790823

Strom E-Boiler Manual

12
Zoom out
Zoom in
Previous page
1/44
Next page
www.stromltd.com
STROM LIMITED 2021
12
SYSTEM PIPING
Electric Boilers
The boiler must be installed by a competent and certied plumber or heating engineer and systems should be
designed to meet the current building regulations in force at the time of installation.
Strom Limited are not responsible for faulty installations which are performed by unqualied tradespeople.
DESIGN NOTES:
ISOLATION VALVES:
For ease of removal from the system, it is recommended that full bore isolation valves are tted on the ow and
return pipework from the boiler. Do not use standard ball valves, as this can restrict the ow in and out of the
boiler and result in detrimental performance.
AUTOMATIC AIRVENTS
An automatic air vent is already built into the boiler. However, if the boiler is to be used in tandem with a hot
water cylinder, an additional air vent should be tted in the vicinity of the cylinder coil. An airvent should always
be considered at the highest point in a system to aid in purging the system of any air.
AUTOMATIC BYPASS VALVE
An automatic bypass valve is integral to any system and MUST be installed as part of this installation. The
ABV should be tted to begin opening as the rst valve, radiator, or actuator shuts in the system, this stops
excess pressure from building in the system on the ow side. Failure to t and set the ABV can result in poor
performance and premature boiler failure.
WATER CONNECTIONS
For lling the heating system, reference should be made to BS EN 14336. There must be no connection
between the central heating systems and the main water supply, and all local water bylaws must be
observed. Any connection made between the mains water and heating system must be disconnected
after use.
WATER PURGES
Install purges in the radiators and any high points in the heating system to aid in removing air.
DRAIN POINT
A drain point should be tted at the lowest point of the heating system. It is not acceptable to drain the boiler
through a safety valve as debris can prevent the correct operation of the valve.
HEATING EXPANSION VESSEL
An expansion vessel is tted internally within the boiler to provide room for thermal expansion of water under
regular operating conditions. However, if the system contains signicant volumes of water, an additional heating
expansion vessel should be tted externally.
… 12 …


Need help? Post your question in this forum.

Forumrules
1

Forum

strom-e-boiler

Reset search

  • After turning off heater, I cannot turn it back on. The Menu button does not work. Submitted on 5-4-2023 at 16:40

    Reply Report abuse

  • the front panel is flashing E5 and I can not change anything Submitted on 13-12-2022 at 13:27

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Strom E-Boiler at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Strom E-Boiler in the language / languages: English as an attachment in your email.

The manual is 3.36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info