Manual Stokke XPLORY V1 (page 22 of 39) (All languages)

626070

Zoom out

Zoom in

1/39

STOKKE

XPLORY

Disassembling the fabric

components for washing:

Disassembling the hood (20)

Unzip to release the hood. Unbutton

on each side of the hood. Pull up the

fabric on the side and the front to

reveal the hood fastener. Press the

notch on the hood fastener and pull

up the hood. Repeat at the other side.

Remove the main rib before washing.

Disassembling the back cover (21)

Loosen the fabric from the push

buttons on each side and from the two

in front. Pull the fabric off the Velcro.

Disassembling the fabric on the seat

guard (22)

Release the rib by pressing a thin pin

or screwdriver into the little hole on

each side. Open textile tab and unzip.

Loosen the fabric from the hook on

both side of the rib.

Disassembling Seat rail cover

Remove by pulling off.

Disassembling Harness covering

Remove by pulling off.

Disassembling Seat cover (23)

Loosen the orange tag on each side of

the bottom rear of the back. Remove

the safety harness. Gently pull the

seat fabric up until it is completely off.

MAINTENANCE – WASHING

INSTRUCTIONS

Hard parts

The stroller should be cleaned using

a mild mixture of soap and water.

Make sure that any sand/mud/grit is

removed prior to cleaning. No part of

the stroller is to be lubricated. If any

function of the stroller is not working

properly, contact your

nearest STOKKE retailer.

Textiles must be washed separately

(24)

• When washing the baby insert,

please remove the inside cushion

before washing the cover.

• Remove the ribs before washing

the canopy. Release the main rib by

pressing, e.g., a screwdriver into

the small holes in the canopy

fasteners. Afterwards, thread all

the ribs out of the fabric.

Assembling the fabric components after

washing:

Assembling the Seat cover (25)

Insert the rails on the seat cover into

the slot on each side. Pull the seat cover

down. Position the harness. Crotch, waist

and shoulder straps. Make sure that

shoulder straps

correspond to the child’s shoulder height.

Fasten the orange tag on each side of the

bottom rear of the back. Conceal the end

of the orange tag in the seat. Pull the fab-

ric over the back.

Assembling the fabric on the seat guard

(26)

Release the rib by pressing a thin pin or

screwdriver into the little hole on each

side. Fasten the beginning of the zipper

around the bar with Velcro facing out.

Make sure that the tap goes through the

fabric. Pull up the zip with tap through

center and end. Fasten the rib by pressing

it into place.

Note! The rib can be mounted wrong!

Assembling the back cover (27)

Line up the center mark on the fabric to

the corresponding center mark on the

seat guard. Attach the cover edge-to-

edge on the Velcro. Attach the cover with

the push buttons, 2 on each side, and with

the two on each side of the front.

Assembling the hood (28)

Insert the main rib after washing. Make

sure the notch on the main rib is facing

front. Insert the main rib into both sides

of the hood fastener. A click will be heard

when the rib is placed correctly. Fasten

the hood with the push buttons on each

side. Zip the hood onto the seat fabric.

Assembling the harness covering

Enter the harness covering with the soft

side facing the child.

Assembling the seat rail cover

Enter the cover by pulling it on.

Basic mosquito net (29)

Pull the mosquito net over the handle and

the footrest. Pull the mosquito net over

the main rib of the hood. Snap on the

mosquito net using the push

buttons on each side. Pull the net until

the seat is completely covered. Pull up

the zippers on each side of the central

bar.

Basic rain cover(30)

Pull the rain cover over the handle and

the footrest. Pull the rain cover over the

hood. Fasten using the Velcro around the

central bar and footrest. Pull up the

zippers on each side of the central bar.

Basic shopping bag(31)

Place the shopping bag on the board.

Fasten around the central bar using

the attached hook.

Changing bag

Attach the changing bag to the seat

arm.

Stokke® Warranty card / Product

registration card:

See description of where to find the

products serial number/date clock on

your product. Use this information

when filling out the Stokke warranty

card / Product registration card. We

recommend that you fill in this

information at www.stokke.com.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stokke XPLORY V1 in the language / languages: All languages as an attachment in your email.

The manual is 5,74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stokke XPLORY V1 Manual

Product: