480571
13
Zoom out
Zoom in
Previous page
1/25
Next page
10
PART 2 • English
7.1 Channel Setup
The installation menu allows you to change satellite settings and to search for channels. It consists of
the following sub-menus: Channel Scan and Channel Editor. Choose the desired sub menu with pq and
press OK to advance.
7.1.1 Channel Scan
Use this menu to select the satellite, change the settings for the used antenna and start scan process for
searching the channels.
Satellite: Use pq to highlight Satellite and tu to select the satellite you wish to
change the settings for. To display the list of all available satellites, press OK. At
the end of this list you can find Newsat1 -10. Those can be used to configure a
new satellite setup.
LNB: Select LNB type if you are using another LNB as Univ.LNB model. As this is the
common used LNB, it is set per default.
DiSEqC: If you are using a DiSEqC switch in order to connect more dishes, select the
correct used switch type. Select DiSEqC 1.0 for maximum 4 dishes. DiSEqC 1.1
for maximum 16 dishes and select None if you don’t use any switch.
DiSEqC Port: If you are using a DiSEqC switch you need to set the correct DiSEqC port which
belongs to the connected satellite.
Transponder: Select this option, if you want to scan manually or check the signal on the
desired transponder frequency. Use tu to select the transponder of you
choice, or open the Transponder list of the selected satellite with OK.
Motor Control: If you are using a DiSEqC motor to install multiple satellites. Select the
according setup type withtu. Select DiSEqC 1.2 for manual setup of each
satellite or select GOTO-X for automatic calculation after you have adjusted the
0-position and corresponding Cartesian coordinates of your location.
Note: Please consider that GOTO X must be supported from your Motor as well!
Motor Setting: Here you can setup the necessary settings according to the used Motor
Control. Adjust and store these settings correctly, in order to be able to proceed
with Search Start.
Search Start:
Before you start the scan process please make sure that all settings are made correctly and Strength and
Quality bars are showing green colours. If the Strength and Quality bars showing red or yellow colours,
then the satellite signal is too weak. Please try to adjust your satellite dish first, to improve the signal.
At the first time installation there was performed the HD+ Channel Scan from APS. After this successful
scan process you can choose following of the additional possibilities:
Select Search Start and press OK.
A new menu will be opened on the right side of your screen, called “Options”. Use this menu to perform
an Automatic, TP (manual) or Network channel search on one or more satellites. Use tu pq to
highlight and OK to select an option.
Start Auto Scan: Use this option to perform a full channel scan on the selected satellite, under
the below mentioned conditions.
TP Search Start: Use this option to perform a scan on the selected transponder only.
Network Search Start: Use this option to receive new launched channels from the selected satellite.
The receiver will perform an additional search for channels from the NIT table
(NIT= Network Identification Table).
Search Mode: Select All to scan all channels including scrambled channels or FTA to scan for
Free-To-Air channels only.
NIT Search: Select OFF if you don’t want to perform a network search or set ON to perform
a network search.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strong SRT 7805 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strong SRT 7805 in the language / languages: English as an attachment in your email.

The manual is 1,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info