651825

Sub-Zero UC15 Manual

5
Zoom out
Zoom in
Previous page
1/44
Next page
subzero.com
|
5
CUBE WEIGHT
Cube weight increases or decreases depending on the
amount of dimple, or depression in the octagonal-shaped
ice cube. Cube weight can be adjusted by increasing the
freeze time.
To adjust cube weight:
1 Touch and hold ‘POWER’.
2 Touch and release ‘CLEAN’ once to add one minute of
freeze time. Inspect the cubes after several production
cycles and repeat if a heavier cube is desired. Up to ve
minutes of additional freeze time can be added.
3 Touch ‘CLEAN’ six times to reset freeze time to the
factory setting.
ICE LEVEL
A thermostat in the ice storage bin signals ice production to
stop when the bin is full. If ice production stops before the
bin is full or continues after the bin is full, the ice level can
be adjusted. The thermostat control is located behind the
kickplate. Refer to the illustration below.
To adjust ice level:
1 Remove the kickplate to access the thermostat control.
2 Turn the control to the left to decrease the level of ice or
to the right to increase the level.
Operation
PRIOR TO USE
Clean the ice machine thoroughly with warm water and mild
detergent. Rinse and dry with a soft cloth to remove any
residual oil and grease left from the manufacturing process.
Refer to care recommendations on page 6.
All surfaces that come in contact with the water system
should be cleaned and sanitized prior to use. Refer to the
cleaning and sanitizing procedure on page 7. Use only the
cleaner and sanitizer made for the Sub-Zero ice machine.
Ice machine cleaner and sanitizer can be ordered online at
subzerowolfstore.com. For questions, contact Sub-Zero
customer care at 800-222-7820.
ICE PRODUCTION CYCLE
Depending on ambient conditions and water temperature,
one ice production cycle takes approximately 30 minutes.
1 Water ll cycle. The water inlet valve purges old water
from the system.
2 Refrigeration system start-up. The compressor starts
after the water ll cycle and remains on throughout the
freeze and harvest cycles. The condenser fan motor
starts and runs throughout the freeze cycle.
3 Freeze cycle. Water is sprayed into the inverted cups.
The water freezes layer by layer until an ice cube forms
in each cup. The control system adjusts the length of the
freeze cycle to conditions.
4 Harvest cycle. The evaporator warms, allowing the
cubes to be released and drop into the storage bin. The
control system adjusts the length of the harvest cycle
to conditions. At the end of the harvest cycle, another
freeze cycle begins.
5 Automatic shut-off. The level of ice in the storage bin
controls the automatic shut-off. When the bin is full, ice
will contact the bin thermostat, which cools, signaling ice
production to stop. When the ice level drops and ice no
longer contacts the bin thermostat, it will warm, signaling
ice production to resume.
OPERATION
THERMOSTAT
CONTROL
Ice level adjustment.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sub-Zero UC15 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sub-Zero UC15 in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 3,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info