537300
9
Zoom out
Zoom in
Previous page
1/48
Next page
HL-KM
English
7
WARNING
If the vegetation being cut or the
surrounding ground is coated with a
chemical substance (such as an active
pesticide or herbicide), read and follow
the instructions and warnings that
accompanied the substance at issue.
WARNING
Substantial or repeated inhalation of
dust and other airborne contaminants, in
particular those with a smaller particle
size, may cause respiratory or other
illnesses. Control dust at the source
where possible. Use good work
practices, such as operating the unit so
that the wind or operating process
directs any dust raised by the power tool
away from the operator. Follow the
recommendations of EPA / OSHA /
NIOSH and occupational and trade
associations with respect to dust
("particulate matter"). When the
inhalation of dust cannot be
substantially controlled, i.e., kept at or
near the ambient (background) level, the
operator and any bystanders should
wear a respirator approved by NIOSH /
MSHA for the type of dust encountered.
Operating Instructions
WARNING
Do not operate your power tool using the
starting throttle lock, as you do not have
control of the engine speed.
In the event of an emergency, switch off
the engine immediately move the slide
control / stop switch / momentary stop
switch to 0 or STOP.
See section of your KombiEngine
instruction manual on the proper use of
the slide control / stop switch /
momentary stop switch.
WARNING
The cutting blades continue to move for
a short period after the throttle trigger is
released.
Accelerating the engine while the blades
are blocked increases the load and will
cause the clutch to slip continuously.
This may result in overheating and
damage to important components (e.g.
clutch, polymer housing components) –
which can then increase the risk of injury
from the blades moving while the engine
is idling.
WARNING
On units with an adjustable cutter bar:
Carefully adjust the cutter bar to the
desired cutting position.To reduce the
risk of injury, never touch the cutting
blades while making adjustments. Only
adjust the cutter bar when the blades are
no longer moving.
Stop the engine immediately if you are
approached.
WARNING
Before you start work, examine the
hedge area for stones, glass, fence wire,
metal, trash or other solid objects which
could damage the cutting blades.
Take particular care when cutting
hedges next to or against wire fences.
Do not touch the wire with the cutting
blades. When working close to the
ground, make sure that no sand, grit or
stones get between the cutting blades.
Striking solid foreign objects such as
stones, fence wire or metal could
damage the cutting attachment and may
cause blades to crack, chip or break.
STIHL does not recommend the use of
your power tool when cutting in areas
where the blades could contact such
objects.
Inhalation of certain
dusts, especially organic
dusts such as mold or
pollen, can cause sus-
ceptible persons to have
an allergic or asthmatic
reaction.
The power tool
has a large range.
In order to reduce
the risk of per-
sonal or even fatal
injury to bystand-
ers from falling
objects or inad-
vertent contact
with the moving
cutting blades of
your power tool
always keep
bystanders at least
50 feet (15 m)
away when the
power tool is
running.
15m (50ft)
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stihl HL-KM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stihl HL-KM in the language / languages: English, Spanish as an attachment in your email.

The manual is 2,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Stihl HL-KM

Stihl HL-KM User Manual - German, Dutch, French, Italian - 88 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info