514908
13
Zoom out
Zoom in
Previous page
1/220
Next page
13
ENGLISH
Adjusting the footrest
CAUTION!
Do not stand on the footboard!
Even if the user is
sitting in the chair, there is still a
risk of tipping over and injury.
CAUTION:
When transferring, do not stand
on the footboard, there is a risk
of tipping over and injury.

you to adjust the footrest to
correspond to the length of your
lower leg and re-attach the footrest.
The angle of the footrest may be
individually adjusted by loosening

on the footrest prevents the feet
slipping off accidentally. Make sure
that after any adjustment work, all


Footplate Adjustment
Adjusting the seat height
To adjust the rear seat height
release





reduce the length of the axle stem
as required.

NOTE:
An adjustment to the castor angle may be necessary when
adjusting the rear seat height .
Seat
High-mount footrest
The high-mount footrest is fitted on
the inner part of the frame
and permits a higher footrest position

Fig. 5.14
1
2
3
Seat sling
To tighten the upholstery, please use the straps below the
upholstery.
Link Rear Suspension
WARNING!
Rear suspension can affect the
stability of the wheelchair. To avoid a

when becoming familiar with new
equipment.
1. Tuning the 4-Link Rear
Suspension
a. To stiffen the suspension, turn the



b. To soften the suspension, turn the


suspension system from underneath

2. Alignment of Suspension Link
Arms

are set at the factory to ensure proper tracking
and performance of the 4-Link Rear Suspension system.
Setting the Toe to Zero



until the ball is centered in the level. The toe is now set at zero


tube is centered left-to-right relative to the wheelchair frame, and
the flat portions underneath outer camber tube clamp are
parallel side to side. The end of the camber tube should be flush
with the outer most portion of the camber tube clamp. Torque

Setting the Toe to Zero–
Alternative Method
Place the entire wheelchair on a flat
horizontal table or ground surface.

side, unless equipped with anti-tips

camber tube clamp. Locate the flat
surfaces on the front and rear of the

that is known to have an accurate


on the flat horizontal surface and up
against the flat of the camber plug.
Rotate the camber tube and plug
assembly until the flat surface of the
camber plug is parallel to the



tube is centered left-to-right relative to the wheelchair frame and
the flat portions underneath outer camber tube clamp are
parallel side to side. The end of the camber tube should be flush
with the outer most portion of the camber tube clamp. Torque the

NOTE– When turning the 4-Link Rear Suspension, always make
one change at time and write down the
change. This takes patience, but allows you to understand how
each change affects the ride of the
wheelchair in conjunction with rear suspension.
NOTE– Lower shock mount is designed to have a loose feel,
this is by design to allow for proper suspension travel.
NOTE
clamp to the shock camber clamp.
3. Maintenance
The maintenance requirements listed below should be followed
along with general wheelchair
maintenance called out in Section XI.
a. Do not apply lubrication to shock end bushings or coils.
b. You can apply lubrication to the link ends after cleaning with a
mild soap and soft
brush.
c. Use a soft brush to clear any dirt or debris from coil system.
d. Never use a high-powered washer for cleaning the 4-Link
Rear Suspension.
1
Fig. 5.11
Fig. 5.13
2
3
Fig. 5.12
Options - Snoll on
Please see extra manuall for Snoll on
Fig. 5.7
BALL
C
B
Fig. 5.9
PARALLEL
D
C
Fig. 5.10
H
I
G
E
F
Fig. 5.8
D
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sunrise Medical Helium 2013 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sunrise Medical Helium 2013 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info