Manual Stiga TORNADO 2098 (page 70 of 112) (English, German, Dutch, French, Italian)

608469

Zoom out

Zoom in

1/112

IMPORTANT This connector must only be

used for connection to the maintenance battery-

charger indicated by the Manufacturer. For its

use:

– follow the instructions given in the relative in-

structions manual;

– follow the instructions in the battery manual.

6.3 INTERVENTIONS ON THE MACHINE

6.3.1 Aligning the cutting-means

assembly (Fig. 6.3)

The cutting-means assembly should be prop-

erly adjusted to obtain an evenly mown lawn.

If mowing is uneven, check the tyre pressure.

If this is not sucient to achieve an even cut,

please contact your Dealer to adjust the align-

ment of the cutting-means assembly.

6.3.2 Replacing the wheels (Fig. 6.4)

Stop the machine on at ground and put a block

under a load-bearing part of the frame on the

side that the wheel is to be changed.

The wheels are held by a snap ring (1) which

can be removed with a screwdriver.

NOTE If you have to replace one or both rear

wheels, make sure that any differences in their

external diameter does not exceed 8-10 mm; on

the contrary, you must adjust the cutting-means

assembly alignment to prevent uneven mowing.

IMPORTANT Before remounting the wheel,

apply grease to the axle. Put the snap ring (1)

and shoulder washer (2) back in place.

6.3.3 Repairing or replacing tyres

The tyres are “Tubeless” and must be replaced

or repaired if punctured by a specialized tyre

repairer following the procedures required for

this kind of tyre.

6.3.4 Replacing bulbs ( if tted)

• Type “I” bulbs (incandescent) (Fig. 6.5)

The bulbs (18W) have a bayonet tting and are

installed in the bulb holder which can be taken

out by turning it anti-clockwise with pliers.

• Type “II” bulbs (LED) Fig. 6.6)

Unscrew the ring-nut (1) and remove the con-

nector (2).

Remove the LED illuminator (3), secured by

screws (4).

6.3.5 Replacing a fuse (Fig. 6.7)

The machine is tted with fuses (1) with dierent

capacities and functions. Specically:

– 10 A fuse = protects the main and power cir-

cuits of the electronic circuit board. When it

blows, the machine stops.

– 25 A fuse = protects the battery recharge cir-

cuit. When it blows, the battery gradually runs

down and the machine will have problems

starting.

The fuse capacity is indicated on the fuse.

IMPORTANT A blown fuse must always be

replaced by one of the same type and ampere

rating, and never with one of another rating.

If you are unable to understand why it has

blown, contact Your Dealer.

6.3.6 R emoving, replacing and

reassembling of cutting means

WARNING! Always wear strong protec-

tive gloves to handle the cutting means.

WARNING! Always replace damaged or

bent cutting means; never attempt to repair

them! ALWAYS USE ORIGINAL CUTTING

MEANS!

Only cutting means bearing the code indicated

in the table on page ii must be used on this ma-

chine.

Given product evolution, the above mentioned

cutting means may be replaced in time with oth-

ers having similar interchangeable and operat-

ing safety features.

IMPORTANT Cutting means should be

replaced in pairs, especially when there are

marked differences in wear.

dimenzije pogonskih jermenov za stigo tornado 2098H Submitted on 28-5-2021 at 16:18
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Stiga TORNADO 2098 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 2,7 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Stiga TORNADO 2098 Manual

Product: