667248
11
Zoom out
Zoom in
Previous page
1/124
Next page
MS 193 T
English
9
Keep the handles clean and dry at all
times; it is particularly important to keep
them free of moisture, pitch, oil, fuel mix,
grease or resin in order for you to
maintain a firm grip and properly control
your chain saw .
WARNING
Be sure that the guide bar and saw chain
are clear of you and all other
obstructions and objects, including the
ground. If the upper quadrant of the tip of
the bar touches any object, it may cause
kickback to occur (see section on
reactive forces). Never attempt to start
the chain saw when the guide bar is in a
cut or kerf.
For specific starting instructions, see the
appropriate section of your instruction
manual.
Starting
WARNING
To reduce the risk of fire and burn
injuries, start the engine at least 10 feet
(3 m) from the fueling spot, outdoors
only.
Start and operate your chain saw
without assistance. For specific starting
instructions, see the appropriate section
of the instruction manual. Proper starting
methods reduce the risk of injury.
WARNING
To reduce the risk of injury from saw
chain contact and / or reactive forces,
the chain brake must be engaged when
starting the saw. If your chain saw is
equipped with the Quickstop Plus chain
brake system, it is not sufficient to
engage that brake only for starting,
because the saw chain may begin to
rotate at high speed when the throttle
trigger lockout is depressed (releasing
the brake) in order to blip the throttle
trigger after starting.
WARNING
Do not drop start. This method is very
dangerous because you may lose
control of the saw.
Place the chain saw on firm ground or
other solid surface in an open area.
Maintain good balance and secure
footing.
WARNING
Be sure that the guide bar and saw chain
are clear of you and all other
obstructions and objects, including the
ground. When the engine is started, the
engine speed with the starting throttle
lock engaged will be fast enough for the
clutch to engage the sprocket and, if the
chain brake is not activated, turn the
chain. If the upper quadrant of the tip of
the bar touches any object, it may cause
kickback to occur (see section on
reactive forces). To reduce this risk,
always engage the chain brake before
starting. Never attempt to start the chain
saw when the guide bar is in a cut or
kerf.
Once the engine has started,
immediately blip the throttle trigger,
which should release the Master Control
lever to the run position and allow the
engine to slow down to idle.
Always disengage chain brake before
accelerating engine and before starting
cutting work. The only exception to this
rule is when you check operation of the
chain brake. High revs with the chain
brake engaged (chain locked) will
quickly damage the powerhead and
chain drive (clutch, chain brake).
WARNING
When you pull the starter grip, do not
wrap the starter rope around your hand.
Do not let the grip snap back, but guide
the starter rope to rewind it properly.
Failure to follow this procedure may
result in injury to your hand or fingers
and may damage the starter
mechanism.
Important Adjustments
WARNING
To reduce the risk of personal injury
from loss of control and / or contact with
the running cutting tool, do not use your
chain saw with incorrect idle adjustment.
0012BA008 KN
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stihl MS193 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stihl MS193 in the language / languages: English, Spanish as an attachment in your email.

The manual is 3,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Stihl MS193

Stihl MS193 User Manual - German, Dutch, French, Italian - 196 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info