480573
13
Zoom out
Zoom in
Previous page
1/23
Next page
10
PART 1 • English
Transponder and tu to set the desired transponder. Signal bars indicating signal quality and strength
can be found on the bottom of the screen. These bars show the signal conditions for the chosen satellite
and transponder. You can now adjust the following settings: LNB type, LO Frequency, LNB power, Band
(22 kHz), Switch Type, Switch Input, Dish Mode and Dish Position. Once all settings are made, press EXIT
to get to the previous menu or use pq to highlight Go To and tu to select Auto Scan or Manual Scan
to advance to Auto Scan or Manual Scan.
A confirmation banner will now be displayed. Press OK to confirm the made changes or EXIT to discard.
7.1.2 Auto Scan
Use this menu to perform an automatic channel search on one or more satellites.
On the left of the screen, a list with satellites is displayed. Use pq to highlight the satellite(s) you wish
to scan and press OK to mark the highlighted satellite. Press OK again to unmark a marked satellite.
Note: you can mark multiple satellites. Auto Scan will search all marked satellites for
available channels.
Now select the desired scanning options on the right of the screen. Use u pq to highlight and OK to
set an option.
Scan Mode All: scan all channels
Free: scan Free-To-Air channels only
Scrambled: scan scrambled channels only.
Service Type All: scan TV and Radio channels
TV scan: TV channels only
Radio: scan radio channels only.
Network Search Disabled: no network search
Enabled: network search will be performed.
Once all settings are made, press the GREEN button on the remote control to start the scan or EXIT to
quit without scanning. All newly found channels will be stored at the end of the channel list.
Tip: Network Search: If Disabled is selected, the receiver will search only for
channels available from the preset transponder list of the selected satellite. If
it is set to Enabled, the receiver will perform an additional search for channels
from the NIT table (NIT= Network Identification Table). Use this option to
receive new launched channels from the selected satellite.
7.1.3 Manual Scan
Use this menu to scan a single transponder only.
The following can be set: Satellite, Transponder, Frequency, Polarisation, Symbolrate, Scan Mode, Service
Type and Network search. Use pq to move the highlight to the chosen setting and tu to change its
value. Once all settings set correct, press the GREEN button to start scanning or EXIT to quit. All newly
found channels will be stored at the end of the channel list.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strong SRT 7100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strong SRT 7100 in the language / languages: English as an attachment in your email.

The manual is 1,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info