424993
12
Zoom out
Zoom in
Previous page
1/31
Next page
PART 1 • English
11
English
Note: Please, make sure that your receiver is connected by SCART or 3 RCA cable (Video,
Audio L/R) to your TV set when you connect your VCR (or DVD) to receiver. You will not
get video signal from your VCR (DVD) through the receiver if your receiver is connected
only by HDMI or YPbPr connector to your TV set.
3.4 Download new software
This receiver can download new system software by OTA update from satellite and is also able to load new
software via USB from external storage device or PC. Therefore software updates via RS-232 port is only a
“stopgap”. To upload new software, connect the receiver with an USB cable to an external storage device.
Instructions how to download software can be found on our website www.strong.tv (support > download).
3.5 Connecting to external USB Hard disk
Switch on your external HDD (connect the power adapter if applicable) before you connect the USB
connector at the back of your receiver. After finishing the First Installation (Cap. 4.0) proceed with
following steps:
1. Unless the USB-Hard disk is already formatted in FAT32 and recognised successfully for the first
time you will get a message to format your device to FAT32 inApplication >USB menu.
2. In this menu press the YELLOW (Format) button on your remote control to confirm.
After ~10 to 20 sec. (depends on HDD size) formatting will be finished and you can leave the
menu with the MENU or EXIT button.
3. Go to “Application” >”PDR” menu to adjust the preferred recording duration and set
Timeshift to OFF or ON as desired.
IMPORTANT: During formatting all data on the hard disk will be deleted and get permanently
lost. STRONG cannot be granted for any loss or damage of data, if you format the
hard disk.
4.0 STARTING UP FOR THE FIRST TIME
Ensure that your receiver is correctly connected to your television, satellite and terrestrial antennas. Make sure
that satellite and terrestrial signals are of good quality. Ask your local Strong dealer to check your installation or
satellite signal if you are not sure how to do this.
Confirm that the power plug of receiver is plugged into the wall outlet. Turn on the receiver by power switch on
rear panel.
The language section menu will be showing on your TV Screen.
It is recommended that you do first time installation following Installation Wizard step by step.
It will help you easily achieve system configuration and channel installation. If you are advanced user then you
can skip wizard by pressing EXIT button and set-up channels using Installation menu.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strong srt 8345 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strong srt 8345 in the language / languages: English as an attachment in your email.

The manual is 1,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Strong srt 8345

Strong srt 8345 User Manual - German - 35 pages

Strong srt 8345 User Manual - French - 33 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info