555308
6
Zoom out
Zoom in
Previous page
1/44
Next page
6
Cordless drill/driver
INTENDED USE
• This tool is intended for drilling in wood, metal, ceramic
and plastic; tools with electronic speed control and left/right
rotation are also suitable for screwdriving and thread cut-
ting
TECHNICAL SPECIFICATIONS 1
PRODUCT ELEMENTS 2
1 Switch for on/off and speed control
2 Switch for changing direction of rotation
3 Keyless chuck
4 Ring for torque control
5 Switch for selecting mechanical speed
SAFETY
WARNING! Read all instructions. Failure to follow all in-
structions listed below may result in electric shock, re
and/or serious injury.
• Ensure the switch is in the off position before inserting
battery pack. Inserting the battery pack into power tools
that have the switch on invites accidents.
• Recharge only with the charger speci ed by the manu-
facturer. A charger that is suitable for one type of battery
pack may create a risk of re when used with another bat-
tery pack.
• Use power tools only with speci cally designated battery
packs. Use of any other battery packs may create a risk
of injury and re.
Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the charger (charg-
ers with a rating of 230V or 240V can also be connected
to a 220V supply)
• In case of electrical or mechanical malfunction, imme-
diately switch off the tool or unplug charger from power
source
• SBM Group can assure awless functioning of the tool
only when original accessories are used
• Use only accessories with an allowable speed matching
at least the highest no-load speed of the tool
• This tool should not be used by people under the age
of 16 years
• Be careful not to drill or drive into areas where electrical
wires may be contacted
• Ensure that switch (2) is in the middle (locking) position
before making any adjustments or changing accessories
as well as when carrying or storing the tool
• Do not touch the contacts in the charger
• Do not expose tool/charger/battery to rain
• Never charge battery outdoors
• Store tool/charger/battery in locations where tempera-
ture will not exceed 40° C or drop below 0° C
• Batteries will explode in re, so do not burn battery for
any reason
• When damaged, and under extreme usage and tem-
perature conditions, batteries may start to leak
- if liquid comes into contact with the skin, wash quickly
with soap and water, then with lemon juice or vinegar
- if liquid gets into the eyes, ush eyes with clean water
for a minimum of 10 minutes and seek immediately medi-
cal attention
• When battery is not in tool or charger, it should be kept
away from metal objects such as nails, screws, keys etc.
to prevent short-circuit
• Do not use charger when damaged; take it to one of
the of cially registered SBM Group Service Stations for
a safety check
• Do not use battery when damaged; it should be re-
placed immediately
• Do not disassemble charger or battery
• Do not attempt to recharge non-rechargeable batteries
with the charger
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live)
wire in the cord of the charger to the earth terminal of
the plug
• If for any reason the old plug is cut off the cord of the
charger, it must be disposed of safely and not left unat-
tended
To ensure longer service life and proper per-
formance of the battery, take the following ac-
tions when you start using new battery:
1. Use the new battery, without recharging it, till its com-
plete discharge.
2. Then charge the battery for 1 hour.
3. Repeat abovementioned actions (1 and 2) 3-5 times to
reach the nominal battery capacity.
MAINTENANCE
Make sure that the machine is not live when
carrying out maintenance work on the motor.
Regularly clean the machine housing with a soft cloth,
preferably after each use. Keep the ventilation slots free
from dust and dirt.If the dirt does not come off use a soft
cloth moistened with soapy water. Never use solvents
such as petrol, alcohol, ammonia water, etc. These sol-
vents may damage the plastic parts.
The machine requires no additional lubrication.
Should a fault occur, e.g. after wear of a part, please con-
tact your local SBM Group dealer.
ENVIRONMENT
In order to prevent the machine from damage during
transport, it is delivered in a sturdy packaging. Most of the
packaging materials can be recycled. Take these materi-
als to the appropriate recycling locations. Take your un-
wanted machines to your local SBM Group dealer. Here
they will be disposed of in an environmentally safe way.
NiCd batteries can be recycled. Deliver them to a disposal
site for chemical waste so that they can be recycled or dis-
posed of in an environmentally friendly manner.
English
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stomer SAD-14x2-D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stomer SAD-14x2-D in the language / languages: All languages as an attachment in your email.

The manual is 1,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info