654687

Sunbird Solar Solarpod Pro 1000 Manual

3
Zoom out
Zoom in
Previous page
1/4
Next page
Section 4
_______
_________________________________________________________________
CHARGING
Fully charge before first use. For maximum efficiency,
charge after each use or every 2
is being stored. Failure to properly charge as listed below could damage the
unit and affect
performance. CAUTION: ONLY USE CHARGERS PROVIDED WITH THE SOLARPOD
TM
DAMAGE MAY OCCUR.
Charging Indicator - Indicates Charging Rate
1.
Five yellow
LEDs represent the charging rate when using any of the methods of charging
below.
2.
Each yellow
LED equals approximately 20% charge rate. This will help you to position a solar
panel in the best angle to the sun. If the Solarpod™ Pro 1000
is plugged into a 1
or 12V - 24VDC power source, all 5 LEDs should be illuminated.
Battery Indicator - Indicates Battery Capacity Level
1.
Five blue LEDs represents the current battery capacity.
2.
Each blue LED represents approximately 20% full.
Solar Charging (recommended Sunbird Solar 120W Solar Panel)
1.
The Solarpod™ Pro 1000 has built-
in battery protection and does not require a solar charge
controller.
2.
Place the solar panel in direct sun.
3.
Connect the solar charging cable (included) male pin tip to the DC IN port
on the
Pro 1000. Connect the MC4 (+) and (-) tips to the solar panel.
4.
Adjust the solar panel so that it is directly facing the sun.
Charging will begin immediately
the yellow charging LED indicators will illuminate.
5.
To ensure full battery charge, continue charging for 1 additional hour.
6.
To maximize battery cycle life, disconnect when Solarpod™ Pro 1000
is fully charged.
AC Wall Charging (Adapter Included)
1.
Connect the male pin tip of the AC Wall Charger into the DC IN port of the
Solarpod
and then plug the other end into an electrical outlet.
2.
The charging indicator on the AC Wall Charger
will illuminate red when charging is in process
and green when the Solarpod™ Pro 1000 has reached a full charge.
3.
The yellow charging LED indicators will also illuminate.
4.
To ensure full battery charge, continue charging for 1 additional hour after
1000 is fully charged.
5.
There is no need to disconnect AC Wall Charger when charging is complete.
Connecting Charging Lines to the Solarpod™ Pro 1000
1.
Align head tabs with DC IN socket on back of unit.
2.
Turn head clockwise until the silver lock tab is a
t top and press lock tab toward unit.
3.
To unplug charging head, follow the above steps in reverse order.
1. Align Tabs
.
2. Turn Clockwise
3. Press in Lock
_________________________________________________________________
charge after each use or every 2
months if it
unit and affect
TM
PRO 1000 OR
LEDs represent the charging rate when using any of the methods of charging
LED equals approximately 20% charge rate. This will help you to position a solar
is plugged into a 1
00V – 240VAC
in battery protection and does not require a solar charge
on the
Solarpod™
Charging will begin immediately
and
is fully charged.
Solarpod
™ Pro 1000
will illuminate red when charging is in process
To ensure full battery charge, continue charging for 1 additional hour after
Solarpod™ Pro
There is no need to disconnect AC Wall Charger when charging is complete.
t top and press lock tab toward unit.
Section 5
________________________________________________________________________
OPERATING INSTRUCTIONS
Once charged, the Solarpod™ Pro 1000
is ready to use right out of the box. No set up is required.
All outputs may be used simultaneously. Check your device’s specifications to make sure they are
compatible with the Solarpod™ Pro 1000.
ON/OFF Button - When on, the switches
surrounding LED
AC Power Button - When on, the switches
surrounding LED
USB Operation
• Turn the ON/OFF BUTTON on.
•
Plug in your device’s USB power or charging
•
A combined 5V/2A maximum output is available between the two ports (when fully
charged).
•
Disconnect and power off when not in use
AC Operation (max 1000W output)
• Press the AC power button
to activate the inverter
•
Plug in your device’s power or charging cable into the electrical
• Disconnect and turn off the
power when not in use
• CAUTION
: CHECK CAREFULLY THAT THE VOLTAGE RATING OF YOUR APPLIANCE MATCHES
THE VOLTAGE RATING OF THE
Solarpod™ Pro
• CAUTION
: Using devices rated higher than
minutes may cause the Solarpod™ Pro
1000
cooled the circuit will reset and the
Solarpod™ Pro
Advantages of a Pure Sine Wave Inverter
•
A pure sine wave inverter produces a nearly perfect sine wave output (less than 3%
total harmonic distortion) that is essentially
• Eliminates electrical
interference, overheating and noise.
•
Computer crashes and other appliance operational glitches can be avoided.
• Inductive loads such as variable-
speed motors and microwave ovens can be used,
and supports in running them quieter and cooler.
• Some appliances
and sensitive electronics will simply not work properly without
pure sine wave power.
•
Reduces audible and electrical noise in fans, fluorescent lights, magnetic circuit
breakers and electronic gears.
12V DC Operation (Max 15A output)
• Turn the ON/OFF BUTTON on.
•
Plug in your 12V device’s power or charging cable into the 12V Vehicle Socket
• Neither power button need to be on.
•
Disconnect and power off when not in use
________________________________________________________________________
is ready to use right out of the box. No set up is required.
All outputs may be used simultaneously. Check your device’s specifications to make sure they are
surrounding LED
light will turn green.
surrounding LED
light will turn red.
Plug in your device’s USB power or charging
cable.
A combined 5V/2A maximum output is available between the two ports (when fully
Disconnect and power off when not in use
.
to activate the inverter
.
Plug in your device’s power or charging cable into the electrical
AC socket.
power when not in use
.
: CHECK CAREFULLY THAT THE VOLTAGE RATING OF YOUR APPLIANCE MATCHES
Solarpod™ Pro
1000 UNIT YOU HAVE PURCHASED.
: Using devices rated higher than
900-1000W and operated for more than 10
1000
to overheat and shut down. Once it has
Solarpod™ Pro
1000 will be operational again.
A pure sine wave inverter produces a nearly perfect sine wave output (less than 3%
total harmonic distortion) that is essentially
identical to utility-supplied grid power.
interference, overheating and noise.
Computer crashes and other appliance operational glitches can be avoided.
speed motors and microwave ovens can be used,
and supports in running them quieter and cooler.
and sensitive electronics will simply not work properly without
Reduces audible and electrical noise in fans, fluorescent lights, magnetic circuit
Plug in your 12V device’s power or charging cable into the 12V Vehicle Socket
.
Disconnect and power off when not in use
.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sunbird Solar Solarpod Pro 1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sunbird Solar Solarpod Pro 1000 in the language / languages: English as an attachment in your email.

The manual is 0,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info