Manual Stomer SHD-1500-K (page 8 of 88) (All languages)

555249

Zoom out

Zoom in

1/88

Products sold in AUS and NZ only: Use a residual cur-

rent device (RCD) with a rated residual current of 30

mA or less.

ASSEMBLY

AUXILIARY HANDLE

● Operate your machine only with the auxiliary handle

7. The auxiliary handle 7 can be set to any position

for a secure and low-fatigue working posture.

Loosen the knurled nut 8, rotate the auxiliary handle 7

around the axis of the machine to the required position

and tighten the knurled nut 8 again.

The auxiliary handle 7 can be mounted to a different

position. For this, completely unscrew the knurled nut 8

and then pull out the hexagon bolt upward. Pull off the

auxiliary handle 7 to the side and turn around the re-

maining clamping element by 180°. Mount the auxiliary

handle 7 in reverse order.

CHANGING THE TOOL

● Before any work on the machine itself, pull the mains

plug.

With the SDS-max tool holder, simpler and easier tool

changing is possible without additional aids.

The dust protection cap 1 largely prevents the entry of

drilling dust into the tool holder during operation. When

inserting the tool, take care that the dust protection cap

1 is not damaged.

● A damaged dust protection cap should be changed

immediately.

We recommend having this carried out by an after-

sales service.

Inserting (see ﬁ gure A)

Clean and lightly grease the shank end of the tool.

Insert the tool in a twisting manner into the tool holder

until it latches itself.

Check the latching by pulling the tool.

Removing (see ﬁ gure B)

Push back the locking sleeve 2 and remove the tool.

DUST/CHIP EXTRACTION

● Dusts from materials such as lead-containing coa-

tings, some wood types, minerals and metal can be

harmful to one’s health. Touching or breathing-in the

dusts can cause allergic reactions and/or lead to re-

spiratory infections of the user or bystanders.

Certain dusts, such as oak or beech dust, are consi-

dered as carcinogenic, especially in connection with

wood-treatment additives (chromate, wood preserva-

tive). Materials containing asbestos may only be wor-

ked by specialists.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 ﬁ lter-class respira-

tor.

Observe the relevant regulations in your country for the

materials to be worked.

● Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained

users.

● Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s ope-

ration. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

● Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges

are less likely to bind and are easier to control.

● Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into ac-

count the working conditions and the work to be per-

formed. Use of the power tool for operations diffe-

rent from those intended could result in a hazardous

situation.

Service

● Have your power tool serviced by a qualiﬁ ed re-

pair person using only identical replacement parts.

This will ensure that the safety of the power tool is

maintained.

HAMMER SAFETY WARNINGS

● Wear ear protectors. Exposure to noise can cause

hearing loss.

● Use auxiliary handle(s), if supplied with the tool.

Loss of control can cause personal injury.

● Hold power tool by insulated gripping surfaces,

when performing an operation where the cutting ac-

cessory may contact hidden wiring or its own cord.

Cutting accessory contacting a “live” wire may ma-

ke exposed metal parts of the power tool “live” and

could give the operator an electric shock.

● Use suitable detectors to determine if utility lines

are hidden in the work area or call the local utility

company for assistance. Contact with electric lines

can lead to ﬁ re and electric shock. Damaging a gas

line can lead to explosion. Penetrating a water line

causes property damage or may cause an electric

shock.

● When working with the machine, always hold it ﬁ rm-

ly with both hands and provide for a secure stance.

The power tool is guided more secure with both

hands.

● Secure the workpiece. A workpiece clamped with

clamping devices or in a vice is held more secure

than by hand.

● Always wait until the machine has come to a com-

plete stop before placing it down. The tool insert can

jam and lead to loss of control over the power tool.

Products sold in GB only: Your product is ﬁ tted with

a BS 1363/A approved electric plug with internal fuse

(ASTA approved to BS 1362).

If the plug is not suitable for your socket outlets, it

should be cut off and an appropriate plug ﬁ tted in its

place by an authorised customer service agent. The

replacement plug should have the same fuse rating as

the original plug.

The severed plug must be disposed of to avoid a pos-

sible shock hazard and should never be inserted into a

mains socket elsewhere.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stomer SHD-1500-K in the language / languages: All languages as an attachment in your email.

The manual is 1,93 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stomer SHD-1500-K Manual

Product: