751652
23
Zoom out
Zoom in
Previous page
1/32
Next page
Auto Standby: This function is a new power saving feature that helps reducing power
consumption. It switches the receiver to standby when no command has
been received from the remote control for at least the set time. Possible
settings are: 1H- 6H and OFF to deactivate.
S/PDIF Audio Output: Toggles between PCM and RAW (Bitstream) output. When PCM is selected, all
digital audio will be converted to stereo audio. RAW enables you to listen or
transfer Dolby® Digital/Dolby® audio to a home cinema set through coaxial S/
PDIF. (Not Dolby® Digital Plus)
HDMI Audio Output: Toggles between PCM and RAW (Bitstream) output. When PCM is selected, all
digital audio will be converted to stereo audio. RAW enables you to listen or
transfer Dolby® Digital/Dolby® Digital Plus* audio to the TV via HDMI or to a
home cinema set.
Standby After Record: This function allows you to determine whether the receiver should switch to
standby after the end of the programmed timer(s) On, or whether the receiver
should remain switched on O.
Program List Display: Choose between Advanced for program list with3rows with 47 channels or
Simple Programme list with 1 row with 10 channels and sort functions.
OTA In standby Active: Select a time after the receiver went to standby mode, to check if there is new
software available on air.
Dolby Audio First Set to On if you would like to choose Dolby audio only if available on a
channel.
Press to leave the System Settings menu.
7.3.2 Display
In this submenu Display Settings you can setup which screen type you have connected and how the best
way it is shown. The following parameters can you adjust:
Resolution 576i, 576p, 720p, 1080i or 1080p, to adjust the optimum resolution your TV set
supports.
Aspect Ratio Auto, 16:9 or 4:3, depending on the type of your TV screen.
Aspect Conversion Pan Scan, Letterbox, Pillar Box or Full Screen, to choose the preferred picture
format.
Transparency Make the live TV video visible below the menu and information banner.
Banner Time Select the time-out of the information banner.
CEC Select On if you would like to share basic remote control functions like
Standby and Volume over the HDMI CEC control.
These remote commands are send over the HDMI cable to the connected
device.
7.3.3 Lock
This menu enables you to dene and edit your PIN code, set Installation or Menu Lock. Choose a setting
with pq and press OK to list the possibilities or use tu to change the value of the highlighted setting.
Use the 0~9 buttons to access this menu options below. Enter the (Default PIN: 0000) if you have not
changed it.
Menu Lock Select ON or OFF. Menu Lock allows you to lock the access to menus.
Immediately if you press menu a PIN request banner will pop-up.
19
English
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strong SRT 7502 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strong SRT 7502 in the language / languages: English as an attachment in your email.

The manual is 0,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info