667512
9
Zoom out
Zoom in
Previous page
1/80
Next page
FB 131
English
7
WARNING
The cutting attachment and deflector
must be properly tightened and in safe
operating condition. Inspect for loose
parts (nuts, screws, etc.) and for
cracked, bent, warped or damaged
blades. Replace a damaged blade or
deflector before using the power tool.
Keep the handles clean and dry at all
times; it is particularly important to keep
them free of moisture, pitch, oil, fuel mix,
grease or resin in order for you to
maintain a firm grip and properly control
your power tool.
WARNING
Check that the spark plug boot is
securely mounted on the spark plug – a
loose boot may cause arcing that could
ignite combustible fumes and cause a
fire.
WARNING
An arrow on the deflector shows the
correct direction of rotation of the cutting
blade.
The arrow on the deflector must always
face away from you, so that cuttings and
other debris will be diverted away from
the machine and your position (see
chapter "Working Techniques".)
For proper control and less fatigue
during operation, adjust the loop handle
to suit your size before starting work.
Starting
WARNING
To reduce the risk of serious personal
injury from fire, start the engine at least
10 feet (3 m) from the fueling spot,
outdoors only.
For specific starting instructions, see the
appropriate section of your manual.
Place the power tool on firm ground or
other solid surface in an open area.
Maintain good balance and secure
footing.
WARNING
To reduce the risk of injury from blade
contact, be absolutely sure that the
cutting attachment is clear of you and all
other obstructions and objects, including
the ground, because when the engine
starts at starting-throttle, engine speed
will be fast enough for the clutch to
engage and move the cutting
attachment.
Once the engine has started,
immediately blip the throttle trigger,
which should release the starting throttle
and allow the engine to slow down to
idle.
WARNING
Your power tool is a one-person
machine. Do not allow other persons in
the general work area, even when
starting.
WARNING
To reduce the risk of injury from loss of
control, do not attempt to "drop start"
your power tool. Drop starting means
pushing the machine away from the
operator, or allowing it to drop toward
the ground, while pulling on the starter
grip. This method is very dangerous
bescause you may lose control of the
machine.
WARNING
When you pull the starter grip, do not
wrap the starter rope around your hand.
Do not let the grip snap back, but guide
the starter rope to permit the rope to
rewind properly. Failure to follow this
procedure may result in injury to your
hand or fingers and may damage the
starter mechanism.
To reduce the risk
of personal injury
to the operator
from blade con-
tact and thrown
objects, make sure
your unit is
equipped with the
proper deflector,
skirt and handle.
9924BA001 KN
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stihl FB131 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stihl FB131 in the language / languages: English, Spanish as an attachment in your email.

The manual is 3,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info