Manual Stomer SRF-40 (page 8 of 28) (English, German, French)

555302

Zoom out

Zoom in

1/28

VOLUME MEASUREMENT

For volume measurements, push button 6. The indica-

tor for volume measurement appears in the display .

Afterwards, measure the length, width and the height,

one after another, in the same manner as for a length

measurement. The laser beam remains switched on

between all three measurements.

After taking the third measurement, the volume is auto-

matically calculated and displayed. The last individual

measured value is indicated at the bottom in the dis-

play, while the ﬁ nal result is shown at the top.

CONTINUOUS MEASUREMENT

For continuous measurements, the measuring tool can

be moved relative to the target, whereby the measur-

ing value is updated approx. every 0.5 seconds. In this

manner, as an example, you can move a certain dis-

tance away from a wall, while the actual distance can

always be read. For continuous measurements, push

button 1.

Press the measuring button 1 to initiate the measuring

procedure. Move the measuring tool until the required

distance value is indicated at the bottom of the dis-

play.

Pushing the measuring button 1 interrupts the continu-

ous measurement. The current measured value is in-

dicated in the display. Repeated pushing of the meas-

uring button 1 starts the continuous measuring again.

The continuous measurement automatically switches

off after 5 minutes.

WORKING ADVICE

GENERAL INFORMATION

The reception lens 5 and the laser beam outlet 4 must

not be covered when

taking a measurement.

The measuring tool must not be moved while taking

a measurement (with the exception of the continuous

measurement function). Therefore, place the measur-

ing tool, as far as this is possible, against or on the

measuring points.

Measurement takes place at the centre of the laser

beam, even when target surfaces are sighted at an

incline.

Inﬂ uence Effects on the Measuring Range The meas-

uring range depends upon the light conditions and the

reﬂ ection properties of the target surface.

Aim the laser beam at the target surface. Push the

measuring button 1 again to initiate the measurement.

In the tracking function, the measurement already

starts upon ﬁ rst actuation of the measuring button 1.

Typically, the measured value appears after 0.5 and

latest after 4 seconds. The duration of the measure-

ment depends on the distance, the light conditions and

the reﬂ ection properties of the target surface. The end

of the measurement is indicated by a signal tone. The

laser beam is switched off automatically upon comple-

tion of the measurement.

When no measurement has taken place approx. 20

seconds after sighting, the laser beam is switched off

automatically to save the batteries.

SELECTING THE REFERENCE LEVEL

Two different reference levels are available for meas-

uring:

– The rear edge of the measuring tool (e.g. when plac-

ing against a wall),

– The front measuring-tool edge (e.g. when measuring

onward from a table edge).

To change the reference level, press button 2 until the

requested reference level is indicated on the display.

Each time after switching on the measuring tool, the

rear end of the measuring tool is preset as the refer-

ence level.

MEASURING FUNCTIONS

LENGTH MEASUREMENT

For length measurement, push button 6. The indicator

for length measurement appears in the display.

Push the measuring button 1 once for sighting and

once more to take the measurement. The measured

value is indicated at the bottom in the display.

AREA MEASUREMENT

For area measurements, push button 6. The indicator

for area measurement appears in the display.

Afterwards, measure the length and the width, one af-

ter another, in the same manner as a length measure-

ment. The laser beam remains switched on between

both measurements.

After taking the second measurement, the area/surface

is automatically calculated and displayed. The last indi-

vidual measured value is indicated at the bottom in the

display, while the ﬁ nal result is shown at the top.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stomer SRF-40 in the language / languages: English, German, French as an attachment in your email.

The manual is 0,57 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stomer SRF-40 Manual

Product: