480533
14
Zoom out
Zoom in
Previous page
1/15
Next page
PART 1 • English
11
English
5.7.4 Record configure
Record Device
If you have multiple partitions on your storage device – select one of them as default partition for recording.
Format
If you would like to format storage device or partition on itselect partition and file system to be used. Move focus to Format
and press OK. You will need to confirm format by pressing OK button one more time. Format procedure will take some time,
depends from size of storage device used. At the end of process “Format is complete” message will appear.
Warning: Format functions will delete all records, data and information from your USB device. STRONG will
not take any responsibility for damaged or lost data on the USB device.
6.0 RECORDING FUNCTION
To perform a recording you have to insert USB storage device into USB port of the receiver. Select a channel you would
like to record and press REC button. The recording will start and at let upper corner of the screen you will see recording
notification with blinking red dot and record duration.
During a recording you can’t change a channel to another one.
You can check details of the recording in progress by pressing to INFO button.
To stop a recording press STOP button on remote control.
Another way of doing recording is use Scheduler – please refer to 5.4.1 Schedule of this manual.
Average record size (values are approximately, depend from bit rate of actual broadcast):
MPEG2 SD channel – 1 hour take about 2.2 GB space
MPEG4 SD channel – 1 hour take about 1 GB space
MPEG4 HD channel – 1 hour take about 4.5 GB space
Accessing to the recordings. You can access recordings by pressing button LIST on remote control. Also list of recordings can
be accessed through Menu USB Multimedia Records. Please, refer to 5.7.1 Multimedia for details of available functions.
A.1 TROUBLESHOOTING
There may be various reasons for the abnormal operation of the receiver. Check the receiver according to the procedures
shown below. If the receiver does not work properly after checking it, please contact the dealer or the local Service
Hotline. Do NOT open the receiver cover. It may cause a dangerous situation and the warranty will get void.
Problem Possible cause What to do
Stand-by indicator do not
light up
Mains lead unplugged/multipoint
connector switched off
Front panel switch is in OFF position
Check mains lead /switch multipoint
connector on
Set front panel switch to ON position
No signal found Aerial is disconnected
Aerial is damaged/misaligned
Out of digital signal area
Active antenna requires to switch ON
antenna power/external feed
Check aerial lead
Check aerial
Check with dealer
Switch receiver’s Antenna Power ON/
connect external feed
No picture or sound on TV Input is not selected on your TV
TV or VCR are not connected to main
Bad cable connection
Switch to correct TV input
Check mains lead
Firmly plug in cables between receiver and TV
Scrambled channel message Channel is scrambled Select alternative channel
No response to remote
control
Receiver off
Handset not aimed correctly
IR sensor obstructed
Hand set batteries exhausted
Plug in and turn on plug
Aim handset at IR sensor
Check for obstructions
Replace handset batteries
Forgotten channel lock code Contact local Service Hotline or send email to
our Support via www.strong.tv
Forgotten menu lock code Contact local Service Hotline or send email to
our Support via www.strong.tv
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strong SRT 8110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strong SRT 8110 in the language / languages: English as an attachment in your email.

The manual is 1,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info