537252
35
Zoom out
Zoom in
Previous page
1/124
Next page
FS 260 C, FS 360 C
English
33
Other Hints on Starting
At very low outside temperatures
N Set the engine to winter operation if
necessary, see "Winter Operation".
N If your machine is very cold (frost or
ice on machine), start the engine
and keep it at a high idle speed
(cutting attachment rotates) until it
reaches normal operating
temperature.
Engine stalls in cold start position g or
under acceleration
N Move the choke lever to < and
continue cranking until the engine
runs.
Engine does not start in hot start
position <
N Move the choke lever to g and
continue cranking until the engine
runs.
If the engine does not start
N Check that all settings are correct.
N Check that there is fuel in the tank
and refuel if necessary.
N Check that the spark plug boot is
properly connected.
N Repeat the starting procedure.
Fuel tank run until completely dry
Recommendation: Carry out the
following steps irrespective of the
engine's operating condition before the
tank was run dry.
N Set the choke lever to g.
N Go to section on "Starting the
Engine" and re-start the engine as
described for a cold engine.
During break-in period
A factory-new machine should not be
run at high revs (full throttle off load) for
the first three tank fillings. This avoids
unnecessary high loads during the
break-in period. As all moving parts
have to bed in during the break-in
period, the frictional resistances in the
engine are greater during this period.
The engine develops its maximum
power after about 5 to 15 tank fillings.
During Operation
After a long period of full throttle
operation, allow the engine to run for a
short while at idle speed so that engine
heat can be dissipated by the flow of
cooling air. This protects engine-
mounted components (ignition,
carburetor) from thermal overload.
After Finishing Work
Storing for a short period: Wait for the
engine to cool down. Empty the fuel tank
and keep the machine in a dry place,
well away from sources of ignition, until
you need it again. For longer out-of-
service periods – see "Storing the
Machine".
Operating Instructions
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stihl FS 360 C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stihl FS 360 C in the language / languages: English, Spanish as an attachment in your email.

The manual is 3,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Stihl FS 360 C

Stihl FS 360 C User Manual - German - 212 pages

Stihl FS 360 C Additional guide - Dutch - 20 pages

Stihl FS 360 C User Manual - Dutch, French, Italian - 212 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info