52243
12
Zoom out
Zoom in
Previous page
1/106
Next page
11HT 100, HT 101, HT 130, HT 131
English / USA
Make sure that the saw chain does not
touch any foreign materials such as
rocks, fences, nails and the like. Such
objects may be flung off and injure the
operator or bystanders, or damage the
saw chain.
!Warning!
Prior to limbing, clear the working area
from interfering limbs and brush. Then,
establish an escape area away from
where the cut limbs can fall, and remove
all obstacles.
Keep work area clear – move away
fallen limbs. Place all tools and
equipment at a safe distance from the
branches being limbed, but not in the
escape area.
!Warning!
Always observe the general condition of
the tree. Look for decay and rot in the
trunk and branches. If it is rotted inside,
it could snap and fall toward the operator
while being cut. Also look for broken or
dead branches which could vibrate
loose and fall on the operator.
If branch is thick or heavy, make a
shallow relief cut on the bottom of the
branch before cutting down from the top
to help prevent splitting of the branch.
!Warning!
To reduce the risk of severe or even fatal
injury from falling objects do not cut
vertically above your body. Hold the pole
pruner at an angle of not more than 60°
from the horizontal level (see picture).
Objects may fall in unexpected
directions. Do not stand directly
underneath the limb being cut!
Watch for falling wood! As soon as the
limbed branch starts to fall, step aside
and keep a sufficient distance away from
the falling wood.
!Warning
Always pull the unit out of the cut with
the chain running to reduce the
possibility of pinching the cutting
attachment. Don't put pressure on the
pole pruner when reaching the end of a
cut. The pressure may cause the bar
and rotating chain to pop out of the cut or
kerf, go out of control and strike some
other object.
If the bar becomes pinched and caught
in the branch so that the chain can no
longer move, shut off the pole pruner
and carefully move the branch to open
the pinch and release the bar.
!Warning!
The muffler and other parts of the engine
(e.g. fins of the cylinder, spark plug)
become hot during operation and remain
hot for a while after stopping the engine.
To reduce risk of burns do not touch the
muffler and other parts while they are
hot.
275BA005 KN
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stihl HT100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stihl HT100 in the language / languages: English as an attachment in your email.

The manual is 3,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Stihl HT100

Stihl HT100 User Manual - German, Dutch, French, Italian - 180 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info