568528

Strong SRT 7004 Manual

18
Zoom out
Zoom in
Previous page
1/34
Next page
14
PART 1 • English
Transponder list: Press BLUE to delete a transponder from the list. Press
GREEN to delete the selected transponder, select YELLOW to delete all
transponders. Confirm deleting with OK or EXIT to cancel.
Edit: While in the satellite name list: Press RED Edit to enter the Sat Edit window.
Select the satellites position E for East and W for West. Longitude: Use the
numeric keys to enter the longitude of the satellite. Enter a satellite name
with the key table (press u), selecting a character by using the navigation
buttons. Press OK to enter the chosen character. When you have entered the
name, navigate to the “floppy disk-symbol” on screen and press OK on the
remote control to confirm the new name. Save the settings with OK or cancel
by EXIT. While in the Transponder list: Press RED Edit to enter the TP Edit
window.
Frequency: Use the numeric keys to enter a known frequency of the satellite transponder.
Symbol Rate: Use the 0 ~ 9 buttons to enter the symbol rate of the satellite
transponder.
Polarity: Press tu to select the polarization of the satellite transponder. V (Vertical) or
H (Horizontal).
After entering all data, press OK and confirm with OK or press EXIT to leave without saving.
Use GREEN to enter to the Automatic scan window.
Note Deleted satellites and transponders from the pre-installed lists can only be
retrieved by performing a factory reset.
7.1.4 Automatic SAT scan
Select the options if you want to do automatic scan.
Satellite: Select the satellite you wish to scan, as previously set up in the Satellite Setting
menu.
Transponder: Select a transponder which is known to carry a signal to check if reception of
the satellite is possible.
NIT: Network Information Table. If selected On, the receiver will use the NIT
provided by the satellite provider to search for channels. If selected Off, the
receiver will search with its pre-installed transponder list.
Programme: Select Free Only to search for Free to Air channels. Select All to include
scrambled channels as well. Note: Scrambled channels cannot be watched
with this receiver.
Scan Mode: Default TP: All stored transponders in the memory will be scanned.
Blind: Slow scan in 2 MHz steps. The receiver will first scan the whole frequency
band to find the transponders it can lock on. After gathering all transponders,
it scans the transponders one by one to get all available programmes.
One TP: The transponder selected under Transponder will only be scanned.
Scan Select: Select All Sat to search all satellites you have selected in the Satellite Setting
menu. Select Single Sat to search only the satellite selected under Satellite.
After configuring, press GREEN to start scanning with the selected settings.
Your receiver will now perform an automatic channel search with the scanning progress shown
on screen. During the channel search you can quit the scan process with EXIT or MENU. When the
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strong SRT 7004 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strong SRT 7004 in the language / languages: English as an attachment in your email.

The manual is 0,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Strong SRT 7004

Strong SRT 7004 User Manual - German - 40 pages

Strong SRT 7004 User Manual - French - 34 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info