751651
12
Zoom out
Zoom in
Previous page
1/30
Next page
4.0 STARTING UP FOR THE FIRST TIME
Ensure that your satellite signal is of good quality and that all connections are properly setup. In case of
difficulties or questions, please ask your local dealer or service hotline for assistance. It is recommended
to follow the First Time Installation step by step. It will guide you through the basic installation and setup
process. You can enjoy digital HD broadcasts within just a few minutes. To enjoy the complete range of
channels and to watch your preferred scrambled services, it is recommended to insert the ORF Digital
smartcard. Then continue with the first time installation. Please pay attention to the correct insertion of
the smartcard.
4.1 Language and Video Settings
After connecting your receiver for the first time, the OSD Language, Aspect Ratio, Aspect Conversion and
HDMI Resolution menus will be shown. Change your language with t u and use pq to select the other
settings. For these settings, you can also use OK to show a list of available settings. Adjust the Aspect
Ratio according to your TV (4:3 for an analogue CTV set and 16:9 for your new flat screen/HD TV) and
select the Conversion of your preference.
For HDMI Resolution the default setting 720p is recommended, but many TVs already support higher
resolutions. Therefore you can choose Auto (it will check the highest resolution supported by the TV) or
1080i. 1080p will only be supported after a future software update.
NOTE: If you select an HDMI resolution which your TV does not support, the
receiver will switch to the previous setting automatically after ~10 sec. If you
can see the displayed message, please confirm the selected resolution by
pressing OK.
During any stage of the First Time Installation, you can press BLUE Next to go to the next step or YELLOW
Previous to get back to the previous step.
4.2 Antenna Setup
This receiver is already adjusted for reception of Astra 19.2 satellite with the correct settings as it is
most common. Per default it is setup for DiSEqC port 1, but you can use the setting as well if you are
not connected to any switch. You only need to change these settings if you are not connected to Astra
19.2 or you don't have this satellite connected to port 1 of your DiSEqC switch. To adjust your antenna
settings for the Satellite, LNB Power, LNB Type, LNB Freq, DiSEqC 1.0 and Transponder correctly, use the
t u and pq buttons.
For the better convenience and if you have a multi dish installation, we support the Auto DiSEqC Scan*
function, which can be activated by pressing the GREEN button.
For further details and information about the settings, see chapter 7.1.1 Antenna Setup
Within the First Time Installation it is only possible to adjust settings for up to 4 satellite positions. In
order to proceed with First Time Installation, use BLUE Next to go forwards.
* This new function can recognise available satellites in the persisting antenna installation. The predefined satellites are: Astra 19.2E, Astra
23.5E, Astra 28.2E, HotBird 13.0E and Eutelsat 9.0E.
4.3 Channel list selection
In this menu you can highlight the channel list of your choice by pressing t u and then choose the
appropriate option in below.
8
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strong SRT 7501 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strong SRT 7501 in the language / languages: English as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Strong SRT 7501

Strong SRT 7501 User Manual - German - 35 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info