751646
21
Zoom out
Zoom in
Previous page
1/32
Next page
17
If your dish is physically obstructed to the East or West (example by a wall), you can limit its moving
range by pressing the RED button to Set Limit to prevent it hitting the obstruction.
Use:
Move Continue: Press tu for moving West/East. Press the opposite tu to stop moving.
Move Step(1): Press tu for moving West/East in 0.3° step. Check if you are still well clear of
the obstruction. Then select Set East or West Limit, according to the direction,
and press OK twice to store. Repeat if there is also an obstruction to the
opposite direction. When accidentally selecting satellites from the list which
are out of range by your dish, it will not run in to the obstruction. Both limits
can be disabled with Disable Limit.
7.3.1.3 Channel Scan
Automatic Scan
Satellite Scan: Select a satellite in the left window to be scanned. More than one can be
selected. Press BLUE for Scan. A window with scan settings will be displayed.
Scan Mode: Use tu to select Default, Blind Scan or NetWork.
Default: All stored transponders in the memory will be scanned.
Blind Scan: Slow scan in 2 MHz steps. The receiver will rst scan the whole frequency
band to nd the transponders it can lock on. After gathering all transponders,
it scans the transponders one by one to get all available programmes.
NetWork: Network search will be performed – when network information is broadcast,
new transponders will be found and stored.
Scan type: Press tu to select All Channels (scrambled and free) or FTA Channels (free to
air);
Service Type: Press tu to select ALL, DTV or Radio.
After conguring, press OK or BLUE again to start scanning with the selected settings.
Your receiver will now perform an automatic channel search with the scanning progress shown on
screen. During the channel search you can skip transponders by pressing the MENU button, or quit
the scan process with . When the process has been completed, all found channels will be stored
and the receiver will switch to the rst found channel.
Multi-Satellites Scan: When using a multi feed antenna with more than 1 LNB, select the satellites
your antenna is adjusted to with the OK button. The selected satellites will be
marked by the z symbol. Set the appropriate LNB inputs in the DiSEqC point
and press BLUE for Scan. A window with scanning settings will be displayed.
After conguring the settings like explained in Single Satellite Scan above,
press OK or BLUE again to start Multi-Scan on all selected satellites.
7.3.1.4 Scanning by transponder (Manual Scan)
Press 4 for displaying the transponder list of the highlighted satellite. By pressing Press 4 again you
can switch back to the satellites list.
Single Transponder Scan:
Use the p/q buttons to highlight the transponder you want to scan and
press OK. Press BLUE for Scan. A window with scanning settings will be
displayed. After conguring the settings (explained in 7.3.1.3 above), press
OK or BLUE again to start the scanning of the highlighted transponder. When
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strong SRT 7007 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strong SRT 7007 in the language / languages: English as an attachment in your email.

The manual is 0,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Strong SRT 7007

Strong SRT 7007 User Manual - German - 40 pages

Strong SRT 7007 User Manual - French - 32 pages

Strong SRT 7007 User Manual - Spanish - 35 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info