780325
24
Zoom out
Zoom in
Previous page
1/37
Next page
24 25
If you install non-original or the incorrect
replacement parts, this can lead to a severe loss of
function! Tires with bad grip or tires that were not
designed for use in Pedelecs, brake pads with in-
appropriate friction coefficient and wrongly used
or badly designed light-weight components can
cause accidents with the most severe of conse-
quences. The same applies for improper assembly!
Screws and torque spanners
When working on the Pedelec, please en-
sure that all screws are tightened to the correct
torque. The required torque is printed on many
parts with a screwed connection. This amount is
stated in Newton meters (Nm) and this work
should be carried out using a torque wrench. Best
suited are torque wrenches that slip and provide
an acoustic signal when the predefined fastening
torque is reached. Otherwise, screws may snap or
break. If you don’t own a torque wrench then you
should always leave this work to a Stromer dealer!
A table with the most important fastening torques
for screw connections is provided in the “Screw
connections” section.
Torque spanners
Open live parts should only be maintained and
cleaned at a Stromer dealer!
Remove the battery before cleaning your
Pedelec. Ensure that the battery box is again
completely closed.
Ensure that you do not touch and thus possibly
connect contacts when cleaning the battery.
You risk being hurt and the battery may suffer
damage if the contacts are live.
Cleaning with a high-pressure cleaner may
damage the electrical system. The high pres-
sure might also push cleaning liquid into
sealed parts and thus damage them.
Avoid damage to cables and electrical compo-
nents. When this has happened, the Pedelec
must be deactivated until it has been inspected
by a Stromer dealer!
Switch off the electrical system, remove the
battery and close the battery box before perform-
ing any kind of work on your Pedelec.
Chain / Drive
The drive chain must be regularly cleaned and
lubricated to ensure appropriate functioning (see
the “Deadlines and inspection work” section). Dirt
can be removed with the normal pedelec wash.
Otherwise you can clean the chain by rubbing
it with an oily cloth. When the chain is clean, it
should be greased at the joints with suitable lubri-
cant. After being left to soak, the excess lubricant
should then be removed.
Chain tension
To ensure that the chain and gears can work safe-
ly, the chain must have a certain level of tension.
Otherwise it can come off and lead to a fall. Chain
gear systems tense the chain automatically.
Dirt and permanent strain wear the chain.
The chain should be replaced as soon as it can be
significantly lifted (approx. 5 mm) from the front
chain ring with your fingers.
Replacement of the chain is to be expected after
approx. 1500 km, depending on the load.
Chain OK
Chain worn
Many modern chains for derailleur gear systems
no longer have chain connectors. Special tools
are required to open/exchange/close them. They
should be exchanged by a Stromer dealer.
Other chains are supplied/mounted with chain
joints. In some cases, these can be opened with-
out the need for tools. These chain connectors can
also be used to repair a damaged chain on a ride,
if they have the correct width for the drive train.
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stromer Pedelec 2017 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stromer Pedelec 2017 in the language / languages: English as an attachment in your email.

The manual is 1.07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Stromer Pedelec 2017

Stromer Pedelec 2017 User Manual - German - 38 pages

Stromer Pedelec 2017 User Manual - Dutch - 39 pages

Stromer Pedelec 2017 User Manual - French - 38 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info