555253
8
Zoom out
Zoom in
Previous page
1/92
Next page
8
GB
OPERATION
Starting Operation
Observe correct mains voltage! The voltage of the
power source must agree with the voltage speci-
ed on the nameplate of the machine. Power tools
marked with 230 V can also be operated with
220 V.
Reversing the Rotational Direction
The rotational direction switch 8 is used to reverse the
rotational direction of the machine.
However, this is not possible with the On/Off switch 7
actuated.
Right rotation: For driving in screws, push the rotational
direction switch 8 left to the stop.
Left rotation: Push the rotational direction switch 8 right
to the stop (for unscrewing screws).
Switching On and Off
To start the machine, press the On/Off switch 7 and
keep it depressed.
To lock the pressed On/Off switch 7, press the lock-on
button 6.
To switch off the machine, release the On/Off switch
7 or when it is locked with the lock-on button 6, brie y
press the On/Off switch 7 and then release it.
Adjusting the Speed
The speed of the switched on power tool can be vari-
ably adjusted, depending on how far the On/Off switch
7 is pressed.
Light pressure on the On/Off switch 7 results in a low
rotational speed. Further pressure on the switch results
in an increase in speed.
Adjusting the Screw-in Depth (see gure B)
With the adjustment sleeve 3, the screw-in depth of the
screw head into the workpiece can be preset in 8 lock-
ing steps per full turn. Each step corresponds with a
0.25 mm change of the screw-in depth.
Turning the adjustment sleeve 3 in clockwise direction
results in a greater screw-in depth; turning in anticlock-
wise direction reduces the screwin depth.
The required setting is best determined by testing.
WORKING ADVICE
Apply the power tool to the screw only when it is
switched off. Rotating tool inserts can slip off. Guide
the screw toward the screwdriving bit 1.
The screw is held in place by the magnet pull of the
universal bit holder 9. Firmly push the tip of the screw
into the material to be screwed until the screwing-depth
stop 4 faces against the workpiece.
Switch the machine on. The screw is screwed into the
material until the adjusted screw-in depth is reached.
The drive is disengaged and the tool holder no longer
rotates. Check the screw-in depth and readjust, if re-
quired.
For unscrewing screws, set the rotational direction
switch 8 to left rotation and pull off the screwing-depth
stop 4 toward the front without turning the adjustment
sleeve. Working with the screwing-depth stop 4 is also
possible when adapting the screw-in depth.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s opera-
tion. If damaged, have the power tool repaired before
use. Many accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean. Properly main-
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into account
the working conditions and the work to be performed.
Use of the power tool for operations different from
those intended could result in a hazardous situation.
5) Service
a) Have your power tool serviced by a quali ed repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
MACHINE-SPECIFIC SAFETY WARNINGS
Hold the machine with a rm grip. High reaction
torque can brie y occur while driving in and loosen-
ing screws.
Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure
than by hand.
Always wait until the machine has come to a com-
plete stop before placing it down. The tool insert can
jam and lead to loss of control over the power tool.
Never use the machine with a damaged cable. Do
not touch the damaged cable and pull the mains
plug when the cable is damaged while working.
Damaged cables increase the risk of an electric
shock.
FUNCTIONAL DESCRIPTION
Read all safety warnings and all instructions. Failure
to follow the warnings and instructions may result in
electric shock, re and/or serious injury.
While reading the operating instructions, unfold the
graphics page for the machine and leave it open.
INTENDED USE
The machine is intended for driving in and loosening
screws.
ASSEMBLY
Changing the Tool (see gure A)
Pull off the screwing-depth stop 4 toward the front. Pull
out the screwdriver bit 1. If required, the universal bit
holder 9 can also be pulled off and replaced.
After changing the tool, reattach the screwingdepth
stop 4.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stomer SCD-750 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stomer SCD-750 in the language / languages: All languages as an attachment in your email.

The manual is 1,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info