597139
48
Zoom out
Zoom in
Previous page
1/52
Next page
48
TROUBLESHOOTING
If a solution to your problem is not listed below, please call our technical support team (see below).
PROBLEM
POSSIBLE CAUSES
SOLUTIONS
System is not receiving power, or
is not powering up.
Cable from power adapter is loose or
unplugged.
Confirm that all cables are connected correctly.
Confirm that the power adapter is securely connected to the
back of the unit.
Cables are connected but system is not
receiving sufficient power.
Confirm the system is powered on (LED indicators on front
panel should be on)
If the DVR is connected through a power bar or surge protector,
try bypassing it and connecting power directly from the mains
socket to the DVR.
Confirm that there is power at the outlet.
Remote control is not detected by
the system.
Batteries in the remote control are
drained.
Install 2x fresh AAA 1.5V alkaline batteries in the remote
control. Ensure correct orientation.
There are no batteries in the remote
control.
Hard Disk Drive (HDD) is not
detected by the system.
HDD cables are loose or not connected
properly.
Remove the housing and check that the cables are firmly
connected.
There is no HDD in the system.
Open the housing and install a 3.5” SATA HDD (up to 2TB).
HDD is full and the unit is no
longer recording
Overwrite mode is not enabled.
Check configuration in Main Menu System General.
Mouse not detected by the
system.
Mouse cable not firmly connected to
the system.
Firmly connect the mouse cable to the USB port on the rear
panel of the DVR.
Mouse is not connected to the system.
System needs to be reset.
Power off the system (disconnect power cable). Firmly connect
a USB mouse to the USB port on the rear panel of the DVR.
Reconnect the power cable to the DC 12V port.
There is no picture on selected
channels / camera picture is not
being displayed.
Camera cables are loose or have been
disconnected.
Check the camera video cable and connections.
Disconnect and reconnect the cable at both the system and
camera ends.
Reconnect the camera to another channel or use another cable.
There is no sound from attached
cameras.
Audio cables are loose or have been
disconnected.
Check the audio connections to the DVR.
Audio channels are disabled in the
system menu.
Check configuration in Main Menu System Encode.
Volume on external speakers (not
included) is low / muted / off.
Increase volume on external speakers (not included).
A “whirring” noise is coming from
the system.
Fan is active.
This is normal the exhaust fan is working.
The system beeps at start up.
This is normal.
The system beeps during motion
detection.
Motion detection is enabled and the
alarm buzzer is activated.
Check configuration in Main Menu Alarm Alarm Input.
WARRANTY AND TECHNICAL SUPPORT
Support:
www.storageoptions.com/support/
Warranty:
www.storageoptions.com/warranty/
48


Need help? Post your question in this forum.

Forumrules
1

Forum

storage-options-52399---4-channel-cctv-dvr

Reset search

  • which leads do you connectet the cameras to on the multiplug at thr rear of the recorder Submitted on 19-2-2020 at 17:50

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Storage Options 52399 - 4 Channel CCTV DVR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Storage Options 52399 - 4 Channel CCTV DVR in the language / languages: English as an attachment in your email.

The manual is 4,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info