667251
29
Zoom out
Zoom in
Previous page
1/96
Next page
HT 102, HT 103, HT 132, HT 133
English
27
Cutting effortlessly with a correctly
sharpened chain
A properly sharpened chain slices
through wood effortlessly and requires
very little feed pressure.
Do not work with a dull or damaged
chain as it will increase the physical
effort required, produce unsatisfactory
results and a higher rate of wear.
N Clean the chain.
N Check the chain for cracks in the
links and damaged rivets.
N Replace any damaged or worn
parts of the chain and match the
new parts to the shape and size of
the original parts.
Carbide-tipped saw chains (Duro) are
particularly wear resistant. STIHL
recommends you have your chain
resharpened by a STIHL servicing
dealer.
WARNING
It is absolutely essential to comply with
the angles and dimensions specified
below. If the saw chain is incorrectly
sharpened and in particular if the depth
gauge is set too low – there is an
increased risk of kickback, with resulting
risk of injury.
The saw chain cannot be locked in place
on the guide bar. Therefore, it is best to
remove the chain from the bar and
resharpen it on a workshop sharpening
tool (FG 2, HOS, USG).
Chain pitch
The chain pitch (a) is marked on the
depth gauge end of each cutter.
Select file diameter according to chain
pitch – see table “Sharpening Tools”.
You must observe certain angles when
resharpening the chain cutter.
Filing and side plate angles
A Filing angle
STIHL saw chains are sharpened to a
filing angle of 30°. Exceptions are
ripping chains with a filing angle of 10°.
Ripping chains have an X in their
designations.
B Side plate angle
The correct side plate angle is obtained
automatically if you use the prescribed
file holder and file diameter.
The angles must be the same on all
cutters. If the angles are uneven: Chain
will run roughly, not in a straight line,
wear quickly and finally break.
File holder
N Use a file holder
A file holder must be used for manual
resharpening (see table "Sharpening
Tools"). The correct filing angles are
marked on the file holder.
Maintaining and Sharpening
the Saw Chain
Mark (a)Chain pitch
inch mm
7 1/4 P 6,35
1 or 1/4 1/4 6,35
6, P or PM 3/8 P 9,32
2 or 325 0.325 8,25
3 or 3/8 3/8 9,32
689BA027 KN
a
A
B
689BA021 KN
Cutter shapes Angle (°)
AB
Micro = semi chisel cutter,
e.g. 63 PM3, 26 RM3,
71 PM3
30 75
Super = chisel cutter, e.g.
63 PS3, 26 RS, 36 RS3
30 60
Ripping chain, e.g.
63 PMX, 36 RMX
10 75
689BA025 KN
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stihl HT 102 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stihl HT 102 in the language / languages: English, Spanish as an attachment in your email.

The manual is 5,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Stihl HT 102

Stihl HT 102 User Manual - German, Dutch, French, Italian - 156 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info