52153
41
Zoom out
Zoom in
Previous page
1/54
Next page
Adjusting Carburetor
Motor management
Exhaust emissions are controlled by the
design of the fundamental engine
parameters and components
(e.g. carburetion, ignition, timing and
valve or port timing) without the addition
of any major hardware.
The carburetor is set at the factory to
provide an optimum fuel-air mixture
under all operating conditions.
It enables your machine to run smoothly,
be fuel efficient, operate reliably and
produce low emissions.
Standard setting and explanation of
setting pictograms
Check the air filter and clean or
replace it if necessary
Check the spark arresting screen
and clean or replace it if necessary
Turn the high speed adjusting
screw (H) counterclockwise up to
the stop, i.e. 3/4 turn from max.
lean setting
Turn the low speed adjusting
screw (L) clockwise up to the stop
- then back off the screw one
quarter of a turn
H
3
4
/
4
L
1
/
Correction of carburetor setting for
higher altitudes
If the engine runs unsatisfactorily, slight
readjustment may be necessary:
Check standard setting
warm up the engine
Turn the high speed adjusting
screw (H) and low speed adjusting
screw (L) clockwise (leaner) -
!
Warning!
If you make the setting too lean, the
maximum permissible engine speed will
be exceeded - risk of engine damage.
Setting idle speed
It is usually necessary to change the
setting of the idle speed adjusting screw
(LA) after every correction to the low
speed adjusting screw (L).
Engine stops while idling
Turn the idle speed adjusting
screw (LA) clockwise until
chain begins to run -
then back off the screw one quarter
of a turn
Chain runs when engine is idling
Turn the idle speed adjusting
screw (LA) counterclockwise until
chain stops running -
then turn screw another
quarter turn in the same direction
Erratic idling behavior,
poor acceleration
Idle setting is too lean
Turn the low speed adjusting
screw (L) counterclockwise -
no further than stop -
until engine runs and accelerates
smoothly -
4
L
H
3
1
/
4
/
L
A
L
H
137BA021 KN
066 39
41


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Stihl 066 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Stihl 066 in the language / languages: English as an attachment in your email.

The manual is 2,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info