep them safe as well.
Troubleshooting
Don’t repair or disassemble the unit by yourself, unsuitable repair may make the quality-protected card in vain,
and even cause damage to the user or his/her possession.
Problems
Cause
1. The unit does not
turn on when you
press the Power
button.
Power cord is not plugged.
Water full indicator lamp blinks.
2. The unit restarts
again and again
Windows and doors are open, other
heat sources in the room (leading to
temperature variation)
Direct sunlight
Exhaust hose is disconnected or
blocked.
Air inlet is blocked by smth.
3. Noise
The unit does not stand on a flat
surface.
4. Compressor does
not start
Thermal protection function is
activated.
Spare parts and accessories supply (fast convenient supply)
You can obtain spare parts and accessories for your MOVE unit from your local dealer. And at our website
www.suntec-wellness.de
you will find further information on individual accessory products as well as information on obtaining our spare
parts quickly and conveniently. You will also find other information (e.g. FAQ, lists of spare parts, document
download, etc) about your MOVE unit.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Suntec Klimatronic MOVE plus 7.000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Suntec Klimatronic MOVE plus 7.000 in the language / languages: All languages as an attachment in your email.

The manual is 1,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info