480572
16
Zoom out
Zoom in
Previous page
1/20
Next page
13
PART 2 • English
English
6.3.2 Audio Mode and Language
Press A.FORMAT button in viewing mode. Further pressing will change audio channel between Left, Right and Stereo.
Press the LANG button to select one of the available audio languages.
6.3.3 Video Format
Press the V.FORMAT button in viewing mode. Further pressing will change the HDMI resolution. You will only see
differences if you are connected via HDMI.
6.3.4 Teletext
Press TXT button in viewing mode. If teletext is available in several languages, select a language from the list.
6.3.5 Subtitles
Press SUBT button in channel view mode. The list of available subtitle languages will be displayed. Use pq to select a
language and confirm with OK. To disable subtitles press SUBT button once more.
6.3.6 Special buttons
Use below buttons in viewing mode to perform desired actions.
DIGIAKTIF: Shows technical information of the current channel and might help to resolve channel
related issues.
MODE: Gives you direct access to GAMES menu.
MEDIA: Gives you direct access to the Media Browser in case a USB device has been connected.
P<P: Switches between the last two watched channels.
TIMERS: Gives you direct access to the TIMERS menu.
PAUSE: Will give you access to the ZOOM menu. Use the buttons described within to perform the
different zoom actions.
A.1 TROUBLESHOOTING
There may be various reasons for the abnormal operation of the receiver. Check the receiver according to the procedures
shown below. If the receiver does not work properly after checking it, please contact the dealer. Do NOT open the
receiver cover. This may cause a dangerous situation and will void the warranty.
Symptom Cause Remedy
The display on front
panel does not light up.
The power cord is not plugged in. Check if the power cord is plugged in to the wall
outlet.
No picture or sound Wrong connection of the Audio/Video
output of the receiver to TV or Amplifier.
Connect the Audio/Video output of the receiver to
TV/Amplifier correct.
Audio muted. Press the MUTE button.
TV powered off. Turn TV on.
No picture The receiver can’t receive the signal. Check the antenna cable, replace the cable, or
connect the cable to the receiver tightly.
Incorrect values of some tuner
parameters.
Set the values of tuner parameters correctly in
installation menu or check channel parameters
with values from kingofsat.net or Lyngsat.com
Wrong direction of the dish. Check the signal strength with a spectrum analyzer
and adjust your dish correctly.
HDMI connection not detected/
established correctly.
Please switch ON the receiver firstly and switch ON
TV set afterwards. It might happen that there are
observed interruptions on HDMI due cable quality
not sufficient, in such cases we can recommend a
HDMI amplifier or better quality cable.
Irdeto Message E30-4 Validation in progress It can take up to 7 min. until card validation
process is finished. Please do not power off the
receiver or remove the smartcard during this time.
The remote control does
not work
The batteries of the remote control are
not inserted or exhausted
Check whether the batteries are inserted correctly
in your remote control. Check the batteries, and
if exhausted replace the batteries in the remote
control.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strong SRT 7500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strong SRT 7500 in the language / languages: English as an attachment in your email.

The manual is 1,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info