611083

Stuv 16-78 Manual

21
Zoom out
Zoom in
Previous page
1/59
Next page
S16-IME-6L
12-07
40
S16-IME-6L
12-07
41
- Dégager les ouvertures pour le
passage des gaines de convection (Ø
150 mm) [photo 1].
Attention : si vous avez choisi cette
option, la gaine d’adduction d’air
extérieur pour la combustion (Ø
63 mm) doit aussi traverser le caisson
de ventilation [photo 2]. Passage
dans le caisson : idéalement par
le dessous ou par la gauche car le
circuit électronique d’alimentation du
ventilateur occupera la partie droite ;
si elle doit passer par la droite, le
circuit électronique devra être monté
à gauche.
- Mettre à niveau en réglant la hauteur
des pieds [photo 3].
- Fixer le caisson au sol [photo 4].
- Monter les collerettes [photo 5], fixer
la gaine au moyen d’un collier de
serrage.
- Introduire (s’il y a lieu) la gaine
d’adduction d’air extérieur [photo 6].
- Introduire au travers du passe-câble
[photo 7] :
- le câble d’alimentation (2 conduc-
teurs + terre) ; cette ligne doit être
protégée par un fusible bipolaire,
- le câble de commande du sélecteur
à 4 conducteurs.
- Déposer le plateau sur le caisson de
ventilation et assembler par vis [photo
8].
Le caisson de ventilation est suspendu
au plateau de prépose
Procéder de la même manière en ce qui
concerne le raccordement des gaines et le
passage de la gaine d’air de combustion.
3 4 5
7 8
1 2
6
- Maak de openingen vrij voor de
doorgang van de luchtroosters
(Ø 150 mm) [foto 1].
Opgelet : indien u deze optie hebt
gekozen, moet de toevoerkoker van
buitenlucht voor de verbranding
(Ø 63 mm) ook door de ventilatiekast
lopen [foto 2]. Doorgang door de
ventilatiekast : ideaal via de onderkant
of de linkerkant, aangezien het
elektronisch voedingscircuit van de
ventilator zich rechts zal bevinden ;
indien de koker via de rechterkant
doorgang moet vinden, zal het
elektronisch circuit links moeten
worden gemonteerd.
- Waterpas zetten door de hoogte van
de voeten te regelen [foto 3].
- Bevestig de ventilatiekast op de
bodem [foto 4].
- Monteer de kragen [foto 5], bevestig
de koker door middel van een buis-
klem.
- Breng (indien dit het geval is) de
toevoerkoker van buitenlucht aan
[foto 6].
- Aan te brengen doorheen de
kabeldoorgang [foto 7] :
- de voedingskabel (2 geleiders +
aarding); deze verbinding moet
worden beschermd door een
tweepolige zekering,
- - de bedieningskabel van de regelaar
met 4 geleiders [photo 8].
De ventilatiekast wordt aan de bodem-
plaat opgehangen
Ga op dezelfde manier te werk wat
betreft de aansluiting van de kokers
en de doorgang van de koker voor de
verbrandingslucht.
- Liberare le aperture per il passaggio
dei condotti di convezione (Ø 150
mm) [foto 1].
Attenzione : se è stata scelta questa
soluzione, il condotto di derivazione
d’aria esterna per la combustione
(Ø 63 mm) deve passare attraverso il
cassone di ventilazione [foto 2].
Attraversamento del cassone :
idealmente dal di sotto o a sinistra
poiché il circuito elettronico di
ventilazione occuperà il lato destro ;
se deve passare a destra, il circuito
elettronico dovrà essere installato a
sinistra.
- Livellare regolando l’altezza dei piedi
[foto 3].
- Fissare il cassone al suolo [foto 4].
- Montare le flange [foto 5]; fissare il
condotto per mezzo di un anello di
serraggio.
- Introdurre all’occorrenza il condotto di
derivazione d’aria esterna [foto 6].
- Introdurre attraverso la boccola
[foto 7] :
- il cavo di alimentazione (2
conduttori + presa di terra) ;
questo circuito deve essere protetto
con un fusibile bipolare,
- il cavo di comando del selettore a 4
conduttori.
- Sistemare la piastra sul cassone di
ventilazione e assemblare con le viti
[foto 8].
Il cassone di ventilazione è appeso alla
piastra di pre-posa
Procedere allo stesso modo per quanto
concerne il collegamento dei condotti
e il passaggio del condotto d’aria di
combustione.
de los conductos de convección (Ø
150 mm) [foto 1].
Atención : si ha elegido esta opción,
el conducto de toma de aire exterior
para la combustión (Ø 63 mm)
debe atravesar también el cajón de
ventilación [foto 2].
Paso al interior del cajón : idealmente
por la parte inferior o izquierda
ya que el circuito electrónico de
alimentación del ventilador ocupará
la parte derecha; si debe pasar por la
derecha, el circuito electrónico deberá
montarse a la izquierda.
- Nivele regulando la altura de los pies
[foto 3].
- Fije el cajón al suelo [foto 4].
- Monte los collarines [foto 5] ; fije
el conducto por medio de una
abrazadera de apriete.
- Introduzca (si procede) el conducto de
toma de aire exterior [foto 6].
- Introduzca, a través del paso de
cables [foto 7]:
- el cable de alimentación (2
conductores + tierra) ; esta línea
debe estar protegida por un fusible
bipolar,
- el cable de mando del selector de 4
conductores.
- Deposite la bandeja sobre el cajón de
ventilación y atorníllela [foto 8].
El cajón de ventilación está suspen-
dido de la placa de soporte
Proceda de la misma forma en lo que
respecta a la unión de los conductos
y el paso del conducto del aire de
combustión.
- Abra as entradas para as condutas
de convecção (150 mm de diâmetro)
[fotografia 1].
Atenção : se tiver escolhido esta
opção, a conduta de entrada de ar do
exterior para a combustão (63 mm de
diâmetro) deverá atravessar a caixa
de ventilação [fotografia 2]. Passagem
através da caixa : o ideal seria passar
por baixo ou pela esquerda, dado o
circuito electrónico de alimentação do
ventilador ocupar a parte direita ;
se tiver de passar pela direita, o circuito
electrónico deverá então ser instalado
do à esquerda.
- Regule a altura dos pés para nivelar a
caixa [fotografia 3].
- Fixe a caixa ao chão [fotografia 4].
- Monte os rebordos [fotografia 5], fixe
a conduta com uma braçadeira de
aperto.
- Introduza (se for necessário) a
conduta de adução de ar exterior
[fotografia 6].
- Introduza pela abertura de passagem
dos cabos [foto 7] :
- o cabo de alimentação (2 condu-
tores + fio de terra) ; esta linha deve
estar protegida com um fusível
bipolar,
- o cabo de comando do selector de 4
condutores.
- Coloque o tabuleiro na caixa de
ventilação e una com parafusos
[fotografia 8].
A caixa de ventilação está suspensa na
placa de suporte
Proceda da mesma maneira para ligar as
condutas e para a passagem da conduta
de ar de combustão.
- Free the openings for the convection
ducts (Ø 150mm) [pic. 1].
Caution : where this is the selected
option, the outside combustion
air duct (Ø 63 mm) must also run
through the ventilation box [pic. 2]
Passage through the box : ideally from
the bottom or from the left hand
side since the electronic power circuit
will occupy the right hand side ; if for
some reason it has to be on the right
hand side, then the electronic circuitry
will have to be fitted to the left.
- Set level with the adjustable legs
[pic. 3].
- Secure the box to the floor [pic. 4].
- Install the flanges [pic. 5], secure duct
with a clamp
- Insert (when applicable) the outside
air inlet duct [pic. 6].
- Insert through the cable guide
[pic. 7] :
- the power supply cable (2
conductors + earth); this line must be
protected by a two-pole fuse,
- the 4-conductors selector control
cable.
- Place the plate on the ventilation
chamber and screw into place
[photo 8].
The ventilation box is suspended from
the pre-fitting plate
Proceed in the same way concerning the
connection of ducts and the passage of
the combustion air duct.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stuv 16-78 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stuv 16-78 in the language / languages: English, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 3,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info