555255
6
Zoom out
Zoom in
Previous page
1/56
Next page
6
Angle grinder
INTENDED USE
This tool is intended for grinding, cutting and deburring
metal and stone materials without the use of water; with
the appropriate accessories the tool can also be used for
brushing and sanding
TECHNICAL SPECIFICATIONS 1
PRODUCT ELEMENTS 2
1. Spindle
2. Clamping ange
3. Spanner
4. Spindle-lock button
5. Auxiliary handle
6. Safety guard
7. Mounting ange
8. On/off locking switch
SAFETY
WARNING! Read all instructions. Failure to follow all in-
structions listed below may result in electric shock, re
and/or serious injury.
Only use this tool for dry grinding/cutting
Only use the anges which are supplied with this tool
This tool should not be used by people under the age of
16 years
• Always disconnect plug from power source before
making any adjustment or changing any accessory
ACCESSORIES
Use the original SBM Group accessories which can be
obtained from your SBM Group dealer
For mounting/using non- SBM Group accessories ob-
serve the instructions of the manufacturer concerned
Use only accessories with an allowable speed matching
at least the highest no-load speed of the tool
Do not use damaged, deformed or vibrating grinding/
cutting discs
Handle and store grinding/cutting discs carefully to
avoid chipping and cracking
Protect accessories from impact, shock and grease
Do not use a grinding/cutting disc that is larger than the
maximum recommended size
Only use grinding/cutting discs with a hole diameter
which ts mounting ange (7) without play; never use
reducers or adaptors to t large-hole grinding/cutting
discs
Never use grinding/cutting discs with a threaded hole,
of which the thread is not long enough to accept the spin-
dle length of the tool
Never use accessories with a “blind” threaded hole
smaller than M14 x 21 mm
OUTDOOR USE
Connect the tool via a fault current (FI) circuit breaker
with a triggering current of 30 mA maximum
Only use an extension cord which is intended for out-
door use and equipped with a splashproof coupling-sock-
et
BEFORE USE
Before using the tool for the rst time, it is recommend-
ed to receive practical information
Do not work materials containing asbestos (asbestos is
considered carcinogenic)
Take protective measures when during work dust can
develop that is harmful to one’s health, combustible or ex-
plosive (some dusts are considered carcinogenic); wear a
dust mask and work with dust/chip extraction when con-
nectable
• Be careful of hidden electrical wires or gas- and water
pipes; check the work area, for instance with a metal de-
tector
Be careful when cutting grooves, especially in support-
ing walls (slots in supporting walls are subject to country-
specic regulations; these regulations are to be observed
under all circumstances)
Clamp the workpiece in case it does not remain
stationa ry from its own weight
Do not clamp the tool in a vice
Use completely unrolled and safe extension cords with
a capacity of 16 Amps (UK 13 Amps)
Wear protective glasses and gloves, hearing protection
and sturdy shoes; when necessary, also wear an apron
Always mount auxiliary handle (5) and protective guard
(6); never use the tool without them
Be sure tool is switched off when plugging in
DURING USE
Always keep the cord away from moving parts of the
tool; direct the cord to the rear, away from the tool
If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug;
never use the tool with a damaged cord
Push spindle-lock button (4) only when spindle (1) is at
a standstill
Keep hands away from rotating accessories
When grinding metal, sparks are generated; keep other
persons and combustible material from work area
In case of electrical or mechanical malfunction, immedi-
ately switch off the tool and disconnect the plug
In case the cutting disc is blocked, resulting in jerking
forces on the tool, immediately switch off the tool
In case of current interruption or when the plug is ac-
cidentally pulled out, unlock the on/off switch (8) imme-
diately and put it in the OFF-position in order to prevent
uncontrolled restarting
Do not apply so much pressure on the tool that it comes
to a standstill
AFTER USE
• Before you put down the tool, switch off the motor and
ensure that all moving parts have come to a complete
standstill
After switching off the tool, never stop the rotation of the
accessory by a lateral force applied against it
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
Do not connect the blue (= neutral) or brown (= live)
wire in the cord of this tool to the earth terminal of the
plug
English
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stomer SAG-600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stomer SAG-600 in the language / languages: All languages as an attachment in your email.

The manual is 3,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info