537253
30
Zoom out
Zoom in
Previous page
1/98
Next page
29FS 300, FS 350, FS 400, FS 450, FS 480
English / USA
: Place the unit on the ground:
It must rest securely on the engine
support and the deflector. Check
that the cutting tool is not touching
the ground or any other obstacles.
: Make sure you have a firm footing.
: Press the unit firmly against the
ground with your left hand.
Do not stand or kneel on the drive
tube.
: Pull the starter grip slowly with your
right hand until you feel it engage –
and then give it a brisk strong pull.
Do not pull out the starter rope to full
length – it might break.
: Do not let the starter grip snap back
– guide it slowly into the housing so
that the starter rope can rewind
properly.
: Continue cranking.
When engine begins to fire
: Turn the choke knob to e
: Press in decompression valve
button again and continue cranking.
As soon as the engine runs
: Blip the throttle trigger (2) so that the
slide control (3) moves to the normal
run position # and the engine settles
down to idle speed.
Make sure the carburetor is
correctly adjusted – the cutting tool
must not rotate when the engine is
idling.
Your brushcutter is now ready for
operation.
To shut down the engine
: Move the slide control to 0 c
At very low outside temperatures:
As soon as engine runs:
: Blip the throttle trigger. The slide
control moves to the normal run
position # and the engine settles
down to idle speed.
: Open the throttle slightly.
: Warm up engine for brief period.
FS 400, 450: Change over to winter
operation if necessary – see chapter
"Winter Operation".
If the engine does not start
If you did not turn the choke knob to e
(warm start) quickly enough after the
engine began to fire, the combustion
chamber has flooded.
: Set slide control, interlock lever and
throttle trigger to the starting throttle
position.
: Start the engine by pulling the
starter rope firmly. 10 to 20 pulls
may be necessary.
256BA021 KN
3
START
2
STOP
256BA022 KN
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stihl FS 300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stihl FS 300 in the language / languages: English, Spanish as an attachment in your email.

The manual is 2,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Stihl FS 300

Stihl FS 300 User Manual - German - 168 pages

Stihl FS 300 Additional guide - Dutch - 20 pages

Stihl FS 300 User Manual - Dutch, French, Italian - 168 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info