667252
32
Zoom out
Zoom in
Previous page
1/96
Next page
HT 102, HT 103, HT 132, HT 133
English
30
During Break-In Period
A factory-new machine should not be
run at high revs (full throttle off load) for
the first three tank fillings. This avoids
unnecessary high loads during the
break-in period. As all moving parts
have to bed in during the break-in
period, the frictional resistances in the
engine are greater during this period.
The engine develops its maximum
power after about 5 to 15 tank fillings.
During Operation
NOTICE
Do not make the mixture leaner to
achieve an apparent increase in power
this could damage the engine – see
"Adjusting the Carburetor".
Check chain tension frequently
A new chain has to be retensioned more
often than one that has been in use for
some time.
Chain cold
Tension is correct when the chain fits
snugly against the underside of the bar
and can still be pulled along the bar by
hand. Retension if necessary – see
"Tensioning the Saw Chain".
Chain at operating temperature
The chain stretches and begins to sag.
The drive links must not come out of the
bar groove – the chain may otherwise
jump off the bar. Retension the chain –
see "Tensioning the Saw Chain".
After long period of full-throttle operation
Allow engine to run for a short while at
idle speed so that engine heat can be
dissipated by the flow of cooling air. This
protects engine-mounted components
(ignition, carburetor) from thermal
overload.
After Finishing Work
N Slacken off the chain if you have
retensioned it at operating
temperature during cutting work.
NOTICE
Always slacken off the chain after
finishing work. The chain contracts as it
cools down. If it is not slackened off, it
can damage the gear shaft and
bearings.
Storing your saw for a short period
Wait for the engine to cool down. Drain
the fuel tank. Store the machine in a dry
location. Check the tightness of all
accessible screws and nuts (not
adjusting screws) at regular intervals
and retighten if necessary.
Storing for a long period
See chapter on "Storing the Machine"
N Turn the bar over every time you
sharpen the chain and every time
you replace the chain – this helps
avoid one-sided wear, especially at
the nose and underside of the bar.
N Regularly clean the oil inlet hole (1),
the oilway (2) and the bar
groove (3).
N Measure the groove depth with the
scale on the filing gauge (special
accessory) – in the area used most
for cutting.
If groove depth is less than specified:
N Replace the guide bar.
Operating Instructions Taking Care of the Guide Bar
Chain type Chain pitch Minimum
groove depth
Picco 1/4" P 4.0 mm
(0.16 in)
1
2
3
246BA028 KN
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stihl HT 103 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stihl HT 103 in the language / languages: English, Spanish as an attachment in your email.

The manual is 5,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Stihl HT 103

Stihl HT 103 User Manual - German, Dutch, French, Italian - 156 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info