813433

Stovax Riva - Woodburning and Multi-fuel Manual

29
Zoom out
Zoom in
Previous page
1/40
Next page
29
Maintenance & Servicing
3.1 To maintain safe use of the appliance damaged door glass
must be replaced immediately. To complete this operation
remove the door see Section 2 in the Pre-Installation section.
Door Rope Seal
Fixing Screw
Trim/Frame
Glass Edge
Seal Tape
Glass
Trim/Frame
Door
1Riva Avanti
Door Rope Seal
Fixing Screw
Trim/Frame
Glass Edge
Seal Tape
Glass
Door
2Riva
Freestanding
3.2 Lay the door face down on a soft flat surface, to protect the
paintwork and glass.
3.3 Remove the old door rope seal and scrape old glue from the
locating groove. Clean the locating groove with a clean, dry
cloth to remove all old dust and debris.
3.4 Use a 2.5mm A/F hexagon key to remove the exposed fixing
screws in the rope seal locating groove.
3.5 Remove the trim/frame.
The old glass can then be lifted clear of the door.
(Note how the edge sealing tape is fixed.)
3.6 Dispose of the old glass safely.
3.7 Clean and re-paint the rear of the door if required.
Clean the screws with light oil and coat with high
temperature anti-seize grease, this will aid future removal.
3.8 Fit the edge sealing tape to the new glass and place the
glass into position in the door.
3.9 Place the door trim/frame back in to position and re-fix with
the clean fixing screws.
Do not over tighten the clips as this could break the glass.
3.10 Squeeze a generous bead of fresh Stovax Thermic Seal
glue into the rope locating groove.
Do not glue over the screw heads.
3.11 Press the new Stovax door sealing rope into the locating
groove, placing the joint in the middle of the lower edge of
the door.
Refit the door on to the appliance and close the door to
apply pressure to new rope.
Leave the door closed for at least 12 hours before
lighting the appliance and run at a low temperature for
approximately one day. This allows the adhesive to fully
bond to the seal.
3.12 Fit only original Stovax ceramic glass, which is suitable to
use in high temperature applications.
3.13 Using the appliance with a damaged door glass could cause
dangerous fumes to enter the room, or the appliance to over
fire, resulting in damage.
4. Fitting A New Door Seal - All Models
4.1 To maintain the safe use of your appliance you need to
replace damaged or worn door sealing rope. To complete
this operation remove the door see Section 2 in the Pre-
Installation section.
4.2 Lay the door face down on a soft flat surface, to protect the
paintwork and glass.
4.3 Remove the old rope and scrape old glue from the locating
groove. Clean the locating groove with a clean dry cloth to
remove all old dust and debris.
4.4 Squeeze a generous bead of fresh Stovax Thermic Seal
glue into the rope locating groove.
4.5 Press the new Stovax rope into the locating groove, placing
the joint in the middle of the lower edge of the door.
4.6 Refit the door and close the door to apply pressure to the
new rope.
Leave the door closed for at least 12 hours before
lighting the appliance and run at a low temperature for
approximately one day. This allows the adhesive to fully
bond to the seal.
4.7 Using the appliance with a damaged door seal can cause
dangerous fumes to enter the room, or the appliance to over
fire, resulting in damage.
5. Adjusting the Door Catch
To maintain the safe use of your Riva, you may need to adjust
the door catch to ensure safe correct closing of the door.
… 29 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stovax Riva - Woodburning and Multi-fuel at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stovax Riva - Woodburning and Multi-fuel in the language / languages: English as an attachment in your email.

The manual is 5.3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info