537128
16
Zoom out
Zoom in
Previous page
1/132
Next page
MS 201, MS 201 C
English
14
Low Kickback Saw Chain and
Reduced Kickback Bars
STIHL offers a variety of bars and
chains. STIHL reduced kickback bars
and low kickback chains are designed to
reduce the risk of kickback injury. Other
chains are designed to obtain higher
cutting efficiency or sharpening ease but
may result in higher kickback tendency.
STIHL has developed a color code
system to help you identify the STIHL
reduced kickback bars and low kickback
chains. Cutting attachments with green
warning decals or green labels on the
packaging are designed to reduce the
risk of kickback injury. The matching of
green decaled powerheads under
3.8 cubic inches (62 cm³) displacement
with green labeled bars and green
labeled chains gives compliance with
the computed kickback angle
requirements of ANSI B 175.1-2000
when the products are in their original
condition. Products with yellow decals or
labels are for users with extraordinary
cutting needs and experience and
specialized training for dealing with
kickback.
STIHL recommends the use of its
green labeled reduced kickback bars,
green labeled low kickback chains
and a STIHL Quickstop chain brake
for both experienced and
inexperienced chain saw users.
Please ask your STIHL dealer to
properly match your powerhead with the
appropriate bar / chain combination to
reduce the risk of kickback injury. Green
labeled bars and chains are
recommended for all powerheads.
Warning!
No Quickstop or other chain brake
device prevents kickback. These
devices are designed to reduce the risk
of kickback injury, if activated, in certain
kickback situations. In order for the
Quickstop to reduce the risk of kickback
injury, it must be properly maintained
and in good working order. See the
chapter of your instruction manual enti-
tled "Chain Brake" and the section
"Maintenance, Repair and Storing" at
the end of these Safety Precautions. In
addition, there must be enough distance
between the bar and the operator to
ensure that the Quickstop has sufficient
time to activate and stop the chain
before potential contact with the
operator.
Warning!
An improperly maintained chain brake
may increase the time needed to stop
the chain after activation, or may not
activate at all.
Warning!
Never run the chain saw above idle
speed for more than 3 seconds when
the chain brake is engaged or when the
chain is pinched or otherwise caught in
the cut. Clutch slippage can cause
excessive heat, leading to severe dam-
age of the motor housing, clutch and
oiler component and may interfere with
the operation of the chain brake. If
clutch slippage in excess of 3 seconds
has occurred, allow the motor housing
to cool before proceeding and check the
operation of your chain brake as
described in the chapter entitled "Chain
Brake" of your instruction manual. Also
make sure that the chain is not turning
at idle speed (see above at "Important
Adjustments").
Warning!
Use of other, non-listed bar / chain com-
binations may increase kickback forces
and the risk of kickback injury. New bar
/ chain combinations may be developed
after publication of this literature, which
will, in combination with certain power-
heads, comply with § 5.11 of ANSI
B 175.1-2000. Check with your STIHL
dealer for such combinations.
Warning!
Reduced kickback bars and low kick-
back chains do not prevent kickback,
but they are designed to reduce the risk
of kickback injury. They are available
from your STIHL dealer.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stihl STIHL MS 201 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stihl STIHL MS 201 in the language / languages: English, Spanish as an attachment in your email.

The manual is 3,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Stihl STIHL MS 201

Stihl STIHL MS 201 User Manual - German, Dutch, French, Italian - 200 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info