555292
14
Zoom out
Zoom in
Previous page
1/28
Next page
14
Do not lengthen the spanner, so that you can exercise
more power.
Do not hit on the spanner with a hammer, for tightening
the shaft.
The spanner must be removed, after the shaft that has
been tightened.
Install the saw table and mount the corresponding
screws.
REPLACING THE SAW GUIDE
HAZARD!
If the saw guide has been damaged, then small pieces
can become jammed between the guide and the saw,
which can block the saw blade. Immediately replace a
defective saw guide.
Remove the saw guide.
Remove the defective piece by dislodging it with a
screwdriver.
Insert a new piece and click it in position.
Reinstall the saw guide.
MODIFICATIONS
MODIFICATIONS ON THE MITRE AND WIDTH
GUIDE
Loosen the attachment screws of the guide.
Adapt the guide so that it is positioned exactly at right
angles to the saw blade, when the mitre table is in the 0°
position.
Retighten the attachment screws of the guide.
ADAPTING THE SAWING DEPTH STOP
The sawing depth stop limits the depth to which the saw
extends in the saw blade opening.
The saw depth stop must be adapted, if the saw blade
makes contact with the table.
Loosen the attachment screw of the saw depth stop.
Adapt the saw depth stop in such a way that the saw
blade extends up to the mitre and depth guide in the saw
blade opening.
Retighten the attachment screws of the saw depth stop.
Lower the saw head until it is stopped by the saw depth
stop, and check whether the saw blade can freely rotate
in this position.
CLEANING
Use a brush, a dust cloth or vacuum cleaner, to remove all
wood chips and sawdust from:
The adjustment facilities
The operating components
The motor ventilation openings
The space under the table gap.
Set the support arm to 0° (vertical) and tighten the
bevelling lock nut.
To prevent that the saw blade rotates, pull the saw blade
lock forward. Use your hand at the same time to turn the
saw blade slowly, until the saw blade latch is activated.
Loosen the driveshaft bolt of the saw (left-turning
thread).
Remove the shaft bolt and the outer saw ange from the
saw shaft.
Remove the saw blade from the saw shaft and let it down
to remove it from the machine.
Remove the adapter ring and the inner saw ange from
the saw shaft.
Clean the surfaces of the following components:
The saw shaft
The inner saw ange
The saw blade
The outer saw ange
– adapter ring
The saw blade guard
HAZARD! Do not use any cleaning products (for
instance for removing resin residues) that have
the tendency to cause corrosion on light metals;
this could damage the machine.
Put the inner saw ange and the adapter ring on the saw
shaft.
HAZARD! Be sure to fasten the inner saw ange
correctly! The saw may block, or the saw blade
may come lose, if the ange is not correctly
fastened.
Mount the new saw blade and check the rotating direction
(the arrow on the saw blade must point in the same
direction as the arrow on the saw blade guard!).
HAZARD! Only use saw blades that conform to
the applicable standards and that can be used at
the maximum speed indicated in the technical
data sheet.
DO NOT use:
Wrong saw blades
Saw blades made of high-speed steel (HSS)
Damaged saw blades
Saw blades with missing teeth
HAZARD!
Only use OEM components for installing the saw blade.
Do not use loose reduction rings; the saw blade could
come loose.
Saw blades must be mounted in such a way that they
cannot wobble, and that they cannot come loose during
operations.
Install the outer saw ange.
The two anges must t over the surfaces of the saw
shaft.
Insert the shaft bolt (left-turning thread) and tighten with
a hexagonal spanner.
HAZARD!
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stomer SMS-1800-T at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stomer SMS-1800-T in the language / languages: English as an attachment in your email.

The manual is 1,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info