Manual Sunbeam MX9600Z Zumbo Limited Edition Mixmaster (page 6 of 26) (English)

654204

Zoom out

Zoom in

1/26

MX9600ZP

MX9600ZW

MX9600ZM

Important instructions – retain for

future use.

Contents

Sunbeam’s Safety Precautions 2

Features of your Zumbo Limited Edition Mixmaster

Using your Zumbo Limited Edition Mixmaster

Using your Power Drive 10

Safety Mechanisms 11

Care & Cleaning 12

Mixing Guide 13

Oven Temperature Guide 14

Troubleshooting Guide 15

Ingredients 16

Cookery Tips for Best Results 17

Making a Successful Dough 18

Sunbeam’s Safety Precautions

Sunbeam are very safety conscious when designing

and manufacturing consumer products, but it is

essential that the product user also exercise care

when using an electrical appliance. Listed below are

precautions which are essential for the safe use of an

electrical appliance:

• Read carefully and save all the instructions

provided with an appliance.

• Always turn the power off at the power outlet before

you insert or remove a plug. Remove by grasping

the plug - do not pull on the cord.

• Turn the power off and remove the plug when the

appliance is not in use and before cleaning.

• Do not use your appliance with an extension cord

unless this cord has been checked and tested by a

qualified technician or service person.

• Always use your appliance from a power outlet of

the voltage (A.C. only) marked on the appliance.

• This appliance is not intended for use by young

children or infirm persons unless they have been

adequately supervised by a responsible adult to

ensure that they can use the appliance safely.

• Young children should be supervised to ensure that

they do not play with the appliance.

• Never leave an appliance unattended while in use.

• Do not use an appliance for any purpose other than

its intended use.

• Do not place an appliance on or near a hot gas

flame, electric element or on a heated oven.

Do not place on top of any other appliance.

• Do not let the power cord of an appliance hang over

the edge of a table or bench top or touch any hot

surface.

• Do not operate any electrical appliance with a

damaged cord or after the appliance has been

damaged in any manner. If damage is suspected,

return the appliance to the nearest Sunbeam

Appointed Service Centre for examination, repair or

adjustment.

• For additional protection, Sunbeam recommend

the use of a residual current device (RCD)

with a tripping current not exceeding 30mA in

the electrical circuit supplying power to your

appliances.

• In order to avoid a hazard due to inadvertent

resetting of the thermal cut-out, this appliance

must not be supplied through an external switching

device, such as a time, or connected to a circuit

that is regularly switched on and off by the utility.

• Do not immerse the appliance in water or any other

liquid unless recommended.

• This appliance is intended to be used in household

and similar applications such as: staff kitchen areas

in shops, offices and other working environments;

farm houses; by clients in hotels, motels and other

residential type environments; bed and breakfast

type environments.

If you have any concerns regarding the performance and use of your appliance,

please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line.

Ensure the above safety precautions are understood.

SAFETY PRECAUTIONS FOR YOUR SUNBEAM

Zumbo Limited Edition

PLANETARY

MIXMASTER

BENCH MIXER.

• Switch off the appliance and disconnect from

supply before changing accessories or approaching

parts that move in use.

• Never remove any attachment or accessory when

the appliance is in operation; including the beater,

Scrapemaster

™

spatula beater, whisk, dough hook,

pasta roller, pasta cutter.

• Ensure fingers are kept well away from moving

beater, Scrapemaster

™

spatula beater, pasta roller,

pasta cutter, whisk or dough hook.

• Ensure that the bowl is secured and locked onto

the base of the Bench Mixer before commencing

mixing.

• Do not unlock or remove the mixing bowl from the

base of the Power Drive Bench Mixer whilst in use.

• Never tilt back the head of the Power Drive Bench

Mixer whilst the appliance is in operation.

• When using extremely heavy loads the appliance

should not be operated for more than 1 and a half

minutes. This does not apply to the recipes detailed

in this booklet.

• Ensure long hair is tied back and young children

are not near the bowl.

Features of your Zumbo Limited

Edition Mixmaster

Bench Mixer

Drive Outlet

The drive outlet allows for the attachment of a range

of accessories including pasta rollers and pasta cutters.

1200W motor

Powerful motor achieves thorough mixing results.

Full die-cast metal body with sintered metal gears

The heavy duty die-cast metal body combined with sintered

metal gears deliver quality, style and superior performance.

Planetary mixing action

Enables the mixing attachment (beater, Scrapemaster

™

spatula beater, whisk or dough hook) to rotate whilst

travelling around the inside of the bowl, and reach all

areas of the bowl ensuring ingredients are completely mixed.

Splashguard with pouring chute

Splashguard prevents ingredients from spilling out of the

mixing bowl. The pouring chute allows adding ingredients

directly into the mixing bowl without having to stop the

mixer and lifting the mixer head.

Overmould Handle

The handle on the mixing bowl allows for ease of use during

operation and the overmould handle provides comfort for your hand.

Slow start

The mixing speed is gradually increased to prevent ingredients

splashing out of the mixing bowl.

Stainless steel mixing bowl

The 4.5L mixing bowl is ideal for mixing large

or small quantities of ingredients.

Cord storage

For added convenience the unused cord length can easily be pushed

into the base of the mixer for storage.

Pause / Start button

Allows you to instantly stop the mixer to assess the mixing progress

and/or add additional ingredients without affecting

the timer.

Carrying grips

Grips at both sides of the mixer base allow for easy carrying.

Die-cast alloy dough hook

Takes the hard work out of kneading dough and other

heavy mixtures.

Super Scraper Whisk

The unique design of the whisk allows more air to be

added to ingredients when whisking, providing faster

results.

Head release with in-built safety feature

The mixer head can be easily released and lifted

with one hand. It tilts upwards and locks securely

into position to allow easy insertion and removal of

the mixing bowl and attachments. The in-built safety

feature ensures that the mixer only starts when the

mixer head is tilted downwards and securely locked

in. Lifting the mixer head during the mixing process

will automatically cut power to the motor.

Scrapemaster™ spatula beater

Excels at combining ingredients and simultaneously

scrapes the sides and the bottom of the mixing bowl,

virtually eliminating hand-scraping and batter build-up

on the blade. Superior bowl clearance also makes this

attachment ideal for smaller mixing quantities.

Die-cast alloy beater

Provides maximum aeration for creaming butter and

sugar, and is also ideal for mixing heavy cake mixes.

LCD screen with timer

LCD screen displays mixing time and speed setting.

Timer function can be set to count up or down as

required.

Speed control dial with 12 variable settings

The combination of 12 electronic speeds and a

powerful torque control motor ensures superior mixing

control and maintains speed, regardless of the mixing

load.

Buttons

' ' and ' ' buttons can be used to choose

the desired mixing duration, or to set the

kitchen timer.

Before using your Power Drive Bench Mixer

for the first time, remove any packaging

material and promotional labels or tags.

Please also remove the plastic plug pin cover

before using the mixer. It is recommended to

wash the mixing bowl, beater, Scrapemaster

™

spatula beater, whisk and dough hook in

warm soapy water with a soft cloth. Rinse

and dry thoroughly.

Set-up of your bench mixer

Before assembling your Power Drive Bench

Mixer, be sure the power cord is unplugged

from the power outlet. Position the mixer on

a level, dry surface such as a bench top.

1. Press the ‘head release’ button, located at

the rear of the mixer head. This will release

the mixer head out of its locked position.

Ease the mixer head backwards until it

locks into its tilt position (Fig. 1).

2. Select the desired attachment depending

on the mixing task to be performed:

– Beater for creaming butter and

sugar, plus mixing heavy cake

mixes.

– Scrapemaster

™

spatula beater

for smaller amounts of mixture

or for faster creaming of butter

and sugar and heavy cake

mixes. Also great for folding

ingredients

– Whisk for whisking cream, egg

whites, light batters and packet

cake mixes.

– Dough hook for kneading dough

and other heavy mixtures.

3. Attach the selected attachment onto the

drive outlet using the bayonet attachment.

Place the attachment into position with the

feeder roll at the back. Simply push the

roller back and down, to lock into position.

Note: Be sure the attachment is locked firmly

in place.

Using your Zumbo Limited Edition

Mixmaster

Bench Mixer

Figure 1

Figure 2

Figure 3

4. Place the bowl on the base with the handle

facing you. Then gently rotate the bowl

in a clockwise direction until it locks into

position (Fig 3). The bowl should feel firm

with no movement.

5. Lower the mixer head with the selected

mixing attachment in place into the mixing

bowl. Press the ‘head release’ button to

un-lock it from its position and ease the

mixer head down (Fig. 4).

6. The splashguard can now be placed over

the bowl if desired (Fig 5).

Using your Planetary Mixmaster

Bench Mixer

1. Position the mixer on a level, dry

surface such as a bench top. Ensure the

mixing bowl is in place and the desired

attachment is inserted.

2. Plug the power cord into a 230/240 Volt

AC power outlet.

3. A beep will sound and the LCD screen

will light up to inform you that the mixer

is now switched on. The LCD screen

will flash three times and the timer will

display “00:00”. The screen will also

display the speed setting. If the LCD

displays a speed setting other than “0”

and continues to flash, you may turn the

speed control dial anti-clockwise to the

“0” position to re-set the speed setting.

4a. If using the splashguard, add ingredients

to the mixing bowl through the pouring

shoot.

4b. If using the mixer without the

splashguard, release the mixer head

out of its locked position and ease it

backwards until it locks into its tilt

position. Add ingredients to the mixing

bowl. Then, un-lock the mixer head and

lower it forward into the mixing bowl.

5. Turn the speed control dial clockwise to

commence mixing (Fig. 6), or, if a speed

is already set, press the button.

Using your Zumbo Limited Edition Mixmaster

Bench Mixer continued

Figure 4

Figure 5

Figure 6

Using your Zumbo Limited Edition

Mixmaster

Bench Mixer

The LCD screen will display the chosen speed

setting. Instructions for mixing speeds for

each type of mixture are shown in the ‘Mixing

Guide’ on page 15.

6. When mixing is complete, turn the speed

control dial anti-clockwise to the ‘0’

position (Fig. 7) and unplug the cord from

the power outlet.

7. Remove the splashguard if positioned on

the bowl.

8. Press the ‘head release’ button and ease

the mixer head back until it is locked into

the tilt back position

(see Figure 1 on page 6).

9. To remove the particular mixing

attachment, push it upwards, turn it anti-

clockwise, then pull it downwards (Fig 8).

Using your Zumbo Limited Edition Mixmaster

Bench Mixer continued

Figure 7

Figure 8

Using your Zumbo Limited Edition Mixmaster

Bench Mixer continued

Pause mode

At any stage during your mixing task you

can pause the mixer. This enables you to

assess the mixing progress, scrape any food

mixture down the sides of the mixing bowl

with a spatula, or add additional ingredients -

without affecting the timer.

Pause the mixer during operation by pressing

the at the front of the speed control

dial.

The time on the LCD screen will flash

continuously, displaying the mixing time at

which the mixer has been paused.

In pause mode, you are able to reset or

adjust the timer if desired. Please see details

on the Count-up and Count-down timer

features below.

To resume your mixing task, simply press

the button again. The mixer will

resume mixing at the same speed setting,

and the timer will resume counting up/down

depending on your selection made.

Count-up timer

The count up timer informs you how long

your ingredients have been mixing for. The

next time you mix the same ingredients you

can then set the count-down timer for the

specific time.

As soon as you start mixing, the timer will

automatically start to count up.

The maximum mixing time is 20 minutes

and will be displayed on the LCD screen as

“20:00” (twenty minutes, zero seconds).

The mixer will automatically stop mixing after

20 minutes and beep twice.

The screen will flash for about 5 seconds.

The timer will automatically re-set to

“00:00”.

The LCD screen will display the speed

setting that it stopped at and this setting will

continue to flash.

If you pause the mixer at any time during the

mixing process by pressing the button

at the front of the speed control dial, the

mixing time displayed on the LCD screen will

flash until you resume mixing by pressing the

button again.

To reset the timer to “00:00”, turn the speed

control dial anti-clockwise to the “0” location

or, when paused, press the ‘+’ and ‘-’ buttons

simultaneously.

Using your Zumbo Limited Edition Mixmaster

Bench Mixer continued

Count-down timer

The count-down timer is especially useful

when following a recipe that specifies mixing

times.

The ‘+’ and ‘-’ buttons allow you to choose

the desired mixing duration. Press the

‘+’ button and you will add 30 seconds.

Press the ‘-’ button and you will reduce the

previously set mixing time by 30 seconds.

For example, if a recipe calls to “beat for

2 minutes”, you can set the count-down

timer to 2 minutes. Simply press the ‘+’

button until “02:00” is displayed on the LCD

screen, i.e. press the ‘+’ button four times.

If you would like to change the countdown

time after your initial setup, press the

button, then press the ‘+’ and ‘-’ buttons to

increase or reduce the mixing time to the

nearest 30 sec increment.

For example, you set the count-down timer

to 3 minutes and turn the speed control dial

to start mixing on a chosen speed. After 1

minute, 25 seconds, you pause the mixer by

pressing the button. The LCD displays

the remaining count-down time of 01:35. If

you now press the ‘+’ button once to increase

the mixing time, the display will show 02:00

(which is the nearest 30 sec increment).

To reset the timer to “00:00”, turn the speed

control dial anti-clockwise to the “0” location

or, when paused, press the ‘+’ and ‘-’ buttons

simultaneously.

When the chosen mixing time is completed,

the mixer will beep twice to inform you that

the time has expired. It will stop mixing

automatically. The timer display “00:00”

and the LCD screen will flash for about 5

seconds. The LCD screen will display the

speed setting that it stopped at and this

setting will continue to flash.

If you need to resume mixing, simply press

the button or, alternatively, reset the

mixer by turning the dial to “0”, and then

turn the dial clockwise.

Kitchen Timer function

The timer function can be used without

mixing as a kitchen timer or stopwatch.

Timer: Set the time as described in the

Count-down timer section on page 9, then

press the button while the dial is in “0”

(i.e. no speed selected).

When the set time expires, the mixer

will beep and the LCD screen will flash

continuously until the button is pressed.

Stopwatch: Simply press the button

whilst in “0” (i.e. no speed selected). The

maximum time the LCD screen can display

is 90 minutes and will be displayed on the

LCD screen as “90:00” (ninety minutes, zero

seconds).

When the maximum time has been reached,

the mixer will beep and the time display on

the LCD screen will flash continuously until

the button is pressed.

To reset the timer to zero (“00:00”), press

the button, then press the ‘+’ and ‘-’

buttons simultaneously.

Using your Power Drive

Set-up of your Power Drive

Before assembling your attachments to

the Power Drive, be sure the power cord is

unplugged from the power outlet. Position

the mixer on a level, dry surface such as a

bench top.

1. Remove the storage cover from the front

of the mixer head by pulling down on the

cover. (See Fig. 1).

Store the cover in the storage location at the

back of the mixer head'.

2. Select the desired attachment depending

on the task to be performed. Refer to

the instruction and recipe booklet for the

accessory, for more details.

•

use the pasta roller to roll pasta dough into

sheets. This attachment is always used as

first step when making pasta.

•

the spaghetti pasta cutter cuts pasta

sheets into pasta strands.

•

the tagliatelle pasta cutter cuts pasta

sheets into wider pasta strands.

Thermo cut-off – temperature overload

The mixer is equipped with a self-resetting

safety device which safeguards against

overheating the motor with excessive

loads. If overheating occurs, the mixer

will automatically activate the overheating

protection device and switch itself off. The

mixer will beep and the screen will flash

continuously. Switch the mixer off and

unplug it from the power point. Release the

mixer head and tilt it back until it is locked

into the tilt back position. Let the mixer rest

for 30 min.

Electronic protection cut-out

If the mixing load is too heavy for the

selected speed and prevents the attachment

from rotating, the mixer will cut-out to

prevent damage to the unit. If the LCD

screen flashes fast and continuously, the

motor has not been able to achieve or

maintain the set speed. In this case, unplug

the mixer and remove some of the mixture

from the bowl, working in batches.

Mixer head safety mechanism

The mixer head must be locked down or the

motor will not operate. If the mixer head is

tilted upwards during operation, the mixer

will automatically stop. This is a safety

mechanism to avoid injury. To resume your

mixing task, lock the mixer head back down

and press the button.

Standby mode

The mixer will automatically switch off the

LCD screen after 20 minutes to save power.

To exit the standby mode, press any button or

turn the dial.

Safety Mechanisms

Before cleaning your Zumbo Limited Edition

Mixmaster

, ensure that the power is turned

off at the power outlet, then remove the plug.

Wipe over the outside area of the Planetary

Mixmaster

including the head and base,

with a dampened cloth and polish with a soft

dry cloth.

Wipe any excess food particles from the

power cord.

Sunbeam recommends to wash the mixing

bowl, splashguard, beater, Scrapemaster

™

spatula beater, whisk and dough hook in

warm soapy water and wipe dry – use a

brush if necessary to remove any sticky food

particles.

All plastic components deteriorate through

prolonged dishwasher use. However, parts of

your Mixmaster

are tolerant to dishwasher

use. These include the stainless steel mixing

bowl, beaterand dough hook.

Note: Place only on the top rack of the

dishwasher.

Stainless steel whisk

After washing the stainless steel whisk, the

outer wire may have moved out of position

and become misaligned (see Figure 9).

Please clip the outer wire back into position

(see Figure 10).

Maintenance Service

Your Zumbo Limited Edition Mixmaster

should be regularly checked. After

approximately four years of domestic use, the

grease in the gear compartment should be

examined. We suggest at that time you send

the mixer to your nearest Sunbeam Appliance

Service Centre to ensure efficient, correct

servicing.

Storage

Keep your Zumbo Limited Edition Mixmaster

in a convenient position on your kitchen

bench ready for use at all times. Place the

beater, Scrapemaster

™

spatula beater, whisk

and dough hook in the mixing bowl as storage

of these attachments in a drawer with other

kitchen equipment may cause damage.

Note: Never wind the power cord around the

mixer after use as the warmth from the motor

may cause damage to the power cord. For

added convenience the unused cord length

can easily be pushed into the base of the

mixer for storage.

Care and Cleaning

Figure 9

Figure 10

Troubleshooting Guide

Problem Possible Cause What to do

Motor will not start. Motor is over-heated.

Mixer head is not

locked down properly.

Unplug and allow motor to cool, (the mixer head

should be cool to touch).

Move mixture in mixing bowl to the side of the

attachment, to allow the attachment to go all the

way into the bowl.

Motor is over-heated. Use of a high speed

for a long time.

Mixture too heavy.

Mixing quantity too

large.

Unplug and allow motor to cool, (the mixer head

should be cool to touch).

Try mixing in batches.

Mixer head does not

lock down properly.

Thick mixture is

preventing the

attachment from

going all the way

down into the bowl.

Move mixture in mixing bowl to the side of the

attachment, to allow the attachment to go all the

way into the bowl.

Attachment is

hitting the bowl.

Attachment is not

inserted correctly.

Mixing bowl is not

locked into the base

properly.

Remove the attachment and try inserting again.

Refer to the instructions in this booklet if needed.

Lock bowl into position. Refer to the instructions

in this booklet if needed.

Mixer is moving on

the benchtop.

Chosen speed is too

high for the mixture.

Mixture caught up in

the attachment.

Flour or spills on

bench top.

Lower the speed or mix in batches.

Scrape down the attachment and continue mixing.

Clean and dry benchtop as well as the mixer base.

Cannot use or set

the timer, but the

motor will start when

the speed dial is

being turned.

‘+’ button, ‘-‘ button

or Pause/Start button

was depressed when

the unit was switched

on.

Unplug from the power outlet for 5-10 seconds,

then plug in again ensuring no buttons are

pressed.

If this problem persists, there may be food

particles or liquid in the switch. The unit is

safe to use in this mode, however Sunbeam

recommends to take the product to an authorised

service centre. For a complete list of Sunbeam’s

authorised service centres visit our website www.

sunbeam.com.au or www.sunbeam.co.nz

or call: Australia: 1300 881 861

New Zealand: 0800 786 232

SPEED SETTING RANGE MIXING TASK

LOW

1-4

FOLDING & KNEADING

Combining or initial mixing of ingredients

Folding

Kneading – doughs (pastry, bread, scones, etc.)

MEDIUM

5-7

LIGHT MIXING

Kneading – heavy doughs

Beating – sugar and butter, cake mixes

HIGH

8-10

CREAMING & BEATING

Whisking – light batters

Beating – heavy batters/icing

VERY HIGH

11-12

WHIPPING & AERATING

Whisking – egg whites/cream

Please keep in mind that the various mixing tasks and related speeds, listed in the table

below, may vary slightly from recipe to recipe. Please refer to it regularly as you develop your

understanding of how different ingredients interact when mixing.

NOTES:

For most recipes, it is better to begin

your mixing on a slower speed until the

ingredients begin combining, then move to

the appropriate speed range for the particular

task.

Generally, there is not one set speed for an

entire recipe. You will need to change the

speed of the mixer depending on what stage

of the recipe you are working on. This is

communicated in the recipe section.

When mixing larger quantities you may

need to increase the mixer speed due to the

amount of mixing required and the larger

load on the machine.

When making a recipe that requires the

addition of dry ingredients, such as flour,

slow the speed down whilst these ingredients

are being added to avoid a snow storm

effect. Once the additional ingredients

begin combining then slowly increase to the

appropriate speed for the particular mixing

task.

Mixing Guide

Oven Temperature Guide

DESCRIPTION OF

OVEN TEMPERATURES

Degrees Celcius °C Degrees Fahrenheit °F Gas Mark

Very Slow 120 250 ½

Slow 140-150 300 1-2

Moderately Slow 160 325 3

Moderate 180 350 4

Moderately hot 200 400 6

Hot 220 425 8

Very Hot 240 475 9

For your information, the following temperature settings are included as a guide.

Note: If using fan forced ovens be sure to turn the temperature down by 20°C.

Also check recipes at the back of this booklet.

Measuring Ingredients

Careful and correct measurement of all

ingredients is essential for recipe success

(particularly when baking). Australian

Standard Metric cup and spoon measures are

used in all recipes in the book. All cup and

spoon measurements should be level.

• One metric tablespoon is equal to 20mls.

• One metric teaspoon is equal to 5mls.

• One liquid cup measurement is equal to

250mls.

• All eggs used in our recipes are extra large

(59g) eggs, unless otherwise specified.

The following are some hints on measuring

ingredients.

When measuring wet ingredients, always

use a measuring jug or if measuring small

quantities, use a standard metric measuring

spoon. Place the measuring jug on a level

surface and check the measurement at eye

level.

When measuring dry ingredients, always use a

standard metric measuring cup or standard

metric measuring spoon. Shake gently to

ensure there are no air pockets and level the

surface with a knife or metal spatula. Never

tap the cup on the bench or pack in the

ingredients (unless specified); this will give

an inaccurate measurement.

Note: crush any lumps, particularly in

bicarbonate of soda or sugar before

measuring.

When measuring other ingredients, always

weigh in grams using metric scales. To

ensure an accurate reading, always remember

to “tare” the scales back to zero with the

empty container before adding any food.

Tips for substituting Ingredients

• Unsalted butter is best for cake baking,

however it can be substituted with salted

butter or margarine if necessary. Margarine

may slightly alter the texture of the final

result.

• Self raising flour = plain flour + baking

powder (1 cup self raising flour = 1 cup

plain flour + 2 teaspoons baking powder)

• 1 cup plain flour + 1 teaspoon baking

powder = ½ cup plain flour + ½ cup self

raising flour

• When substituting wheat flour with gluten

free flour, the best results are usually

achieved in recipes that have a small

amount of flour.

• Commercial baking powders can contain

wheat starch. If your allergic to wheat,

you can make you own. Baking powder

= 1 teaspoon bicarbonate of soda + 2

teaspoons cream of tartar

• Icing sugar mixture can contain wheat

starch (this prevents it going lumpy). If you

have a gluten intolerance, pure icing sugar

can be used instead.

• Sultanas can be substituted with equal

measure of another dried fruit (best if they

are chopped to size).

• Golden syrup can be substituted with equal

measure of treacle or molasses

• 1 cup buttermilk = 1 cup fresh milk + 2

teaspoons vinegar or lemon juice.

• Milk can be substituted with soy milk. It

can sometimes also be replaced with fruit

juice acting as the liquid component.

• 7g dry yeast (1 sachet) = 15g compressed

yeast

Ingredients

General tips

• Before starting any recipe carefully read it

through from beginning to end.

• Ensure you have all ingredients and

utensils before you start.

• Refrigerated ingredients such as butter,

cream cheese and eggs should be at

room temperature for best results (unless

otherwise specified). Set these out ahead

of time. If you forget to remove butter from

the fridge, use the coarse side of a grater

to grate the butter. This will assist the

mixer and soften the butter faster.

• Always adjust the oven shelf to the desired

position and then preheat oven to baking

temperature recommended in the recipe.

Get to know your oven. Most ovens have

“hotspots” and it may be necessary to

turn food or swap shelves during cooking.

However, be aware that every time you

open the oven, the temperature drops.

Only open the oven if necessary and be

sure to close the door quickly.

• Break eggs into a small bowl before adding

to mixture. This eliminates the chance of

contaminating mixture with shells or rotten

eggs.

• All recipes have been carefully developed

and tested, but should you find it

necessary to alter the ingredients or tin,

you must allow for a variation in cooking

time. Always test for doneness in baked

goods before removing from oven or other

cooking appliance.

• During mixing, ingredients may splash to

the sides of the bowl. Pause the mixer and

use a rubber or plastic spatula to scrape

the bowl. NEVER USE A KNIFE, METAL

SPOON OR FORK, as these can damage

the beater and bowl. A light scraping after

the addition of each ingredient assists in

achieving efficient mixing.

Tips for cakes, biscuits and slices

• When cooked, a cake should shrink slightly

from the pan.

• When testing most cakes (not sponges,

fruitcakes or cheesecakes), gently touch

the surface; it should feel firm. At this

stage, remove the cake from the oven and

close the oven door to retain the heat.

Insert a thin skewer into the deepest

part of the cake. When cake is done, no

uncooked mixture should adhere to it.

• Testing cake doneness should be done

quickly. If the cake needs to be returned

to the oven, the oven door should be

open for minimal amount of time. Rapid

temperature change may cause an

undercooked cake to sink in the middle

• For most types of biscuits, you can test

if they are cooked by gently pushing the

biscuit on the tray with your finger. If it

moves without breaking, the biscuit is

cooked.

• Do not over beat any mixture. Be careful

that you only mix/blend mixtures for the

specified time. When folding, do so until

just combined. Over beating or mixing can

cause toughness, close texture, excessive

shrinkage or effect rising.

• Curdling can sometimes occur when

adding eggs to a mixture. If this happens,

continue with the recipe as it will come

back together when the dry ingredients are

added.

• If cakes begin to overbrown, cover the top

loosely with foil to protect it from the top

element of the oven.

• To obtain the greatest volume when beating

egg whites, be sure the bowl and beater

are completely clean and dry before use.

The smallest amount of grease or water can

prevent the whites from aerating.

Cookery Tips for Best Results

• The term “soft peaks” means that the egg

white barely supports itself. When the head

of the mixer is lifted, the egg white mixture

will curl and may fall from the beater.

• The term “firm peaks” means that the egg

white holds its shape. When the head of

the mixer is lifted, the egg white mixture

will remain pointy and firm.

• When making pavlova or other meringues,

always use caster sugar as it dissolves

much easier than other coarser sugars.

Sugar should begin being added at soft

peaks. If you wait until the egg whites

reach firm peaks and are dry, it will take

longer to dissolve the sugar.

• To test if sugar is dissolved, rub a small

quantity of mixture between your fingertips.

If it feels grainy, continue beating until

smooth.

• In general, cakes should be cooled on a

wire rack after the suggested standing

time. The standing time is to prevent

the freshly baked cake from splitting or

cracking when removed from the pan.

• Fruit cakes and various other heavy cakes,

such as mud cakes, are best cooled in the

pan. Due to the weight of these cakes,

turning out while still warm will cause

them to split. Cooling in the pan also

keeps them moist.

• Sponges should be removed from the pan

as soon as they come out of the oven.

• Most biscuits are best cooled on the baking

tray.

Cookery Tips for Best Results continued

Making a Successful Dough

Yeast

Yeast is a raising agent used in dough. It

is a microscopic living organism that grows

rapidly in suitable warm, moist conditions.

The yeast feeds on sugar and expels carbon

dioxide which expands the gluten framework.

When foaming yeast, the liquid should be

warm; about 26°C. If the liquid is too cold it

will retard the yeast growth. If it is too hot it

will kill the yeast.

Preparing the yeast

For the dry yeast to be activated it needs

to ferment. To do this, place warm liquid

and sugar into a bowl. Add dry yeast and

mix. Stand in a warm, draft-free place

until mixture starts to foam or bubble. This

process will take about 10 minutes.

Note: If dried yeast has not been stored

properly, has been exposed to light, extreme

heat, or is out of date, it may be dead or

inactive and it will not ferment. If the yeast

does not foam, your dough will not rise.

Preparing the dough

1. Insert dough hook (refer to page 6). Place

the dry ingredients into the bowl and lock

the bowl onto the base.

2. Turn the speed dial to low speed (1-4),

and gradually add the liquid ingredients

(including the pre-prepared yeast mixture)

to the bowl. When the ingredients start

to form a ball, stop the mixer and use a

rubber or plastic spatula to scrape down

the sides of the bowl if necessary.

3. Knead on low speed (1-4) (depending on

the amount of dough) until smooth and

elastic; for about 5-8 minutes.

4. Transfer dough to a large, well greased

mixing bowl. Cover the bowl with a light

cloth or plastic wrap and place it in a

warm, draft-free area until the dough

doubles in size.

5. Plunge fist into the centre of the risen

dough to punch out excess air. Fold outer

edges into the centre and turn dough out

onto a lightly floured surface. Cut and

shape dough to form buns, rolls or freeform

loaves and place on prepared baking trays.

Alternatively, place dough into prepared

bread tins. For pizza dough, it is now ready

to be rolled, topped and baked.

6. For the final rising of the bread dough,

cover the shaped dough with a light cloth

and place in a warm, draft-free area until

doubled in size again. Glaze and bake.

Making a Successful Dough continued

Tips

To add interest to breads.

• Brush dough with a little milk and sprinkle

loaves or buns with poppy, caraway or

sesame seeds before baking.

• Sprinkle loaves with shredded cheese

during the last few minutes of baking.

• Drizzle cooled, sweet tea rings or buns

with icing, or dust with icing sugar before

serving.

Glazes

Glazes may be brushed over the dough

before, during or after baking.

For a shiny crust, brush with cream or

evaporated milk before baking; or with warm

sieved apricot jam after baking.

For a glossy crust, brush with beaten egg

white before baking.

For a matt finish, brush with melted butter or

margarine after baking.

Questions & Answers:

Q. My mixture seems a little dry and crumbly.

Do I need to add more water?

A. Some flour tends to absorb or want more

moisture/liquid, especially on warm or humid

days. Add more water, a drop at a time, until

you reach a smooth ball/dough.

Q. I added too much water and my dough is

very sticky, what can I do?

A. If the dough is smooth without lumps,

add a little flour at a time and knead the

dough until it is smooth, soft to the touch

and bounces back when pressed with the tip

of your finger. Dough should not be sticky to

touch.

Q. My yeast did not bubble or foam, why?

A. The yeast may be dead or inactive, in

which case you will need to replace it. This

occurs when the liquid added or the standing

position was too hot or too cold. It can also

be because the yeast is out of date. If the

yeast does not foam, your dough will not rise.

Q. My dough did not rise, why?

A. If the yeast fermented properly, you may

just need to place the bowl in a warmer

position. Covering the bowl with plastic wrap,

and ensuring the area is draft free may help.

In winter, your dough will take longer to rise.

Notes

The Sunbeam

5 Year Motor

Guarantee

Sunbeam has built its reputation

on manufacturing quality electrical

appliances. Our Cafe Series

Coffee

Grinders (EM0480, EM0490) are

constructed from the highest quality

materials. So much so, we guarantee our

Coffee Grinders' motors for ﬁve (5) years

against faulty materials or manufacture.

This guarantee is just another expression

of our conﬁdence in the way we make

appliances at Sunbeam. In order to be

eligible for this guarantee, you must retain

your receipt as proof of purchase.

Your Planetary Mixmaster

Power Drive

Bench Mixer is covered for the ﬁrst year

against faulty material or manufacture

by the Sunbeam 12 Month Replacement

Guarantee. Should you experience any

difﬁculties with your appliance within

this 12 Month period, please phone our

customer service line for advice on 1300

881 861 in Australia, or 0800 786 232 in

New Zealand.

The Sunbeam (5) ﬁve year motor guarantee

begins from date of purchase and extends

for four years beyond the 12 Month

Replacement Guarantee. It covers only

the motor, guaranteeing it against faulty

materials or manufacture. It does not cover

damage caused by accident, misuse or

being used in a manner not in accordance

with the Instruction Book. Similarly, this

motor guarantee does not cover freight or

any other costs incurred in making a claim.

If a fault should develop with the motor

after the period covered by the 12 Month

Replacement Guarantee, please call

Sunbeam Customer Service on the number

listed below or send a written claim to

Sunbeam at the address listed below.

On receipt of your claim, Sunbeam will

advise you on how to obtain a replacement

motor if your motor is defective.

Alternatively, you can return the Planetary

Mixmaster

Power Drive Bench Mixer

to any of Sunbeam’s authorised service

centres, together with your receipt. The

service centre will examine the motor and

if it is faulty or defective, the motor will be

replaced free of charge.

For a complete list of Sunbeam’s authorised

service centres visit our website or call:

Sunbeam Corporation Ltd.

Australia

www.sunbeam.com.au

1300 881 861

Units 5 & 6, 13 Lord Street

Botany NSW 2019 Australia

Sunbeam Corporation Ltd.

New Zealand

www.sunbeam.co.nz

0800 786 232

Level 6, Building 5, Central Park

660-670 Great South Road

Greenlane, Auckland

The beneﬁts given to you by this guarantee

are in addition to your other rights and

remedies under any laws which relate to

the appliance.

Our goods come with guarantees that

cannot be excluded under the Australian

Consumer Law and under the New Zealand

Consumer Guarantees Act. In Australia you

are entitled to a replacement or refund for

a major failure and for compensation for

any other reasonably foreseeable loss or

damage. You are also entitled to have the

goods repaired or replaced if the goods fail

to be of acceptable quality and the failure

does not amount to a major failure.

IMPORTANT NOTE

Sunbeam agrees to replace the motor in

the event of the motor developing a fault or

defect, within the four years after the

12 Month Replacement Guarantee.

As your Planetary Mixmaster

Power Drive

Bench Mixer needs to be assessed at a

Sunbeam authorised service centre, it will

not be accepted through retail stores.

If using the Planetary Mixmaster

Power

Drive Bench Mixer for commercial use this

motor guarantee is limited to 12 months

from the date of purchase.

This Sunbeam product is covered by a 12 month replacement or repair

warranty, which is in addition to your rights under the Australian Consumer

Law (if your product was purchased in Australia) or New Zealand Consumer

Guarantees Act (if your product was purchased in New Zealand).

12 Month Warranty

Should you experience any difficulties with your product

during the warranty period, please contact our customer

service line for advice on 1300 881 861 in Australia,

or 0800 786 232 in New Zealand.

Alternatively, you can send a written claim to Sunbeam

to:

Australia

Units 5 & 6, 13 Lord Street

Botany NSW 2019 Australia

New Zealand

Level 6, Building 5, Central Park

660-670 Great South Road

Greenlane, Auckland

Upon receipt of your claim, Sunbeam will seek to

resolve your difficulties or, if the product is defective,

advise you on how to obtain a replacement or refund.

To assist us in managing warranty claims, we

recommend you register your product as soon as

practicable after purchase by creating a MySunbeam

account on our website and send a copy of your original

receipt to Sunbeam.

In order to make a claim under our warranty, you must

have the original proof of purchase documentation for

the product and present it when requested .

Should your product develop any defect within

12 months of purchase because of faulty materials

or workmanship, we will replace or repair it, at our

discretion, free of charge. A product presented for repair

may be replaced by a refurbished product

of the same type rather than being repaired.

Refurbished parts may be used to repair the product.

Our replacement or repair warranty only applies

where a defect arises as a result of faulty material

or workmanship during the warranty period. Your

warranty does not cover misuse or negligent handling

(including damage caused by failing to use the product

in accordance with this instruction booklet), accidental

damage, or normal wear and tear.

Your warranty does not:

• cover freight or any other costs incurred in making a

claim, consumable items, accessories that by their

nature and limited lifespan require periodic renewal

(such as filters and seals) or any consequential loss

or damage; or

• cover damage caused by:

- power surges, power dips, voltage supply problems,

or use of the product on incorrect voltage;

- servicing or modification of the product other than by

Sunbeam or an authorised Sunbeam service centre;

- use of the product with other accessories,

attachments, product supplies, parts or devices

that do not conform to Sunbeam specifications; or

- exposure of the product to abnormally corrosive

conditions; or

• extend beyond 3 months if the product is used

in commercial, industrial, educational or rental

applications.

The benefits given to you by our warranty are in addition

to other rights and remedies under law in relation to the

product.

In Australia our goods come with guarantees that cannot

be excluded under the Australian Consumer Law. You are

entitled to a replacement or refund for a major failure

and for compensation for any other foreseeable loss or

damage. You are also entitled to have the goods repaired

or replaced if the goods fail to be of acceptable quality and

the failure does not amount to a major failure.

Our goods also come with guarantees that cannot be

excluded under the New Zealand Consumer Guarantees Act.

If your warranty claim is not accepted, we will inform

you and if requested to do so by you, repair the product

provided you pay the usual charges for such repair. You

will also be responsible for all freight and other costs.

Should your product require repair or service after

the warranty period, contact your nearest Sunbeam

service centre. For a complete list of Sunbeam’s service

centres, visit our website or call our customer service

line for advice on 1300 881 861 in Australia,

or 0800 786 232 in New Zealand.

is a registered trademark.

12/08

is a registered trademark.

Need help with your appliance?

Contact our customer service team or visit

our website for information and tips on

getting the most from your appliance.

In Australia

Visit www.sunbeam.com.au

Or call 1300 881 861

In New Zealand

Visit www.sunbeam.co.nz

Or call 0800 786 232

‘Mixmaster’ is a registered trademark of Sunbeam

Corporation.

‘Scapemaster’ is a trademark of Sunbeam Corporation.

Made in China. Designed and engineered in Australia.

Due to minor changes in design or otherwise, the product

may differ from the one shown in this leaflet.

ABN 45 000 006 771

Units 5 & 6, 13 Lord Street

Botany NSW 2019 Australia

Level 6, Building 5, Central Park

660-670 Great South Road

Greenlane, Auckland

New Zealand

Sunbeam Corporation Pty Ltd, Acn 000 006 771

GCDS-SUN46158-SL

1/14

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Sunbeam MX9600Z Zumbo Limited Edition Mixmaster in the language / languages: English as an attachment in your email.

The manual is 2,21 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Sunbeam MX9600Z Zumbo Limited Edition Mixmaster Manual

Product: