750860
9
Zoom out
Zoom in
Previous page
1/25
Next page
WARNING: The batteries should not be recharged, disassembled, electrically short-
circuited, be mixed or used with other types of batteries. If rechargeable
accumulators instead of batteries are going to be used, we recommend
using (e.g. NiMH) types with low self-discharge to ensure long time
operation of remote control.
1.5 Usage of external USB devices
It is recommended to use USB 2.0 storage devices. If your device is not compatible to USB 2.0
specifications, the playback with your receiver might not work properly.
If you are going to use external USB HDD (Hard Disk Drive) please consider that the power
specifications might exceed the supported output of your receiver (5 V/500 mA). If so, please
connect your USB HDD to an according external power adapter.
STRONG cannot guarantee compatibility with all types of USB storage devices.
It is advised not to store important information on USB storage devices used with the receiver.
Always make backups of data on your USB storage device before using it with this receiver.
STRONG will not take responsibility for any loss of information or circumstances caused by loss of
information.
Please ensure that either the USB device is already formatted to NTFS or FAT32 or format the USB
device via your receiver. Formatting requires entering the PIN code (default 1234)
STRONG cannot guarantee the playback of all files although extensions are listed, as it depends on
file size, codec, bit rate and resolution.
2.0 YOUR RECEIVER
2.1 PIN-CODE DEFAULT: 1234
2.2 Front Panel
Fig.1
1. Mode indicator: RED indicates that the receiver is in STAND-BY mode.
GREEN indicates that the receiver is in OPERATING mode.
2. IR sensor: Point your remote control towards this sensor.
3. USB: Connector for USB devices.
2.3 Rear Panel
Fig.2
1. RF IN To connect to your antenna for the reception of broadcast signal.
2. S/PDIF Coaxial To connect your receiver to a digital audio amplifier.
3. HDMI To connect your receiver with your TV set using a HDMI cable.
4. LAN To connect your receiver to Ethernet LAN
5. TV SCART To connect your receiver with your TV set using a SCART cable.
6. Power Cord Your receiver requires a voltage of 220~240 V AC (Auto-
selectable), 50/60 Hz +/-5%. Check the local power specification
before connecting your receiver to the wall outlet.
5
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strong SRT8209 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strong SRT8209 in the language / languages: English as an attachment in your email.

The manual is 0,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Strong SRT8209

Strong SRT8209 User Manual - French - 27 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info